EN 847-1-2017 en Tools for woodworking - Safety requirements - Part 1 Milling tools circular saw blades.pdf

《EN 847-1-2017 en Tools for woodworking - Safety requirements - Part 1 Milling tools circular saw blades.pdf》由会员分享，可在线阅读，更多相关《EN 847-1-2017 en Tools for woodworking - Safety requirements - Part 1 Milling tools circular saw blades.pdf（40页珍藏版）》请在麦多课文档分享上搜索。

1、Tools for woodworking - Safety requirementsPart 1: Milling tools, circular saw bladesBS EN 8471:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEANSTANDARDNORME EUROPENNE EUROPISCHE NORMEN 847-1November 2017ICS 79.120.10 Supersedes EN 847-1:2013EnglishVersio

2、nTools for woodworking - Safety requirements - Part 1: Milling tools, circular saw bladesOutils pour le travail du bois - Prescriptions de scurit- Partie 1 : Outils de fraisage, lames de scies circulairesMaschinen-Werkzeuge fr Holzbearbeitung -Sicherheitstechnische Anforderungen - Teil1: Frs- und Ho

3、belwerkzeuge, KreissgebltterThis European Standard was approved by CEN on 21 August 2017.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving thisEuropean Standard the status of a national standard without any alteration.Up-to-date lists

4、 and bibliographical referencesconcerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). Aversion in any other language made bytranslation under the

5、responsibility of a CEN member into its own language and notified to the CEN-CENELEC ManagementCentre has the same status as the officialversions.CEN members are the nationalstandards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Re

6、public of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia,Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN D

7、E NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reservedworldwide for CENnational Members.Ref. No. EN 847-1:2017 ENational forewordThis British Standard is the UK implementa

8、tion of EN 847-1:2017. It supersedes BS EN 847-1:2013, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee MTE/23, Woodworking machines.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does

9、not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 94052 1ICS 79.120.10Compliance with a British Standard cannot confer immunity from legal

10、obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 November 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 8471:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 847-1 November 20

11、17 ICS 79.120.10 Supersedes EN 847-1:2013English Version Tools for woodworking - Safety requirements - Part 1: Milling tools, circular saw blades Outils pour le travail du bois - Prescriptions de scurit - Partie 1 : Outils de fraisage, lames de scies circulairesMaschinen-Werkzeuge fr Holzbearbeitung

12、 - Sicherheitstechnische Anforderungen - Teil 1: Frs- und Hobelwerkzeuge, Kreissgebltter This European Standard was approved by CEN on 21 August 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status

13、 of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, Germ

14、an). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia

15、, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey

16、and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref.

17、 No. EN 847-1:2017 EBS EN 8471:2017EN 847-1:2017 (E) 2 Contents Page European foreword . 3 Introduction 4 1 Scope 5 2 Normative references 5 3 Terms, definitions, symbols and abbreviations . 6 3.1 Terms and definitions . 6 3.2 Symbols and abbreviations for cutting materials 11 4 List of significant

18、hazards . 14 5 Design requirements 14 5.1 General requirements for milling tools and circular saw blades . 14 5.2 Special requirements for milling tools for machines with hand feed . 22 6 Tool identification . 28 6.1 Marking of milling tools for integrated feed other than shank mounted tools or inte

19、grated tools . 28 6.2 Marking of milling tools for machines with hand feed other than shank mounted tools or integrated tools 28 6.3 Marking of integrated tools 28 6.4 Marking of shank mounted tools 29 6.5 Marking of tool sets . 29 6.6 Marking of circular saw blades . 30 6.7 Marking of cutting parts

20、 and deflectors . 30 7 Information for use . 31 7.1 General . 31 7.2 Safe working practice . 31 7.3 Maintenance of tools . 32 7.4 Handling 32 Annex A (informative) Maintenance and modification of milling tools and related components 34 A.1 General . 34 A.2 Minimum dimensions . 34 A.3 Retipping, exch

21、ange of tips on composite tools and circular saw blades 34 A.4 Milling tools marked with MAN. 34 A.5 Balance of milling tools 34 A.6 Marking 34 A.7 Information 34 Annex B (normative) Palmqvist Toughness Test. 35 Bibliography . 36 BS EN 8471:2017EN 847-1:2017 (E) 3 European foreword This document (EN

22、 847-1:2017) has been prepared by Technical Committee CEN/TC 142 “Woodworking machines - Safety”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2018,

23、 and conflicting national standards shall be withdrawn at the latest by May 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document super

24、sedes EN 847-1:2013. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of M

25、acedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 8471:2017EN 847-1:2017 (E) 4 Introduction The extent

26、 to which hazards are covered is indicated in the scope of this document. The requirements of this document concern designers, manufacturers, suppliers and importers of tools for cutting wood and materials with similar physical characteristics to wood. This document also includes information that th

27、e manufacturer will provide to the user. BS EN 8471:2017EN 847-1:2017 (E) 5 1 Scope This European Standard specifies all hazards arising from the use of tools for woodworking machines, and describes the methods for the elimination or reduction of these hazards by tool design and by the provision of

28、information. This European Standard deals with milling tools (bore mounted, shank mounted) and circular saw blades, designed for chip removal machining (cutting) of wood and materials with similar physical characteristics to wood, hereinafter referred to as “tools”. The hazards are listed in Clause

29、4. This European Standard does not cover any hazard related to the strength of shank of shank mounted milling tools. This European Standard does not apply to boring bits, eccentric single router cutters, cutters with cutting circle less than 16 mm and to tools used in rotary knife lathes and copying

