EN 2467-2007 en Aerospace series - Steel FE-PA3901 (X2CrNi18-9) - Air melted - Softened - Plate sheet and strip - 0 4 mm less than or equal to a less than or equal to 20 mm - 520 M.pdf

《EN 2467-2007 en Aerospace series - Steel FE-PA3901 (X2CrNi18-9) - Air melted - Softened - Plate sheet and strip - 0 4 mm less than or equal to a less than or equal to 20 mm - 520 M.pdf》由会员分享，可在线阅读，更多相关《EN 2467-2007 en Aerospace series - Steel FE-PA3901 (X2CrNi18-9) - Air melted - Softened - Plate sheet and strip - 0 4 mm less than or equal to a less than or equal to 20 mm - 520 M.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 2467:2007Aerospace series Steel FE-PA3901 (X2CrNi18-9) Air melted Softened Plate, sheet and strip 0,4 mm u a u 20 mm 520 MPa u Rm u 670 MPaICS 49.025.10g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g

2、51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 2467:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2008 BSI 2008ISBN 978 0 580 56576 2National forewordThis British Standard is the UK implementatio

3、n of EN 2467:2007.The UK participation in its preparation was entrusted by Technical Committee ACE/61, Metallic materials for aerospace purposes, to Panel ACE/61/-/15, Steels.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not p

4、urport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since publicationDate CommentsEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NOR

5、M EN 2467 August 2007 ICS 49.025.10 English Version Aerospace series - Steel FE-PA3901 (X2CrNi18-9) - Air melted -Softened - Plate, sheet and strip - 0,4 mm a 20 mm - 520 MPa Rm 670 MPa Srie arospatiale - Acier FE-PA3901 (X2CrNi18-9) - labor lair - Adouci - Plaques, tles et bandes - 0,4 mm a 20 mm -

6、 520 MPa Rm 670 MPa Luft- und Raumfahrt - Stahl FE-PA3901 (X2CrNi18-9) - Lufterschmolzen - Weichgeglht - Platten, Bnder und Bleche - 0,4 mm a 20 mm - 520 MPa Rm 670 MPaThis European Standard was approved by CEN on 23 June 2007. CEN members are bound to comply with the CEN/CENELEC Internal Regulation

7、s which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This Europ

8、ean Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the nat

9、ional standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and

10、 United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2467:

11、2007: E2 Foreword This document (EN 2467:2007) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National

12、 Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2008, and conflicting national st

13、andards shall be withdrawn at the latest by February 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELE

14、C Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembou

15、rg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 2467:20073 Introduction This standard is part of the series of EN metallic material standards for aerospace applications. The general organization of this series is

16、 described in EN 4258. This standard has been prepared in accordance with EN 4500-5. 1 Scope This standard specifies the requirements relating to: Steel FE-PA3901 (X2CrNi18-9) Air melted Softened Plate, sheet and strip 0,4 mm a 20 mm 520 MPa Rm 670 MPa for aerospace applications. 2 Normative referen

17、ces The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2951, Aerospace series Metallic materials

18、Test method Micrographic determination of content of non-metallic inclusions.1)EN 4258, Aerospace series Metallic materials General organization of standardization Links between types of EN standards and their use. EN 4500-5, Aerospace series Metallic materials Rules for drafting and presentation of

19、 material standards Part 5: Specific rules for steels. 1) EN 4700-1, Aerospace series Steel and heat resisting alloy Wrought products Technical specification Part 1: Plate, sheet and strip. 1) 1) Published as ASD Prestandard at the date of publication of this standard. BS EN 2467:20074 1 Material de

20、signation Steel FE-PA3901 (X2CrNi18-9) Element C Si Mn S aP aCr aNi aFe min. 17,5 8 2 Chemical composition % max. 0,030 1 2 0,015 0,045 19,5 10 Base 3 Method of melting Air melted 4.1 Form Plate, sheet and strip 4.2 Method of production Rolled 4.3 Limit dimension(s) mm 0,4 a 20 5 Technical specifica

21、tion EN 4700-1 Delivery condition Softened 6.1 Heat treatment 1 000 C 1 100 C WQ/AQ 6.2 Delivery condition code U Use condition Delivery condition 7 Heat treatment Characteristics 8.1 Test sample(s) See EN 4700-1. 8.2 Test piece(s) See EN 4700-1. 8.3 Heat treatment Delivery condition 9 Dimensions co

22、ncerned mm 0,4 a 6 6 1,67 %; - S + P + B should be 0,025 %. 99 Typical use BS EN 2467:20076 100 Product qualification See EN 4700-1. Qualification programme to be agreed between manufacturer and purchaser. BS EN 2467:2007blankBS EN 2467:2007BSI Group Headquarters389 Chiswick High Road,London W4 4AL,

23、 UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards Institute (BSI)BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are u

24、pdated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this Briti

25、sh Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000 Fax: +44 (0)20 8996 7400BSI offers members an individual updating service called PLUS which ensures that subscribers automatically rec

26、eive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit card from the BSI Shop on the W

27、ebsite http:/ response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international

28、standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members

29、of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to Brit

30、ish Standards via British Standards Online can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as p

31、ermitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the cou

32、rse of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070 Email: