EN 13413-2001 en Resilient Floor Coverings - Polyvinyl Chloride Floor Coverings on a Filled Fibrous Backing - Specification《弹性地板覆盖物 填充纤维底板上的聚氯乙烯地面覆盖物 规范》.pdf

《EN 13413-2001 en Resilient Floor Coverings - Polyvinyl Chloride Floor Coverings on a Filled Fibrous Backing - Specification《弹性地板覆盖物 填充纤维底板上的聚氯乙烯地面覆盖物 规范》.pdf》由会员分享，可在线阅读，更多相关《EN 13413-2001 en Resilient Floor Coverings - Polyvinyl Chloride Floor Coverings on a Filled Fibrous Backing - Specification《弹性地板覆盖物 填充纤维底板上的聚氯乙烯地面覆盖物 规范》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD Resilient floor coverings Polyvinyl chloride floor coverings on a filled fibrous backing Specification The European Standard EN 13413:2001 has the status ofa British Standard ICs 97.150 BS EN 1341 3:2002 Wk present to the responsible European committee any enquiries on the interpret

2、ation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. - A list of organizations represented on this committee can be obtained on request to its secretary. Cr oss-r e fer enc e s The British Standards

3、 which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard do

4、es not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an ins

5、ide front cover, the EN title page, pages 2 to 9 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. O BSI 5 March 2002 ISBN0 580 39212 O EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13413 December 2001 ICs 97.150 English version R

6、esilient floor coverings - Polyvinyl chloride floor coverings on a filled fibrous backing - Specification Revtements de sol rsilients - Revtements de sol base de polychlorure de vinyle sur semelle en fibre minrale - Spcifications Elastische Bodenbelge - Polyvinylchlorid-Bodenbelge mit einem Rcken au

7、s Fasermaterial - Spezifikationen This European Standard was approved by CEN on 4 November 2001 CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-da

8、te lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the r

9、esponsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, N

10、etherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION EUROPISCHES KOMITEE FR NORMUNG COMIT EUROPEN DE NORMALISATION Management Centre: rue de Stassart, 36 B-1050 Brussels O 2001 CEN All rights of exploitation in any form and by any means

11、reserved worldwide for CEN national Members. Ref. No. EN 13413:2001 E EN 13413:2001 (E) Foreword This European Standard has been prepared by Technical Committee CEN /TC 134, “Resilient and textile floor coverings“, the secretariat of which is held by BSI. This European Standard shall be given the st

12、atus of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2002, and conflicting national standards shall be withdrawn at the latest by June 2002. Annexes A and B are informative. According to the CENKENELEC Internal Regulations, the national sta

13、ndards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. 2 EN 1341

14、3:2001 (E) 1 Scope This European Standard specifies the characteristics of floor coverings with compact surface layers, made of polyvinyl chloride and modifications thereof, on a filled fibrous backing and supplied in roll form. To encourage the consumer to make an informed choice, the standard incl

15、udes a classification system (see EN 685) based on intensity of use, which shows where these floor coverings should give satisfactory service. It also specifies requirement for marking. 2 Normative References This European Standard incorporates by dated or undated reference, provisions from other pu

16、blications. These normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or rev

17、ision. For undated references the latest edition of the publication referred to applies (including amendments). EN 424, Resilient floor coverings - Determination of the effect of simulated movement of a furniture leg. EN 425, Resilient floor coverings - Determination of the effect of a castor chair.

18、 EN 426, Resilient floor coverings - Determination of width, length, straightness and flatness of sheet material. EN 428, Resilient floor coverings - Determination of overall thickness. EN 429, Resilient floor coverings - Determination of the thickness of layers. EN 430, Resilient floor coverings -

19、Determination of mass per unit area. EN 432, Resilient floor coverings - Determination of shear force. EN 433, Resilient floor coverings - Determination of residual indentation after static loading. EN 434, Resilient floor coverings -Determination of dimensional stability and curling after exposure

20、to heat. EN 435, Resilient floor coverings - Determination of flexibility. EN 660-1, Resilient floor coverings - Determination of wear resistance - Part I: Stuttgart test. EN 660-2, Resilient floor coverings - Determination of wear resistance - Part 2: Frick-Taber test. EN 661, Resilient floor cover

21、ings - Determination of the spreading of water. EN 684, Resilient floor coverings - Determination of seam strength. EN 685, Resilient floor coverings - Classification. EN 12466, Resilient floor coverings - Vocabulary. EN IS0 105-B02, Textiles - Tests for colour fastness - Part 602: Colour fastness t

22、o artificial light: Xenon arc fading lamp test (IS0 105-602: 1994, including Amendment I: 1998). 3 EN 13413:2001 (E) 3 Terms and definitions For the purposes of this European Standard, the terms and definitions of EN 12466 and the following terms and definitions apply: 3.1 fil led fi brous backing a

23、 backing made in a wet process, predominantly from mineral fillers, as well as synthetic and natural fibres (non- asbestos formulated), binders, and which is suitable for use as a support for floor covering 3.2 polyvinyl chloride floor covering on a filled fibrous backing floor covering consisting o

24、f polyvinyl chloride surface layer applied to a filled fibrous backing 4 Requirements 4.1 General requirements Polyvinyl chloride floor coverings described in this standard shall conform with the appropriate general requirements specified in Table 1, when tested in accordance with the methods given

25、therein. 4.2 Classification Requirements 4.2.1 Wear group classification Floor coverings described in this standard shall be classified in the appropriate wear group specified in Table 2, .e. in group T, P, M, when tested in accordance with EN 660-1 or EN 660-2. NOTE The tests are intended to determ

