EN 4301-2009 en Aerospace series - Identification marking methods for engine items - Engineering requirements《航空航天系列 发动机的打印标号 工程要求》.pdf

《EN 4301-2009 en Aerospace series - Identification marking methods for engine items - Engineering requirements《航空航天系列 发动机的打印标号 工程要求》.pdf》由会员分享，可在线阅读，更多相关《EN 4301-2009 en Aerospace series - Identification marking methods for engine items - Engineering requirements《航空航天系列 发动机的打印标号 工程要求》.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 4301:2009ICS 49.050NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAerospace series Identification markingmethods for engineitems EngineeringrequirementsThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 3

2、0 April2009 BSI 2009ISBN 978 0 580 60985 5Amendments/corrigenda issued since publicationDate CommentsBS EN 4301:2009National forewordThis British Standard is the UK implementation of EN 4301:2009.The UK participation in its preparation was entrusted to TechnicalCommittee ACE/12, Aerospace fasteners

3、and fastening systems.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot c

4、onfer immunityfrom legal obligations.BS EN 4301:2009EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 4301March 2009ICS 49.050English VersionAerospace series - Identification marking methods for engineitems - Engineering requirementsSrie arospatiale - Mthodes de marquage pour articlesmoteurs - Exige

5、nces techniquesLuft- und Raumfahrt - Kennzeichnungsverfahren frTriebwerkbauteile - Technische AnforderungenThis European Standard was approved by CEN on 1 March 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStand

6、ard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French,

7、German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech

8、Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE

9、 NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 4301:2009: EBS EN 4301:2009EN 4301:2009 (E) 2 Contents Page Foreword 31 Scope 42 No

10、rmative references 43 Terms and definitions .44 Symbols and abbreviations 55 Arrangement of marks 55.1 General 55.2 General arrangement .56 Coding system .66.1 Identification marking codes 66.2 Standard combinations of identification marks .76.3 Indication on drawings 76.3.1 General 76.3.2 Meaning o

11、f codes given in example (Figure 2) 86.3.3 Understanding Table 3 87 Character height . 128 Writing 129 Depth of marks 1210 General marking conditions 1210.1 Introduction . 1210.2 Process quality . 1210.3 Marking quality 1210.4 Surface treatment . 1310.5 Cast/forged parts 1310.6 Temporary production

12、mark 1310.7 Re-marking 1310.8 Final inspection mark . 1311 Marking methods 1411.1 Permanent markings 1411.2 Temporary markings 15Annex A (normative) Optical Character Recognition (O.C.R.) 17Annex B (normative) Character shapes and optical character recognition requirements (O.C.R.) for 57 dot matrix

13、 method 18Annex C (normative) O.C.R. characters Common characteristics 20BS EN 4301:2009EN 4301:2009 (E) 3 Foreword This document (EN 4301:2009) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in acco

14、rdance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication o

15、f an identical text or by endorsement, at the latest by September 2009, and conflicting national standards shall be withdrawn at the latest by September 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shal

16、l not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Esto

17、nia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 4301:2009EN 4301:2009 (E) 4 1 Scope This standard describes the

18、coding system for marks, the processes used to produce these marks, as well as the general marking requirements for the identification of aerospace engine items. This document is applicable to items whose engineering drawing or design folder refers to EN 4301 for all issues that are not in contradic

19、tion with specific indications appearing on the engineering drawing or in the design folder. This document is not applicable to items requiring an identification plate. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated referen

20、ces, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO 3098-2, Technical product documentation Lettering Part 2: Latin alphabet, numerals and marks (ISO 3098-2:2000) 3 Terms and definitions For the purpose

21、s of this document, the following terms and definitions apply. 3.1 marking action of affixing one or more marks on a medium 3.2 mark physical information, composed of legible characters on the item or its packaging 3.3 permanent mark mark produced by means of a marking process whose characters can o

22、nly be eliminated by removing material (machining) 3.4 temporary mark mark produced by means of a marking process whose characters can be easily removed 3.5 character each of the elements which compose the mark: letter, figure, symbol, separator, etc. 3.6 design authority person or corporate body wh

