EN ISO 18563-2-2017 en Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 2 Probes.pdf

《EN ISO 18563-2-2017 en Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 2 Probes.pdf》由会员分享，可在线阅读，更多相关《EN ISO 18563-2-2017 en Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 2 Probes.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、Non-destructive testing Characterization and verification of ultrasonic phased array equipmentPart 2: ProbesBS EN ISO 18563-2:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 18563-2 August 2017 ICS 19.100 S

2、upersedes EN 16392-2:2014English Version Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 2: Probes (ISO 18563-2:2017) Essais non destructifs - Caractrisation et vrification de lappareillage de contrle par ultrasons en multilments - Partie 2: Tr

3、aducteurs (ISO 18563-2:2017) Zerstrungsfreie Prfung - Charakterisierung und Verifizierung der Ultraschall-Prfausrstung mit Phased-Arrays - Teil 2: Prfkpfe (ISO 18563-2:2017)This European Standard was approved by CEN on 3 May 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulat

4、ions which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

5、 This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN

6、members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Po

7、rtugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitatio

8、n in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 18563-2:2017 ENational forewordThis British Standard is the UK implementation of EN ISO 18563-2:2017. It supersedes BS EN 16392-2:2014 which is withdrawn.The UK participation in its preparation was entrusted

9、to Technical Committee WEE/46, Non-destructive testing.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The Bri

10、tish Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 94451 2ICS 19.100Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 Septemb

11、er 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN ISO 18563-2:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 18563-2 August 2017 ICS 19.100 Supersedes EN 16392-2:2014English Version Non-destructive testing - Characterization and verification

12、of ultrasonic phased array equipment - Part 2: Probes (ISO 18563-2:2017) Essais non destructifs - Caractrisation et vrification de lappareillage de contrle par ultrasons en multilments - Partie 2: Traducteurs (ISO 18563-2:2017) Zerstrungsfreie Prfung - Charakterisierung und Verifizierung der Ultrasc

13、hall-Prfausrstung mit Phased-Arrays - Teil 2: Prfkpfe (ISO 18563-2:2017)This European Standard was approved by CEN on 3 May 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standa

14、rd without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any

15、 other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Repub

16、lic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. E

17、UROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 18563-2:2

18、017 EBS EN ISO 18563-2:2017EN ISO 18563-2:2017 (E) 2 European foreword This document (EN ISO 18563-2:2017) has been prepared by Technical Committee ISO/TC 135 “Non-destructive testing” in collaboration with Technical Committee CEN/TC 138 “Non-destructive testing” the secretariat of which is held by

19、AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2018, and conflicting national standards shall be withdrawn at the latest by February 2018. Attention is drawn to the possibility th

20、at some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 16392-2:2014. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the foll

21、owing countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,

22、Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 18563-2:2017 has been approved by CEN as EN ISO 18563-2:2017 without any modification. ISO 18563-2:2017(E)Foreword iv1 Scope . 12 Normative ref

23、erences 13 Terms and definitions . 14 Symbols 25 General compliance . 26 Technical information for phased array probes 27 Test equipment. 47.1 Electronic equipment 47.2 Test blocks and other equipment 47.2.1 General 47.2.2 Contact technique . 47.2.3 Immersion technique . 48 Performance tests for pha

24、sed array probes 48.1 General . 48.2 Physical aspects 58.2.1 Method 58.2.2 Acceptance criterion . 58.3 Relative pulse-echo sensitivity variation 58.3.1 General 58.3.2 Method 58.3.3 Acceptance criteria 58.4 Frequency, bandwidth and pulse duration . 68.4.1 General 68.4.2 Method 68.4.3 Acceptance crite

25、ria 68.5 Probe sensitivity 78.5.1 General 78.5.2 Method 78.5.3 Acceptance criteria 78.6 Inter-element cross-talk (optional) 78.6.1 General 78.6.2 Method 78.6.3 Acceptance criterion . 88.7 Number of elements “out of specification” . 88.7.1 General 88.7.2 Method 88.7.3 Acceptance criteria 8Bibliograph

26、y 9 ISO 2017 All rights reserved iiiContents PageBS EN ISO 18563-2:2017ISO 18563-2:2017(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Symbols 25 General compliance . 26 Technical information for phased array probes 27 Test equipment. 47.1 Electronic equipment 47.2 Test

27、 blocks and other equipment 47.2.1 General 47.2.2 Contact technique . 47.2.3 Immersion technique . 48 Performance tests for phased array probes 48.1 General . 48.2 Physical aspects 58.2.1 Method 58.2.2 Acceptance criterion . 58.3 Relative pulse-echo sensitivity variation 58.3.1 General 58.3.2 Method

28、 58.3.3 Acceptance criteria 58.4 Frequency, bandwidth and pulse duration . 68.4.1 General 68.4.2 Method 68.4.3 Acceptance criteria 68.5 Probe sensitivity 78.5.1 General 78.5.2 Method 78.5.3 Acceptance criteria 78.6 Inter-element cross-talk (optional) 78.6.1 General 78.6.2 Method 78.6.3 Acceptance cr

29、iterion . 88.7 Number of elements “out of specification” . 88.7.1 General 88.7.2 Method 88.7.3 Acceptance criteria 8Bibliography 9 ISO 2017 All rights reserved iiiContents PageBS EN ISO 18563-2:2017ISO 18563-2:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide fed

30、eration of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that comm

31、ittee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document an

32、d those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Par

33、t 2 (see www .iso .org/ directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of

34、 the document will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of st

35、andards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .htmlThis document wa

36、s prepared by the European Committee for Standardization (CEN) Technical Committee CEN/TC 138, Non-destructive testing, in collaboration with ISO Technical Committee TC 135, Non-destructive testing, Subcommittee SC 3, Ultrasonic testing, in accordance with the Agreement on technical cooperation betw

37、een ISO and CEN (Vienna Agreement).A list of all parts in the ISO 18563 series can be found on the ISO website. iv ISO 2017 All rights reservedBS EN ISO 18563-2:2017ISO 18563-2:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bod

38、ies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organization

39、s, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further

40、maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directive

41、s).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Intr

42、oduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO speci

43、fic terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .htmlThis document was prepared by the European Commit

44、tee for Standardization (CEN) Technical Committee CEN/TC 138, Non-destructive testing, in collaboration with ISO Technical Committee TC 135, Non-destructive testing, Subcommittee SC 3, Ultrasonic testing, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement

45、).A list of all parts in the ISO 18563 series can be found on the ISO website. iv ISO 2017 All rights reserved INTERNATIONAL STANDARD ISO 18563-2:2017(E)Non-destructive testing Characterization and verification of ultrasonic phased array equipment Part 2: Probes1 ScopeThis document specifies the cha

46、racterization tests performed at the end of the fabrication of a phased array probe. It defines both methodology and acceptance criteria.This document is applicable to the following phased array probes used for ultrasonic non-destructive testing in contact technique (with or without a wedge) or in i

47、mmersion technique, with centre frequencies in the range 0,5 MHz to 10 MHz:a) non-matrix array probes: linear; encircling; partial annular sectorial (type “daisy”);b) 2D-matrix array probes.This document does not give methods and acceptance criteria to characterize the performance of an ultrasonic p

48、hased array instrument or the performance of a combined system. These are given in ISO 185631 and in ISO 185633.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, o

49、nly the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 2400, Non-destructive testing Ultrasonic testing Specification for calibration block No. 1ISO 5577, Non-destructive testing Ultrasonic testing VocabularyEN 16018, Non-destructive testing Terminology Terms used in ultrasonic testing with phased arrays3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 5577 and EN 16018 and the follow