26、ine the wear resistance of wear layers defined either by thickness loss (EN 660-1) or volume loss (EN 660-2). Floor coverings with a transparent wear layer are a priorigroup T and need not be tested. 4.2.2 Level of use classification Floor coverings described in this standard shall be classified as

27、suitable for different levels of use in accordance with the performance requirements specified in Table 3, when tested with the methods given therein. Classification shall conform to the scheme established in EN 685. 4 EN 13413:2001 (E) Property Table 1 - General Requirements Requirements length m w

28、idth mm Overall thickness mm Average Individual resu Its Total mass g/m2 per unit area (average) Residual indentation mm (average) Dimensional stability % not less than the nominal value not less than the nominal value Nominal value + 0,18 Nominal value f 0,20 Nominal value +I3 % -10% - 0,15 Average

29、 value 0,2 0,4 Curling after exposure to heat ) Colour fastness to artificial light Shear force of backing N Spreading of water Flexibility 6 minimum Average 2 360 No individual value 280 Time for water to spread to one edge of test piece 2 16 h Test using a 20 mm mandrel. For products that show sig

30、ns of cracking, perform a further test using a 40 mm mandrel. If results show no further cracking record the use of a 40 mm diameter mandrel Test Method EN 426 Property EN 428 EN 430 Wear class Test method EN 433 Thickness loss A/ mm Volume loss Fv mm EN 434 T P M F A/ 0,08 0,08 A/ 0,15 0,15 A/ 0,30

31、 0,30 A/ 0,60 EN 660-1 Fv 2,O 2,O Fv 4,O 4,O Fv 7,5 7,5 Fv 15,O EN 660-2 EN IS0 105-BO2 : Method 3 EN 432 EN 661 EN 435 Method A ) The test needs only to be carried out for products which are to be laid unbonded needs not be carried out for fully bonded materials. 2, Expose a full size test sample.

32、Store a further test sample in the dark, which will standard for the assessment of colour change. to the subfloor. The test constitute the reference 5 EN 13413:2001 (E) Table 3 - Classification requirements for level of use Class Symbol Level of use -rr Test method commercial heavy industrial genera

33、l commercial very heavy industrial heavy ) The average shall be the nominal value . Thickness of wear layer mm 1 Nrr T 0,15 - - 0,20 - 0,30 - 0,40 - 0,55 0,70 - 3% al valu P 0,25 0,35 0,45 0,55 0,70 1 ,o0 IN 429 - M 0,40 - - 0,50 - 0,65 - 0,80 - 1 ,o0 - 1,50 - Effect of a castor chair No requirement

34、 If tested, no disturbance to the surface other than slight change in appearance and no delamination shall occur EN 425 At not more than 0,l mm. Seam strength N150 mm No requirement When welded in accordance with the man ufact u re rs Instructions: average value: 2 240 individual values 2 180 EN 684

35、 Simulated movement of a furniture leg No requirement No damage shall be visible when tested with a type 3 foot. No damage shall be visible when tested with a foot type 2 When welded in accordance with manufacturers instructions: no damage shall be visible to seams when tested with a type O foot :N

36、424 -10 % No individual value shall exceed 0,5 mm or 15 % below the nominal, whichever is the greater. 5 Marking Floor coverings described in this standard and/or their packaging shall bear the following marking: a) b) manufacturers or suppliers identification; c) product name; d) colour/pattern and

37、 batch and roll number; e) classes/symbols appropriate for the product; f) length, width, thickness; g) number and date of the European Standard .e. EN 13413:2001; statement regarding method of bonding. Cleaning and maintenance instructions shall be delivered together with the product. 6 EN 13413:20

38、01 (E) Annex A ( i nf o rma t ive) Optional properties Where the following properties are required for specific applications, the floor covering should be tested in accordance with the appropriate methods. - electrical resistance (EN 1081); - electrostatic propensity (EN 1815); - effect of stains (E

39、N 423); - heavy swivel castor (EN 181 8). 7 EN 13413:2001 (E) Annex B (informative) Additional methods of test The following test methods are also available for this type of products but do not form part of the specification: - curling on exposure to moisture (EN 662); - conventional pattern depth (

40、EN 663); - volatile loss (EN 664); - exudation of plasticisers (EN 665); - gelling (EN 666); - masshnit area of a reinforcement backing (EN 718); - determination of peel resistance (EN 431). 8 EN 13413:2001 (E) Bibliography EN 423, Resilient floor coverings - Determination of resistance to staining.

41、 EN 431, Resilient floor coverings - Determination of peel resistance. EN 662, Resilient floor coverings - Determination of curling on exposure to moisture. EN 663, Resilient floor coverings - Determination of conventional pattern depth. EN 664, Resilient floor coverings - Determination of volatile

42、loss. EN 665, Resilient floor coverings - Determination of exudation of plasticizers. EN 666, Resilient floor coverings - Determination of gelling. EN 718, Resilient floor coverings - Determination of mass per unit area of a reinforcement or a backing of polyvinyl chloride floor coverings. EN 1081,

43、Resilient floor coverings - Determination of electrical resistance. EN 1 81 5, Resilient and textile floor coverings - Assessment of static electrical propensity. EN 181 8, Resilient floor coverings - Determination of the effect of loaded heavy duty castors. 9 BS EN 1341 3:2002 BSI 389 Chiswick High

44、 Road Lon don w4 4AL BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Re vi si ons British Standards are updated by amendment or revision. Users of Bri

45、tish Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of th

46、e technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Bu

47、ying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: orders&-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for internatio

48、nal standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technic

49、al Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 71 11. Fax: +44 (0)20 8996 7048. Email: infomi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details ofthese and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 700 1. Email: membershipb