23、o is in charge of the design definition 3.7 design definition creative activity which, starting from expressed needs, existing means, and technological possibilities, results in the design of a product meeting these needs and industrially feasible BS EN 4301:2009EN 4301:2009 (E) 5 3.8 manufacturer p

24、erson or corporate body who masters the design of a product and has complete control over the quality of each item or sample produced 3.9 supplier person or corporate body party to a business venture, contract, or order they have accepted which commits them, with respect to the customer, to carrying

25、 out the provisions stated therein 3.10 production source person or corporate body who is responsible, with respect to the manufacturer, for manufacturing and inspecting a cast or forged, pre-machined, finished item or material. This may involve a subcontractor or an accessory manufacturer. To the e

26、xtend that he is given the order, he becomes a producer 3.11 subcontractor person or corporate body who carries out, on behalf of and under the responsibility of a supplier, all or part of the business venture, contract, or order concluded by the customer NOTE In the case of Public Contracts, a sing

27、le subcontractor is not allowed to execute the entire contract entered into by the customer. 4 Symbols and abbreviations O.C.R. Optical Character Recognition 5 Arrangement of marks 5.1 General Marks are to be made in the same order as that shown by the combinations for the standard arrangements (alp

28、habetical code) identified by numerical codes given in Table 2 or in accordance with a particular combination indicated in the note on the drawing. 5.2 General arrangement character height = h; minimum distance between two marks on the same line: 3 h; minimum distance between two successive lines: 1

29、,4 h; first character on all lines: aligned on the left; any marking placed to the right of the manufacturers identification number should be at a distance of at least 15 mm from it. BS EN 4301:2009EN 4301:2009 (E) 6 EXAMPLE 2 10 3 1 h 1,4 h 3 h2 : Company code (Designer) 1 : Item identification num

30、ber 10 : Production sources company code 3 : Serialization number 6 Coding system 6.1 Identification marking codes Identification marking is in accordance with codes specified in Table 1. Table 1 Code Marking Comments 1 Item identification number Determined by the manufacturer and indicated in desig

31、n documents, with change letter if applicable. 2 Company code (designer) Manufacturers or designers company code indicated in items design documents. 3 Serialization number 4 Production batch number 5 Material batch number 6 Production sources company monogram For small-sized items, can replace prod

32、uction sources company code. Manufacturer must keep the list of producer monograms up to date. 7 Curing date For elastomer only, should be indicated as follows: year and quarter: 2Q95 or 2T95. 8 Casting number For foundry only 9 Manufacturing date With five characters unless otherwise indicated in d

33、esign documents. Should be shown as follows: year and week (recommended): 95W26 or year and month: 9506. 10 Production sources company code 11 Additional markings Indicated in design documents. Inspection marking As this marking is systematic, it is not codified. Concession marking As this informati

34、on does not appear in the design documents, it is not codified. BS EN 4301:2009EN 4301:2009 (E) 7 6.2 Standard combinations of identification marks Standard combination is in accordance with codes specified in Table 2. Table 2 Code Combination Comments A 2 1 10 3 (1 line) 3 is replaced by 9 for non-

35、serialized items B 2 1 10 3 (2 lines) C 2 1 10 3 (4 lines) D 2 1 3 9 7 E 2 1 9 F 2 1 3 9 G 1 3 9 H 1 9 J 2 1 9 7 6.3 Indication on drawings 6.3.1 General Codes for the marks to be made, usable marking processes, and notes if needed, are shown in a symbol (see Figure 1) placed on the drawing. Marking

36、 processes or the process family (see Table 3) are preceded by the identification number of this standard, both separated by a dash. The note or notes are optional and are written out in full on the drawing near the symbol or the title block and designated by one or more numbers. MARKING Code combin

37、ation MARKING Code combination B Process(es) EN4301 Process(es)EN4301-02F2 Note(s) Note(s) 1 2 Figure 1 Symbol Figure 2 Example of codified symbol BS EN 4301:2009EN 4301:2009 (E) 8 6.3.2 Meaning of codes given in example (Figure 2) B : Marking arrangement on two lines (in accordance with combination

38、 in Table 2 and rules in 5.1). 02F2 : “Dots“ marking process, depth of markings 0,03 mm to 0,10 mm (see Table 3). 6.3.3 Understanding Table 3 Examples of writing on drawing InterpretationEN4301-02 : Permits each of the marking processes in the second column (02A to 02F) or each of the processes in t

39、he third column (02A1 to 02F3). EN4301-02C : Permits marking processes 02C1 or 02C2. EN4301-02B1 : Permits the “shallow press“ marking process. EN4301-B : Permits each of the processes marked with an “X“ in column B.EN4301-02B1-D : Permits the 02B1 marking process and each of the processes markedwit

40、h an “X“ in column D. EN4301-02B-DM5 : Permits the 02B marking process with a character height of 3,20 mm, O.C.R. writing. BS EN 4301:2009EN 4301:2009 (E) 9 Table 3 Marking method codes, class letter and depth Method code Compatibility O.C.R. Marking method See Clause 11. Depth (mm) Marking class le

41、tter 1sttier 2ndtier 3rdtier min. max. A B C D E F G H J K L M N P R Permanent marking methods 01 Integral 01A light 01A1 raised 0,13 0,25 X 01A2 depressed 0,13 0,25 X 01B intermediate 01B1 raised 0,20 0,89 01B2 depressed 0,20 0,89 01C heavy (raised only) 0,8 3,3 02 Metal stamp 02A X Hamer 02A1 X sh

42、allow 0,03 0,15 X 02A2 X deep 0,10 0,25 X X 02B X Pres 02B1 X shallow 0,03 0,15 X X 02B2 X deep 0,10 0,25 X X X 02C Rol 02C1 shallow 0,03 0,15 X X X X X 02C2 deep 0,10 0,25 X X X 02D Vibro peen, manual 02D1 shallow 0,03 0,15 X X X X 02D2 deep 0,10 0,25 X X X 02E Vibro peen, controlled 02E1 shallow L

43、egible 0,05 X 02E2 deep 0,05 0,15 X X X X X 02F X Dot-peening matrix mode (57) 02F1 X shallow Legible 0,05 02F2 X intermediate 0,03 0,10 X X X 02F3 X deep 0,05 0,15 X X X X X X BS EN 4301:2009EN 4301:2009 (E) 10 Table 3 (continued) Method code Compatibility O.C.R. Marking method See Clause 11. Depth

44、 (mm) Marking class letter 1sttier 2ndtier 3rdtier min. max. A B C D E F G H J K L M N P R Permanent marking methods 03 Engrave 03A manual 0,013 0,15 X X 03B controlled 03B1 shallow 0,013 0,08 X X X 03B2 deep 0,05 0,15 X X X X X X 07 Electrochemical 07A Etch 07A1 shallow Legible 0,008 X X 07A2 inter

45、mediate 0,008 0,038 X X X X X 07A3 deep 0,03 0,08 X 07B Deposit raised Legible 0,010 X 07C AC etch 07C1 shallow Legible 0,008 X X 07C2 intermediate 0,008 0,038 X X X X X 07C3 deep 0,03 0,08 X 07D AC etch DC deposit Legible 0,013 X 08 Blast 08A shallow Legible 0,013 X X 08B intermediate 0,008 0,03 X

46、X X X 08C deep 0,03 0,08 X X X X X 09 Brand 0,03 0,25 09A hot press 0,03 0,25 10 Ceramic 11 Decalcomania 13 Band 14 Pressure sensitive label BS EN 4301:2009EN 4301:2009 (E) 11 Table 3 (concluded) Method code Compatibility O.C.R. Marking method See Clause 11. Depth (mm) Marking class letter 1sttier 2

47、ndtier 3rdtier min. max. A B C D E F G H J K L M N P R Permanent marking methods 15 Laser 15A X Dot matrix mode (57) 15A1 X shallow 0,003 0,008 15A2 X intermediate 0,010 0,03 15A3 X deep 0,03 0,08 15B Engrave mode 15B1 shallow 0,003 0,015 15B2 intermediate 0,018 0,10 15B3 deep 0,10 0,25 16 Plastic laminate 29 Any temporary method 30 Ink 31 Dye 32 Paint 32A silk-screen 33 Chalk 34 Crayon 35 Tag 35A non-metallic tag and string X 35B non-metallic tag and wire X 35C metallic tag and wi