EN ISO TS 14253-4-2010 en Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 4 Background on functional limits and sp.pdf

《EN ISO TS 14253-4-2010 en Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 4 Background on functional limits and sp.pdf》由会员分享，可在线阅读，更多相关《EN ISO TS 14253-4-2010 en Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 4 Background on functional limits and sp.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、DD CEN ISO/TS14253-4:2010ICS 17.040.01NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWDRAFT FOR DEVELOPMENTGeometrical productspecifications (GPS) Inspection bymeasurement ofworkpieces andmeasuring equipmentPart 4: Background on functionallimits and specification limits indecis

2、ion rules (ISO/TS 14253-4:2010)This Draft for Development was published under the authority of the Standards Policy and Strategy Committee on 30 June 2010 BSI 2010ISBN 978 0 580 66899 9Amendments/corrigenda issued since publicationDate CommentsDD CEN ISO/TS 14253-4:2010National forewordThis Draft fo

3、r Development is the UK implementation of CEN ISO/TS 14253-4:2010.This publication is not to be regarded as a British Standard.It is being issued in the Draft for Development series of publications and is of a provisional nature. It should be applied on this provisional basis, so that information an

4、d experience of its practical application can be obtained.Comments arising from the use of this Draft for Development are requested so that UK experience can be reported to the international organization responsible for its conversion to an international standard. A review of this publication will b

5、e initiated not later than 3 years after its publication by the international organization so that a decision can be taken on its status. Notification of the start of the review period will be made in an announcement in the appropriate issue of Update Standards.According to the replies received by t

6、he end of the review period, the responsible BSI Committee will decide whether to support the conversion into an international Standard, to extend the life of the Technical Specification or to withdraw it. Comments should be sent to the Secretary of the responsible BSI Technical Committee at British

7、 Standards House, 389 Chiswick High Road, London W4 4AL.The UK participation in its preparation was entrusted to Technical Committee TDW/4, Technical Product Realization.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purpor

8、t to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.TECHNICAL SPECIFICATION SPCIFICATION TECHNIQUE TECHNISCHE SPEZIFIKATION CEN ISO/TS 14253-4 May 2010 ICS 17.040.0

9、1 English Version Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 4: Background on functional limits and specification limits in decision rules (ISO/TS 14253-4:2010) Spcification gomtrique des produits (GPS) - Vrification par la mesur

10、e des pices et des quipements de mesure - Partie 4: Informations de base sur les limites fonctionnelles et les limites de spcification dans les rgles de dcision (ISO/TS 14253-4:2010) Geometrische Produktspezifikationen (GPS) - Prfung von Werkstcken und Messgerten durch Messen - Teil 4: Grundlagen fr

11、 Funktionsgrenzen und Spezifikationsgrenzen in Entscheidungsregeln (ISO/TS 14253-4:2010) This Technical Specification (CEN/TS) was approved by CEN on 4 April 2010 for provisional application. The period of validity of this CEN/TS is limited initially to three years. After two years the members of CE

12、N will be requested to submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard. CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available promptly at national level in an ap

13、propriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czec

14、h Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EURO

15、PEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. CEN ISO/TS 14253-4:2010: EDD CEN ISO/TS 14253-4:2010CEN ISO/TS 14253-4:2010

16、(E) 3 Foreword This document (CEN ISO/TS 14253-4:2010) has been prepared by Technical Committee ISO/TC 213 “Dimensional and geometrical product specifications and verification“ in collaboration with Technical Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” t

17、he secretariat of which is held by AFNOR. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regula

18、tions, the national standards organizations of the following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg,

19、 Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO/TS 14253-4:2010 has been approved by CEN as a CEN ISO/TS 14253-4:2010 without any modification. DD CEN ISO/TS 14253-4:2010ISO/TS 14253-4:2

20、010(E) ISO 2010 All rights reserved iiiContents Page Foreword iv Introduction.v 1 Scope1 2 Normative references1 3 Definitions 1 4 Relationship between functional limits and specification limits2 4.1 General .2 4.2 The one-sided case .2 4.3 The two-sided case .6 5 How functional limits are determine

21、d .9 5.1 Ideal situation 9 5.2 Use of earlier models 9 5.3 Reverse engineering .9 5.4 Trial and error 10 5.5 Method based on a set of working examples.10 6 Specification limits and how specification limits are determined relative to functional limits .10 6.1 General .10 6.2 Ideal situation 10 6.3 Sp

22、ecification reduced by assumed measurement uncertainty 10 6.4 Specification reduced by an arbitrary amount.11 7 Shape of assumed functional deterioration curve.11 7.1 Ideal situation 11 7.2 Gradual deterioration11 8 Determining specification limits 12 8.1 Ideal situation 12 8.2 Batch parts made by d

23、esired process 12 9 Alternative basis for decision rules.12 9.1 General .12 9.2 Alternative decision rules.12 9.3 Choice of alternative decision rules13 Annex A (informative) Relation to the GPS matrix model.14 Bibliography16 DD CEN ISO/TS 14253-4:2010ISO/TS 14253-4:2010(E) iv ISO 2010 All rights re

24、servedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for whi

25、ch a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all m

26、atters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are cir

27、culated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. In other circumstances, particularly when there is an urgent market requirement for such documents, a technical committee may decide to publish ot

