EN 60684-3-247-2011 en Flexible insulating sleeving - Part 3 Specifications for individual types of sleeving - Sheet 247 Heat-shrinkable polyolefin sleeving dual wall not flame ret.pdf

《EN 60684-3-247-2011 en Flexible insulating sleeving - Part 3 Specifications for individual types of sleeving - Sheet 247 Heat-shrinkable polyolefin sleeving dual wall not flame ret.pdf》由会员分享，可在线阅读，更多相关《EN 60684-3-247-2011 en Flexible insulating sleeving - Part 3 Specifications for individual types of sleeving - Sheet 247 Heat-shrinkable polyolefin sleeving dual wall not flame ret.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationFlexible insulating sleevingPart 3: Specifications for individual types of sleeving Sheet 247: Heat-shrinkable polyolefin sleeving, dual wall, not flameretarded, thick and medium

2、 wallBS EN 60684-3-247:2011National forewordThis British Standard is the UK implementation of EN 60684-3-247:2011. It is identical to IEC 60684-3-247:2011.The UK participation in its preparation was entrusted to Technical Commit-tee GEL/15, Solid electrical insulating materials.A list of organizatio

3、ns represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012Published by BSI Standards Limited 2012 ISBN

4、978 0 580 57236 4 ICS 29.035.20 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Stand-ards Policy and Strategy Committee on 31 August 2012.Amendments issued since publicationDate Text affectedBRITISH STAN

5、DARDBS EN 60684-3-247:2011EUROPEAN STANDARD EN 60684-3-247 NORME EUROPENNE EUROPISCHE NORM September 2011 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix

6、17, B - 1000 Brussels 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60684-3-247:2011 E ICS 29.035.20 English version Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 247: Heat-s

7、hrinkable polyolefin sleeving, dual wall, not flame retarded, thick and medium wall (IEC 60684-3-247:2011) Gaines isolantes souples - Partie 3: Spcifications pour types particuliers de gaines - Feuille 247: Gaines thermortractables en polyolfine, double paroi (paisse et moyenne), non retardes la fla

8、mme (CEI 60684-3-247:2011) Isolierschluche - Teil 3: Anforderungen fr einzelne Schlauchtypen - Blatt 247: Wrmeschrumpfende Polyolefinschluche mit Innenbeschichtung, nicht flammwidrig, dickwandig und mittlere Wanddicke (IEC 60684-3-247:2011) This European Standard was approved by CENELEC on 2011-07-2

9、8. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtain

10、ed on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Centra

11、l Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxemb

12、ourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 60684-3-247:2011EN 60684-3-247:2011 - 2 - Foreword The text of document 15/625/FDIS, future edition 1 of IEC 60684-3-247, prepared by IEC TC 15, Solid electri

13、cal insulating materials, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60684-3-247 on 2011-07-28. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible fo

14、r identifying any or all such patent rights. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2012-04-28 latest date by which the national standards conflicting with the EN hav

15、e to be withdrawn (dow) 2014-07-28 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60684-3-247:2011 was approved by CENELEC as a European Standard without any modification. _ BS EN 60684-3-247:2011- 3 - EN 60684-3-247:2011 Annex ZA (normative) Norm

16、ative references to international publications with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced

17、document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD YearIEC 60296 2003 Fluids for electrotechnical applications - Unused mineral insulating oils for

18、 transformers and switchgear EN 60296 + corr. September 2004 2004 IEC 60502-1 2004 Power cables with extruded insulation and their accessories for rated voltages from 1 kV (Um= 1,2 kV) up to 30 kV (Um= 36 kV) - Part 1: Cables for rated voltages of 1 kV (Um= 1,2 kV) and 3 kV (Um= 3,6 kV) - - IEC 6068

19、4-1 2003 Flexible insulating sleeving - Part 1: Definitions and general requirements EN 60684-1 2003 IEC 60684-2 + A2 1997 2005 Flexible insulating sleeving - Part 2: Methods of test EN 60684-2 + A2 1997 2005 IEC 60757 1983 Code for designation of colours HD 457 S1 1985 ISO 846 1997 Plastics - Evalu

20、ation of the action of microorganisms EN ISO 846 1997 ISO 868 2003 Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore hardness) EN ISO 868 2003 ISO 11357-3 1999 Plastics - Differential scanning calorimetry (DSC) - Part 3: Determination of temperature and enth

21、alpy of melting and crystallization - - ISO 11358 1997 Plastics - Thermogravimetry (TG) of polymers - General principles EN ISO 11358 1997 BS EN 60684-3-247:2011 2 60684-3-247 IEC:2011 CONTENTS INTRODUCTION . 5 1 Scope . . 6 2 Normative references. . 6 3 Designation . . 7 4 Conditions of test . 7 5

22、Requirements . 7 6 Sleeving conformance. 7 Annex A (informative) Guide to the available sizes and wall thicknesses . . 12 Table 1 Property requirements 8 Table 2 Requirements for breakdown voltage . 10 Table 3 Resistance to selected fluids 11 Table 4 Additional property requirements . 11 Table A.1 T

23、ype A medium wall 12 Table A.2 Type B thick wall . 12 BS EN 60684-3-247:201160684-3-247 IEC:2011 5 INTRODUCTION This International Standard is one of a series which deals with flexible insulating sleeving for electrical purposes. The series consists of three parts: Part 1: Definitions and general re

24、quirements (IEC 60684-1) Part 2: Methods of test (IEC 60684-2) Part 3: Specifications for individual types of sleeving (IEC 60684-3) This standard gives one of the sheets comprising part 3 as follows: Sheet 247: Heat-shrinkable, polyolefin sleeving, dual wall, not flame retarded, thick and medium wa

25、ll BS EN 60684-3-247:2011 6 60684-3-247 IEC:2011 FLEXIBLE INSULATING SLEEVING Part 3: Specifications for individual types of sleeving Sheet 247: Heat-shrinkable, polyolefin sleeving, dual wall, not flame retarded, thick and medium wall 1 Scope This part of IEC 60684 gives the requirements for two ty

26、pes of heat-shrinkable, polyolefin sleeving, dual wall, not flame retarded with a nominal shrink ratio of 3:1. This sleeving has been found suitable for use at temperatures of up to 100 C. Type A : Medium wall, internal diameter up to 200,0 mm typically Type B : Thick wall, internal diameter up to 2

27、00,0 mm typically These sleevings are normally supplied in colour black. Since these types of sleevings cover a significantly large range of sizes and wall thicknesses, Tables A.1 and A.2 provide a guide to the range of sizes available. The actual size shall be agreed between the user and supplier.

28、Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone.

29、 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60296:2003, Fluids fo

30、r electrotechnical applications Unused mineral insulating oils for transformers and switchgear IEC 60502-1:2004, Power cables with extruded insulation and their accessories for rated voltages from 1 kV (Um= 1,2 kV) up to 30 kV (Um= 36 kV) Part 1: Cables for rated voltages of 1 kV (Um= 1,2 kV) and 3

31、kV (Um= 3,6 kV) IEC 60684-1:2003, Flexible insulating sleeving Part 1: Definitions and general requirements IEC 60684-2:1997, Flexible insulating sleeving Part 2: Methods of test Amendment 2 (2005) IEC 60757:1983, Code for designation of colours ISO 846:1997, Plastics Evaluation of the action of mic

32、ro-organisms ISO 868: 2003, Plastics and ebonite Determination of indentation hardness by means of a durometer (Shore hardness) BS EN 60684-3-247:201160684-3-247 IEC:2011 7 ISO 11357-3:1999, Plastics Differential scanning calorimetry (DSC) Part 3: Determination of temperature and enthalpy of melting

33、 and crystallization ISO 11358:1997, Plastics Thermogravimetry (TG) of polymers General principles 3 Designation The sleeving shall be identified by the following designation: Descrip-tion IEC publication number IEC part number IEC sheet number Type Size (expanded and recovered internal diameter in

34、mm) Colour Table 4* code Sleeving IEC 60684 - 3 - 247 - B - 85,0/25,0 - BK X Any colour abbreviation shall comply with IEC 60757, where applicable. Non-standard colours shall be written out in full. NOTE This information is for package labelling only, in accordance with IEC 60684-1. * The addition o

35、f “X” at the end of the designation indicates that the properties contained in Table 4 have been agreed upon between the user and supplier. 4 Conditions of test Unless otherwise specified, the sleeving shall be shrunk in a forced air circulation oven for (10 1) min at 200 C 3 K prior to testing. 5 R

36、equirements In addition to the general requirements given in IEC 60684-1, the sleeving shall comply with the requirements of Tables 1, 2, 3, and 4 where applicable. 6 Sleeving conformance Conformance to the requirements of this specification shall normally be based on the results from typical sizes:

37、 Type A : Recovered ID 25 mm 30 mm Type B : Recovered ID 25 mm 30 mm BS EN 60684-3-247:2011 8 60684-3-247 IEC:2011 Table 1 Property requirements Property IEC 60684-2 clause or subclause Units Max. or Min. Requirements Remarks Dimensions Internal diameter Wall thickness Concentricity expanded recover

38、ed 3 3.1.2 3.3.2 3.3.3 mm mm % Min. Min. To be agreed between purchaser and supplier 50 85 Heat shock Tensile strength Elongation at break 6 19.1 and 19.2 19.1 and 19.2 - MPa % - Min. Min. 10 200 Heat at 200 C 5 K Jacket only, ignore flowing adhesive Longitudinal change 9 % Max. 10 + 5 Bending at lo

39、w temperature 14 - - No cracking shall be visible. Test at 40 C. For strips, the mandrel shall be between 20 and 22 times the wall thickness. Full section sleeving is tested unfilled and the mandrel shall be between 20 and 22 times the outer diameter. Dimensional stability on storage 16 - - The dime

40、nsions shall remain as agreed. See Clause 1 Scope. Tensile strength Elongation at break 19.1 and 19.2 19.1 and 19.2 MPa % Min. Min. 13 350 Jacket only. Use a jaw separation rate of 100 mm/min. Below 6,5mm as sleeving. At 6,5 mm and above as dumbbells. Secant modulus at 2% elongation 19.4 MPa MPa Min

41、. Max. 80 160 Calculate cross- section area without adhesive. Breakdown voltage 21 kV Min. Table 2 Volume resistivity at room temperature after damp heat 23 23.4.2 23.4.4 m m Min. Min. 10121011 BS EN 60684-3-247:201160684-3-247 IEC:2011 9 Table 1 (continued) Property IEC 60684-2 clause or subclause

42、Units Max. or Min. Requirements Remarks Colour fastness to light Standard identification number 34 Min. The colour standard contrast between the exposed and unexposed parts of the specimen shall be equal to or less than that of the fastness standard. Fastness standard 5 Resistance to selected fluids

43、 Tensile strength Elongation at break 36 19.1 and 19.2 19.1 and 19.2 MPa % Min. Min. 10 250 Use the fluids and test temperatures specified in Table 3. Immersion time (24 1)h Heat ageing Tensile strength Elongation at break 39 19.1 and 19.2 19.1 and 19.2 MPa % Min. Min. 10 200 Heat at 150 C 3 K. Jack

44、et only. Long term ageing Elongation at break 50 19.2 % Min. 175 The ageing temperature shall be 100 C 3 K. Carbon black content ISO 11358 % Min. 2,5 Hardness ISO 868 Shore D Min. 40 Water absorption 40 % Max. 0,5 BS EN 60684-3-247:2011 10 60684-3-247 IEC:2011 Table 1 (continued) Property IEC 60684-

45、2 clause or subclause Units Max. or Min. Requirements Remarks Peel strength 54 N/25 mm Min. Cu 50 Al 75 Pb 40 PE 100 PVC 40 EPR 50 Condition at 150 C 3 K for (10 1) min. For tests in addition to aluminium replace the mandrel with cable jacket material of PE, PVC and/or EPR that conforms to IEC 60502

46、1. See note 2 Melting temperature ISO 11357-3 C Min. 100 Adhesive only NOTE 1 Where jacket only is indicated, the tensile strength calculation for cross-sectional area is based on the thickness of the jacket. NOTE 2 Use a substrate diameter that is a minimum of 25 mm and is at least 20% above the re

47、covered internal diameter of the sleeving. Table 2 Requirements for breakdown voltage Expanded wall thickness mm Expanded ID Dielectric strength akV/mm All dimensions Type A 10-25 26-50 51-120 121 and above Type B 10-25 26-50 51-120 121 and above 14 12 10 8 12 10 8 6 The breakdown voltage shall be d

48、etermined by the method described in 21.4 of IEC 60684-2. The central value shall comply with the minimum value in this table. The sleeving shall be tested in the expanded condition. The rate of application of the voltage shall be 500 V/s. NOTE Care should be taken on selection of sizes based on the

49、se values. Refer to the manufacturer for actual values on installed conditions. aMeasure the expanded jacket wall thickness and calculate the electric strength by dividing the breakdown voltage by this value. BS EN 60684-3-247:201160684-3-247 IEC:2011 11 Table 3 Resistance to selected fluids Test fluid No. Fluids Type Standard or symbol Immersion temperature C 2 K 1 Insulating oil