FORD M99C110-A (H)-2009 EXTRUSION OIL HIGH VISCOSITY《高粘度挤压油》.pdf

《FORD M99C110-A (H)-2009 EXTRUSION OIL HIGH VISCOSITY《高粘度挤压油》.pdf》由会员分享，可在线阅读，更多相关《FORD M99C110-A (H)-2009 EXTRUSION OIL HIGH VISCOSITY《高粘度挤压油》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 NON-PRODUCTION MATERIAL SPECIFICATION Material Name Specification Number Date Action Changes 2009 06 24 N-STATUS No Replacement Named L. Sinclair, NA 1987 06 01 Page 1 of 2 EXTRUSION OIL HIGH VISCOSITY M99C110-A(H) NOT TO BE USED FOR NEW DESIGN 1. SCOPE: The material defined by this standard is a h

2、igh viscosity chlorinated drawing oil. 2. APPLICATION: This material is used as a drawing oil for forming strut tubing on tube end forming machines. 3. REQUIREMENTS: 3.1 CHEMICAL COMPOSITION: 3.1.1 SOAPS (WT. %) 2.5 min (FLTM AJ 6-1) 3.1.2 NON SAPONIFIABLES (WT. %) 86.0 max (FLTM AJ 6-1) 3.1.3 RECOV

3、ERED SAPONIFIABLES (WT. %) 0.6 min (FLTM AJ 6-1) 3.1.4 TOTAL CHLORINE (WT. %) 16.5 min (ASTM D 808) 3.1.5 TOTAL SULFUR (WT. %) 0.50 max (ASTM D 129) 3.1.6 FREE SULFUR (WT. %) 0.05 min (FLTM AJ 1-1) 3.1.7 WATER CONTENT (VOL. %) 0.1 (ASTM D 95) 3.1.8 INFRARED SPECTROPHOTOMETRY: Ford Motor Company, at

4、its option, may conduct infrared analysis of material supplied to this specification. The curves established for initial approval shall constitute the reference standard and shall be kept on file at Central Laboratory. All samples shall produce curves that correspond to the reference standard when t

5、ested under the same conditions as those specified on the master curve. NON-PRODUCTION MATERIAL SPECIFICATION M99C110-A (H) Page 2 of 2 3.2 PHYSICAL: 3.2.1 VISCOSITY cSt 40 C: 245-255 (ASTM D 445) 3.2.2 VISCOSITY cSt 100 C: 15.0-18.0 (ASTM D 445) 3.2.3 FLASH POINT C: 160 min (ASTM D 92) 3.2.4 FIRE P

6、OINT C: 190 min (ASTM D 92) 3.2.5 SUPPLIERS RESPONSIBILITY: All materials supplied to this standard must be equivalent in all characteristics to the material upon which approval was originally granted, and shall be suitable for the intended application. Changes in composition shall not be made witho

7、ut approval of the responsible Staff Office in accordance with Manufacturing Procedure IId1. 3.2.6 IDENTIFICATION: Materials supplied to this standard shall be identified with the “M“ number printed on the side as well as the top of the containers in letters at least 2“ (50mm) high in a contrasting

8、color to the that of the container. Container marking shall be in accordance with Manufacturing Standard ZF-10 and conform to all Federal, State, and Local container contents labeling regulations which are in effect both in the area of shipment and use. 4. APPROVAL OF NEW SUPPLIERS: Materials submit

9、ted by new manufacturers to this standard must have Regulatory Clearance, Hygiene Laboratory and Shop Trial approvals. Suppliers are required to complete and submit the Material Health, Safety and Environmental Data Sheet (Form 1291A) prior to Shop Trial. Recommendations for the addition of new manu

10、facturers to the Manufacturing Approved Source List (ASL) must be made in writing to the responsible Staff Office by the appropriate divisional standards activity in accordance with Manufacturing Procedure IId1. 5. ENVIRONMENTAL CONTROL: Use of any material approved to this standard must comply with

11、 the guidelines as established in the environmental review of the material as they appear in the Materials and Toxicology System (MATS). 6. HEALTH AND SAFETY: Use of any material approved to this standard must comply with the guidelines given under the Toxicological (TOX) review of the material as indicated in the MATS system.