EN IEC 62386-216-2018 en Digital addressable lighting interface - Part 216 Particular requirements for control gear - Load referencing (device type 15).pdf

《EN IEC 62386-216-2018 en Digital addressable lighting interface - Part 216 Particular requirements for control gear - Load referencing (device type 15).pdf》由会员分享，可在线阅读，更多相关《EN IEC 62386-216-2018 en Digital addressable lighting interface - Part 216 Particular requirements for control gear - Load referencing (device type 15).pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Digital addressable lighting interfacePart 216: Particular requirements for control gear - Load referencing (device type 15)BS EN IEC 62386-216:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IEC 62386-216 June

2、 2018 ICS 29.140.50; 29.140.99 English Version Digital addressable lighting interface - Part 216: Particular requirements for control gear - Load referencing (device type 15) (IEC 62386-216:2018) Interface dclairage adressable numrique - Partie 216: Exigences particulires pour les appareillages de c

3、ommande - Rfrence de charge (dispositifs de type 15) (IEC 62386-216:2018) Digital adressierbare Schnittstelle fr die Beleuchtung - Teil 216: Anforderungen fr Betriebsgerte - Last-Referenzierung (Gertetyp 15) (IEC 62386-216:2018) This European Standard was approved by CENELEC on 2018-05-28. CENELEC m

4、embers are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on applic

5、ation to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENE

6、LEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Ice

7、land, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechniq

8、ue Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN IEC 62386-216:2018 E National forewordThis British Standar

9、d is the UK implementation of EN IEC 62386216:2018. It is identical to IEC 62386216:2018. The UK participation in its preparation was entrusted to Technical Committee CPL/34/3, Auxiliaries for lamps.A list of organizations represented on this committee can be obtained on request to its secretary.Thi

10、s publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 94661 5ICS 29.140.99; 29.140.50Compliance with a British Standard cann

11、ot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN IEC 62386216:2018EUROPEAN STANDARD NORME EUROPENNE EU

12、ROPISCHE NORM EN IEC 62386-216 June 2018 ICS 29.140.50; 29.140.99 English Version Digital addressable lighting interface - Part 216: Particular requirements for control gear - Load referencing (device type 15) (IEC 62386-216:2018) Interface dclairage adressable numrique - Partie 216: Exigences parti

13、culires pour les appareillages de commande - Rfrence de charge (dispositifs de type 15) (IEC 62386-216:2018) Digital adressierbare Schnittstelle fr die Beleuchtung - Teil 216: Anforderungen fr Betriebsgerte - Last-Referenzierung (Gertetyp 15) (IEC 62386-216:2018) This European Standard was approved

14、by CENELEC on 2018-05-28. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national

15、standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own la

16、nguage and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, Fr

17、ance, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Euro

18、pen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN IEC 62386-216:2018 E BS

19、 EN IEC 62386216:2018EN IEC 62386-216:2018 (E) 2 European foreword The text of document 34/491/FDIS, future edition 1 of IEC 62386-216, prepared by IEC/TC 34 “Lamps and related equipment“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 62386-216:2018. The following d

20、ates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2019-02-28 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2021-05-28 Attention is d

21、rawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 62386-216:2018 was approved by CENELEC as a Europ

22、ean Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 61347 (series) NOTE Harmonized as EN 61347 (series). IEC 61347-1 NOTE Harmonized as EN 61347-1. BS EN IEC 62386216:2018EN IEC 62386-216:2018 (E) 3 A

23、nnex ZA (normative) Normative references to international publications with their corresponding European publications The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition

24、cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest ver

25、sions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 62386-101 2014 Digital addressable lighting interface - Part 101: General requirements - System components EN 62386-101 2014 + A11- + A12- IEC 62386-102 2014 Digital addressa

26、ble lighting interface - Part 102: General requirements - Control gear EN 62386-102 2014 + A13- + A14- 1Under preparation. Stage at the time of publication: IEC CCDV 62386-101/AMD1:2018. 2Under preparation. Stage at the time of publication: EN 62386-101:2014/prA1:2017. 3Under preparation. Stage at t

