DLA SMD-5962-89595 REV B-2005 MICROCIRCUIT HYBRID LINEAR 12-BIT ANALOG-TO-DIGITAL CONVERTER《12位模拟数字转变器 线性混合微型电路》.pdf

《DLA SMD-5962-89595 REV B-2005 MICROCIRCUIT HYBRID LINEAR 12-BIT ANALOG-TO-DIGITAL CONVERTER《12位模拟数字转变器 线性混合微型电路》.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-89595 REV B-2005 MICROCIRCUIT HYBRID LINEAR 12-BIT ANALOG-TO-DIGITAL CONVERTER《12位模拟数字转变器 线性混合微型电路》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Made changes to table I. Updated document. Editorial changes throughout. 93-06-05 K. A. Cottongim B Updated drawing to reflect the latest requirements. -sld 05-07-29 Raymond Monnin The original first page of this drawing has been replaced REV SHE

2、ET REV SHEET REV STATUS REV B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Donald R. Osborne DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Robert M. Heber COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil/ THIS DRAWING IS AVAILAB

3、LE FOR USE BY ALL DEPARTMENTS APPROVED BY William K. Heckman MICROCIRCUIT, HYBRID, LINEAR, 12-BIT, ANALOG-TO-DIGITAL CONVERTER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 90-05-08 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-89595 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962

4、-E425-05 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89595 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describe

5、s device requirements for class H hybrid microcircuits to processed in accordance with MIL-PRF-38534. 1.2 PIN. The PIN shall be as shown in the following example: 5962-89595 01 X X Drawing number Device type Case outline Lead finish (see 1.2.1) (see 1.2.2) (see 1.2.3) 1.2.1 Device type(s). The devic

6、e type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 MN5245 12-bit, A/D converter, 0 to +5 V dc 02 MN5245A 12-bit, A/D converter, 0 to +5 V dc, 3-state outputs 03 MN5246 12-bit, A/D converter, 2.5 V dc 04 MN5246A 12-bit, A/D converter, 2.5 V dc, 3-state

7、outputs 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 40 Dual-in-line Y See figure 1 40 Leadless dual-in-line 1.2.3 Lead finish. The lead finish shall be as specified in MIL-PR

8、F-38534. 1.3 Absolute maximum ratings. 1/ Positive supply voltage range (VCC) . -0.5 V dc to +18 V dc Negative supply voltage range (VEE) +0.5 V dc to -18 V dc Logic supply voltage range (VDD) . -0.5 V dc to +7 V dc Analog input channel range -1 V dc to +6 V dc Digital input range -0.5 V dc to +5.5

9、V dc Power dissipation (PD) 2.925 W Thermal resistance: Junction-to-case (JC). 7.8C/W Junction-to-ambient (JA) 25C/W Lead temperature (soldering, 10 seconds). +300C Storage temperature range -65C to +150C Junction temperatgure (TJ). +175C 1/ Stresses above the absolute maximum ratings may cause perm

10、anent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89595 DEFENSE SUPPLY CENTER COLUMBUS COLUMB

11、US, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.4 Recommended operating conditions. Positive supply voltage range (VCC) . +14.55 V dc to +15.45 V dc Negative supply voltage range (VEE) -14.55 V dc to -15.45 V dc Logic supply voltage range (VDD) . +4.75 V dc to +5.25 V dc Convers

12、ion rate 1.1 MHz Ambient operating temperature range (TA). -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the i

13、ssues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electron

14、ic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standar

15、dization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes

16、applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38534 and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and p

17、hysical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics.

18、Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWI

19、NG SIZE A 5962-89595 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I.

20、 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-3853

21、4, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for tho

22、se which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DSCC-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order

23、to supply to this drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be

24、 provided with each lot of microcircuits delivered to this drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89595 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC

25、 FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits Unit Test Symbol Conditions 1/ -55C TA+125C unless otherwise specified Group A subgroups Device type Min Max Analog inputs Unipolar 01,02 0 +5 Input voltage range VIN Bipolar 1,2,3 03,04 -2.5 +2.5 V Input impedance ZINTA= +25C

26、 2/ 4 All 25/40 k/pF Digital inputs Input voltage high VIH Logic “1“ (for all digital inputs) +2.0 Input voltage low VILLogic “0“ (for all digital inputs) +0.8 V Input current high IIH VIH= +2.7 V +20 A Input current low IIL VIL= -0.4 V 1,2,3 All -0.4 mA Transfer characteristics Integral linearity e

27、rror LE -1 +1 Differential linearity error DLE -1 +2 LSB No missing codes NMC 1,2,3 All Pass 1 -0.15 +0.15 Full scale absolute accuracy error FSE 2,3 All -0.3 +0.3 %FSR 1 -0.1 +0.1 Unipolar offset error UOE 2,3 01,02 -0.15 +0.15 %FSR Unipolar offset error drift UOE T TA= -55C and +125C01,02 8 -20 +2

28、0 FSRofppmCSee footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89595 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I.