28、her types of document: an ISO Publicly Available Specification (ISO/PAS) represents an agreement between technical experts in an ISO working group and is accepted for publication if it is approved by more than 50 % of the members of the parent committee casting a vote; an ISO Technical Specification

29、 (ISO/TS) represents an agreement between the members of a technical committee and is accepted for publication if it is approved by 2/3 of the members of the committee casting a vote. An ISO/PAS or ISO/TS is reviewed after three years in order to decide whether it will be confirmed for a further thr

30、ee years, revised to become an International Standard, or withdrawn. If the ISO/PAS or ISO/TS is confirmed, it is reviewed again after a further three years, at which time it must either be transformed into an International Standard or be withdrawn. Attention is drawn to the possibility that some of

31、 the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO/TS 14253-4 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product specifications and verification. ISO 14253 consists

32、of the following parts, under the general title Geometrical product specifications (GPS) Inspection by measurement of workpieces and measuring equipment: Part 1: Decision rules for proving conformance or non-conformance with specifications Part 2: Guidance for the estimation of uncertainty in GPS me

33、asurement, in calibration of measuring equipment and in product verification Part 3: Guidelines for achieving agreements on measurement uncertainty statements Part 4: Background on functional limits and specification limits in decision rules Technical Specification DD CEN ISO/TS 14253-4:2010ISO/TS 1

34、4253-4:2010(E) ISO 2010 All rights reserved vIntroduction This part of ISO 14253 is a geometrical product specifications (GPS) standard and is to be regarded as a global GPS standard (see ISO/TR 14638). It influences the chain links 3, 4, 5 and 6 of all chains of general GPS standards. For more deta

35、iled information on the relation of this part of ISO 14253 to other standards and the GPS matrix model, see Annex A. The decision rules given in ISO 14253-1, which apply unless otherwise specified, are designed to ensure that workpieces and measuring equipment are within the specification and that d

36、isputes over whether workpieces and measuring equipment are within the specification can be avoided. In order for the decision rules to work as designed, it is important to first give proof of conformance. In other words, the user/buyer of the product in question should always require the manufactur

37、er/supplier/seller of the product to provide proof of conformance with the product. If subsequent incoming inspection proves nonconformance, uncertainty budgets can be examined according to ISO 14253-3 for mutual assurance of their validity. If it is concluded that both uncertainty budgets are valid

38、, the only conclusion is that one or the other or both measurement results are unrepresentative for the measurement process in question. If, for some reason, the user of the product does not want the supplier to provide the first proof, but instead relies on incoming inspection, the user should redu

39、ce the functional limits by the measurement uncertainty of the incoming inspection to arrive at the contractual specification limits that are communicated to, and negotiated and agreed with, the supplier. A separate problem is that of the reseller, who purchases product from a manufacturer and resel

40、ls it to the user. The decision rules given in ISO 14253-1 will function correctly if the reseller requires the manufacturer of the product to provide proof of conformance and subsequently provides that proof to the user. If the reseller for some reason decides to prove conformance to the user indep

41、endently, there will be cases where neither conformance nor nonconformance can be proven, so the reseller can neither return nor resell the product based on the original specification. Consequently, this approach is not recommended. The decision rules in ISO 14253-1 are also based on a number of ass

42、umptions. When these assumptions are not true, these decision rules may not be economically optimal. This part of ISO 14253 outlines these assumptions and discusses why they are the theoretically ideal assumptions. For workpieces, only the creator of the specification (the designer) can be expected

43、to know whether the assumptions are true. Therefore, any deviations from the ISO 14253-1 decision rules can only be initiated and documented by the specification owner. For measuring equipment, a specification may be based on a standard, written unilaterally by the manufacturer or purchaser of the e

44、quipment or written in cooperation between the manufacturer and the purchaser of the equipment. If the specification is based on an ISO standard, and the standard does not indicate other decision rules, the rules of ISO 14253-1 apply. In other cases, the decision rules can only be documented by the

45、specification author(s). It must be recognized that the decision rules, whether they are given implicitly or explicitly, are part of the specification. It must further be recognized that the issues involved in choosing the optimal set of decision rules are complicated and that it is unrealistic to e

46、xpect that simple rules can suit every circumstance. Parties should ensure access to competent technical resources before deviating from the ISO 14253-1 decision rules. DD CEN ISO/TS 14253-4:2010ISO/TS 14253-4:2010(E) vi ISO 2010 All rights reservedIn this case, the specification owner must explicit

47、ly recognize that decision rules other than those defined in ISO 14253-1 apply, and that documentation of this policy needs to be prepared and be made available to trading partners (customers and/or suppliers) and be referenced in the technical product documentation. DD CEN ISO/TS 14253-4:2010TECHNI

48、CAL SPECIFICATION ISO/TS 14253-4:2010(E) ISO 2010 All rights reserved 1Geometrical product specifications (GPS) Inspection by measurement of workpieces and measuring equipment Part 4: Background on functional limits and specification limits in decision rules 1 Scope This part of ISO 14253 outlines t

49、he main assumptions behind the theoretically ideal decision rules established in ISO 14253-1. It discusses why these rules have to be the default rules and what considerations should be taken into account before applying different decision rules. This part of ISO 14253 applies to all specifications defined in general GPS standards (see ISO/TR 14638), i.e. standards prepared by ISO/TC 213, including workpiece specifications (usually given as specification limits), and measuring equipment specifications (usually given as m