30、 lathes where the hazard of ejection and contact with the tool is always prevented by a system of fixed guards and/or movable guards interlocked with guard-locking and/or self-closing guards. This European Standard is not applicable for tools according to this scope, which are manufactured before th

31、e date of its publication. NOTE For woodworking machines and materials with similar physical characteristics to wood, see ISO 19085-1. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated

32、 references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 847-2:2017, Tools for woodworking - Safety requirements - Part 2: Requirements for the shank of shank mounted milling tools EN 23878, Hardmetals -

33、 Vickers hardness test (ISO 3878) ISO 286-2, Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts BS EN 8471:2017EN 847-1:2017 (E) 6 3 Terms, definitions, symbols and abbreviatio

34、ns 3.1 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1.1 milling tool rotating cutting tool (e.g. milling cutter, planing cutter, thicknessing cutter) normally having its main feed direction perpendicular to the rotation axis, for working vario

35、us surfaces Note 1 to entry: The cutting edge of the cutting part can be - parallel to the axis of rotation, - square to the axis of rotation, or - a profile which is a combination of the two. The tool can be - a one-piece tool, - a composite tool, - a complex tool, or - in the form of a tool set. 3

36、.1.2 circular saw blade rotating cutting tool for cross-cutting or ripping Note 1 to entry: The tools cut on the periphery and on both flanks simultaneously, and can be - a one-piece tool, - a composite tool, - a complex tool, or - in a form of a stack of circular saw blades with equal diameter. 3.1

37、.3 one-piece tool tool without bonded or detachable parts: the body and the cutting parts are one-piece 3.1.4 composite tool tool where the cutting parts (tips) are firmly connected by bonding to the body, e.g. welding, brazing, adhesive fixing 3.1.5 complex tool tool where one or more cutting parts

38、 are exchangeably mounted in a body through detachable fixing elements Note 1 to entry: The cutting parts can be one-piece or composite. 3.1.6 tool set one or more individual tools (e.g. milling tool, circular saw blade) clamped together on a tool carrier (e.g. sleeve, arbor) designed to function as

39、 one tool BS EN 8471:2017EN 847-1:2017 (E) 7 3.1.7 shank tool tool with integrated shank (e.g. cylindrical, HSK, taper) 3.1.8 integrated tool milling tool where the body is part of the machine and only the cutting parts are exchangeable 3.1.9 body part of the tool which holds the cutting parts or on

40、 which the cutting parts are formed 3.1.10 cutting part functional part or parts of the tool each comprised of chip producing elements Note 1 to entry: The cutting edges, face and flank are therefore elements of the cutting part. In the case of a multi-toothed cutter tool, each tooth has a cutting p

41、art. SOURCE: ISO 3002-1:1982, 3.2.5 3.1.11 auxiliary cutting part additional cutting part with a cutting width of less than or equal to 12 mm and a radial cutting edge projection to the body of less than or equal to 13 mm EXAMPLE Inserts for grooving, edge rounding and chamfering. 3.1.12 spur cuttin

42、g part which operates both on its periphery and on its flank Note 1 to entry: The spur projects from the major cutting edge in radial, and if applicable, in axial direction. A spur is either a separate cutting part (see Figure 1) or a part of the major cutting edge. Dimensions in millimetres Key 1 s

43、crew at the choice of the manufacturer Figure 1 Milling tool with a spur BS EN 8471:2017EN 847-1:2017 (E) 8 3.1.13 cutting diameter d1(cutting radius r1) maximum possible diameter of the cutting edge Note 1 to entry: For tools where various cutting parts can be mounted, d1 is defined by the maximum

44、possible cutting part Note 2 to entry: See Figure 2. key a Shaded area Figure 2 Cutting diameter and cutting width 3.1.14 cutting width b1maximum possible width of the cutting edge Note 1 to entry: For tools where various cutting parts can be mounted, b1 is defined by the maximum possible cutting pa

45、rt Note 2 to entry: See Figure 2. 3.1.15 deflector projecting part exchangeably mounted or firmly connected by bonding to the body or part of the body which performs chip thickness limitation Note 1 to entry: The deflector can also be called a “counter-knife”. Note 2 to entry: See Figures 3 b), 3 c)

46、, 3 d), 3 e) and 3 g). 3.1.16 cutting part projection t difference between the radius r1of the cutting circle and the radius r5of the back supporting circle where t = r1 r5Note 1 to entry: See Figure 3. BS EN 8471:2017EN 847-1:2017 (E) 9 3.1.17 radial cutting edge projection crdifference between the

47、 deflector (not round form tool) or the body (round form tool) and the cutting edge measured in the direction of the normal to the profile Note 1 to entry: See Figures 2 and 3. 3.1.18 axial cutting edge projection cadistance measured axially between the axial cutting edge and the body or the deflect

48、or Note 1 to entry: See Figures 2, 3 a), 3 d) and 3 g) 3.1.19 round form tool tool where the body has a circular shape in any cross section perpendicular to the rotational axis of the tool and which performs chip thickness limitation Note 1 to entry: Auxiliary cutting parts with a deflector or spurs

49、 are not to be considered. Note 2 to entry: See Figure 3 a) 3.1.20 not round form tool tool where chip thickness limitation is performed by a deflector or where the cross section of the body is not circular Note 1 to entry: See Figures 3 b), 3 c), 3 d), 3 e), 3 f) and 3 g) 3.1.21 round form tool set functional unit consisting of a number of individual not round form and/or round form tools clamped together and forming a round form tool with radial gaps of less than 5 mm and axial gaps less than 15 mm and the top and the bottom side is a full r