27、he time of publication: IEC CCDV 62386-102/AMD1:2018. 4Under preparation. Stage at the time of publication: EN 62386-102:2014/FprA1:2018. BS EN IEC 62386216:2018This page deliberately left blank 2 IEC 62386-216:2018 IEC 2018 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope 7 2 Normative references 7 3

28、 Terms and definitions 7 4 General . 8 4.1 General . 8 4.2 Version number 8 5 Electrical specification . 8 6 Interface power supply 8 7 Transmission protocol structure . 8 8 Timing . 8 9 Method of operation . 8 9.1 General . 8 9.2 Reference measurement . 8 9.3 Load referencing . 9 9.4 Load deviation

29、 10 9.5 Failure status 10 10 Declaration of variables . 11 11 Definition of commands . 11 11.1 General . 11 11.2 Overview sheets . 11 11.3 Application extended commands . 12 11.3.1 General . 12 11.3.2 Configuration instructions 12 11.3.3 Queries 12 11.4 Special commands 13 11.4.1 General . 13 11.4.2

30、 ENABLE DEVICE TYPE (data) . 13 Bibliography 14 Figure 1 IEC 62386 graphical overview 5 Table 1 Control gear failure status . 10 Table 2 Declaration of variables . 11 Table 3 Application extended commands for this device type . 12 2 IEC 62386-216:2018 IEC 2018 CONTENTS FOREWORD . 3 INTRODUCTION . 5

31、1 Scope 7 2 Normative references 7 3 Terms and definitions 7 4 General . 8 4.1 General . 8 4.2 Version number 8 5 Electrical specification . 8 6 Interface power supply 8 7 Transmission protocol structure . 8 8 Timing . 8 9 Method of operation . 8 9.1 General . 8 9.2 Reference measurement . 8 9.3 Loa

32、d referencing . 9 9.4 Load deviation 10 9.5 Failure status 10 10 Declaration of variables . 11 11 Definition of commands . 11 11.1 General . 11 11.2 Overview sheets . 11 11.3 Application extended commands . 12 11.3.1 General . 12 11.3.2 Configuration instructions 12 11.3.3 Queries 12 11.4 Special co

33、mmands 13 11.4.1 General . 13 11.4.2 ENABLE DEVICE TYPE (data) . 13 Bibliography 14 Figure 1 IEC 62386 graphical overview 5 Table 1 Control gear failure status . 10 Table 2 Declaration of variables . 11 Table 3 Application extended commands for this device type . 12 BS EN IEC 62386216:2018IEC 62386-

34、216:2018 IEC 2018 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ DIGITAL ADDRESSABLE LIGHTING INTERFACE Part 216: Particular requirements for control gear Load referencing (device type 15) FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization

35、comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International

36、Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this

37、preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two or

38、ganizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the fo

39、rm of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpret

40、ation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or r

41、egional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried o

42、ut by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committe

43、es for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to th

44、e Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held

45、 responsible for identifying any or all such patent rights. International Standard IEC 62386-216 has been prepared by IEC technical committee 34: Lamps and related equipment. The text of this International Standard is based on the following documents: FDIS Report on voting 34/491/FDIS 34/513/RVD Ful

46、l information on the voting for the approval of this International Standard can be found in the report on voting indicated in the above table. This document has been drafted in accordance with the ISO/IEC Directives, Part 2. BS EN IEC 62386216:2018 4 IEC 62386-216:2018 IEC 2018 This Part 216 of IEC

47、62386 is intended to be used in conjunction with: Part 101, which contains general requirements for system components; Part 102, which contains general requirements for control gear. A list of all parts in the IEC 62386 series, published under the general title: Digital addressable lighting interfac

48、e, can be found on the IEC website. The committee has decided that the contents of this document will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific document. At this date, the document will be reconfirmed, wi

49、thdrawn, replaced by a revised edition, or amended. IMPORTANT The colour inside logo on the cover page of this document indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a colour printer. BS EN IEC 62386216:2018IEC 62386-216:2018 IEC 2018 5 INTRODUCTION IEC 62386 contains several parts, referred to as series. The 1xx series includes the basic specif