29、 Electrical performance characteristics - Continued. Limits Test Symbol Conditions 1/ -55C TA+125C unless otherwise specified Group A subgroups Device type Min Max Unit Transfer characteristics - Continued. 1 -0.2 +0.2 Bipolar offset error BOE 2,3 03,04 -0.5 +0.5 % 1 -0.1 +0.1 Bipolar zero error BZE

30、 2,3 03,04 -0.2 +0.2 %FSR Bipolar zero error drift BZE T TA= -55C and +125C 8 03,04 -25 +25 FSRofppmC4 -0.1 +0.1 Gain error AE 5,6 All -0.3 +0.3 % Gain error drift AE T TA= -55C and +125C 5,6 All -40 +40 ppm/ C Digital outputs Output voltage high VOHIOH= +200 A All +2.7 Output voltage low VOLIOL= -2

31、.0 mA All +0.4 V IOZHVOH= +2.7 V 02,04 +10 3-state leakage current IOZLVOL= -0.4 V 1,2,3 02,04 -10 A Dynamic characteristics Conversion time tc 9,10,11 All 900 ns Pulse width (start convert) tPW9,10,11 All 50 ns See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networkin

32、g permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89595 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Conditions 1/ -55C TA+125C

33、unless otherwise specified Group A subgroups Device type Min Max Unit Dynamic charateristics - Continued. Delay (falling edge of start to status = “1“) tD19,10,11 All 60 ns Delay (falling edge of start to previous output data invalid) tD22/ 9,10,11 All 700 ns Delay (falling edge of status to output

34、data valid) tD32/ 9,10,11 All 0 ns Delay (falling edge of enable to output data valid) tD49,10,11 All 70 ns EOC pulse width pWTA= +25C 9 All 850 ns T2 time t2TA= +25C 9 All 760 ns T2 pulse width pWt2TA= +25C 9 All 90 120 ns Reference output Internal reference: Voltage Range VREF TA= +25C 1 All +4.9

35、+5.1 V Drift VREFTA= -55C and +125C 2,3 All 25 ppm/ C External current IREFTA= +25C 1 All 5 A Power supply Supply currents: +15 V supply (VCC) ICC1,2,3 All +50 mA 1 -90 -15 V supply (VEE) IEE2,3 2/ All -95 mA +5 V supply (VDD) IDD1,2,3 All +165 mA See footnotes at end of table. Provided by IHSNot fo

36、r ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89595 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Tes

37、t Symbol Conditions 1/ -55C TA+125C unless otherwise specified Group A subgroups Device type Min Max Unit Power supply - Continued. Power dissipation PD1,2,3 All 2925 mW 1 -50 Power supply rejection ratios: +15 V supply (VCC) PSSR1 2,3 2/ All -50 dB 1 -50 -15 V supply (VEE) PSSR2 2,3 2/ All -50 dB 1

38、 -50 +5 V supply (VDD) PSSR3 2,3 2/ All -50 dB 1/ +14.55 V dc VCC +15.45 V dc, -14.55 V dc VEE -15.45 V dc, +4.75 V dc VDD +5.25 V dc, unless otherwise specified. 2/ Parameter shall be tested as part of device intial characterization and after design and process changes. Parameter shall be guarantee

39、d to the limits specified in table I for all lots not specifically tested. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89595 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET

40、 9 DSCC FORM 2234 APR 97 Case X Inches mm Inches mm .002 .008 .010 .013 .018 .025 .085 .100 .115 .142 0.05 0.20 0.25 0.33 0.46 0.64 2.16 2.54 2.92 3.61 .182 .200 .230 .600 .770 .810 1.900 2.074 2.116 4.62 5.08 5.84 15.24 19.56 20.50 48.26 52.68 53.75 FIGURE 1. Case outline(s). Provided by IHSNot for

41、 ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89595 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 10 DSCC FORM 2234 APR 97 Case Y Inches mm Inches mm .005 .050 .065 .085 .087 .100 .110 0.13 1.27

42、 1.65 2.16 2.21 2.54 2.74 .115 .159 .780 .800 2.074 2.116 2.92 4.04 19.81 20.32 52.68 53.75 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .005 (0.13 mm). FIGURE 1. Case outline(s) - Continued.Provided by

43、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89595 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 11 DSCC FORM 2234 APR 97 Device types All Device types All Case outlines X and Y Case

44、outlines X and Y Terminal number Terminal symbol Terminal number Terminal symbol 1 Analog input 21 Test point 2 Analog ground 22 VDD3 VEE23 Bit 12 (LSB) 4 Test point 24 Bit 11 5 Test point 25 Bit 10 6 N/C 26 Bit 9 7 Analog ground 27 Bit 8 8 N/C 28 Bit 7 9 VCC 29 Bit 6 10 N/C 30 Bit 5 11 Digital grou

45、nd 31 Bit 4 12 Analog ground 32 Bit 3 13 Test point 33 Bit 2 14 N/C 34 Bit 1 (MSB) 15 VDD 35 N/C 16 Reference output 36 Start convert 17 Status (EOC) 37 N/C or OE 18 Digital Ground 38 Digital ground 19 Test point 39 VDD 20 T/H control 40 Digital ground NOTES: 1. N/C are no connections between extern

46、al pins and internal circuitry. 2. Test points are connected to internal circuitry and should not be connected to externally. 3. 3-state output buffers included only in device types 02 and 04. Device types 01 and 03, pin 37 is a no connection. FIGURE 2. Terminal connections. Provided by IHSNot for R

47、esaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89595 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 12 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-PRF-38534 test requirements S

48、ubgroups (in accordance with MIL-PRF-38534, group A test table) Interim electrical parameters Final electrical parameters 1*, 2, 3, 4, 5, 6, 8, 9, 10, 11 Group A test requirements 1, 2, 3, 4, 5, 6, 8, 9, 10, 11 Group C end-point electrical parameters 1, 2, 3 End-point electrical parameters for Radiation Hardness Assurance (RHA) devices Not applicable * PDA applies to subgroup 1. 4. VERIFICATION 4.1 S