DLA MS35794 REV A-1972 BEARING SLEEVE STEEL-BACKED BIMETAL SPLIT TYPE ONE PIECE《拼合式单片钢背双金属材料轴承套》.pdf

《DLA MS35794 REV A-1972 BEARING SLEEVE STEEL-BACKED BIMETAL SPLIT TYPE ONE PIECE《拼合式单片钢背双金属材料轴承套》.pdf》由会员分享，可在线阅读，更多相关《DLA MS35794 REV A-1972 BEARING SLEEVE STEEL-BACKED BIMETAL SPLIT TYPE ONE PIECE《拼合式单片钢背双金属材料轴承套》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、6kf5-6 MS3579V REV A 33 m 9999932 0005795 T m C WALL (SEE NOTE 6) (SEE NOTE 7) I. MATERIAL. BEARINOS ARE TYPE STYLE I CLASS 2 OF MIL-B-13506.BACK* STEEL SHEET AND STRIP 2. FINISH: SHAFT OD. 16 MICROINCHES RHR OR LESS; BEARING IO 32 MICRMNCHES RHR OR LESS, BEARiNG OD LOW CAREM PER 00-s-698. LI NE: LE

2、ADE?) BROFIZE USING SAE MATERIAL DESIGWATION -2, m,oi 794. 63 MltRO(NCnES RHR OR LESS AS INTERPRETED IN AN.% E-46.1 SURFACE TEXTURE ( SURFACE ROUGHNESS, WCVINESS AND LAY 1. 3. WMANSHIP: ALL BEARINGS ARE INTENDED TO BE REAMED OR FiNISH BORED AFTER ASSEMBLY, FOR DESIGN 4. DIMENSIONS: ALL DIMENBIONS AR

3、E IN INCHES OR DEGREES. CLEPRANCE OVER NOMINAL FRACTIONAL SIZE SHAFTS. SHARP TOOLS SHALL BE USE0 TO MAINTAIN POROSITY. S. TOLERAMES: TCLERANCES ARE IN ACCORDANCE WITH ANSI yr4.5 (DIMENSIONING AND TOLERANCING FOR ENGINEERING ORAWiNGS).(TOLERANCES ARE TOTAL UNLESS SPECIFIED AS 2 ) 6. THE OUTSIDE D14ME

4、TER IS MEASURED WITH THE SPLIT CLOJEO. DIAMETER TOLERANCES UP TO 2.5 OD IS 0.0010,OVER 2.S”oO OQO!5. 1. LINING THICKNESS DIMEMSDiJ RANGES ARE: 0.017 TO 0.025 FOR 1/16 WALL AND0.024 TO 0.OW FOR 3/32 WALL. MINIMUM THICKkESS AFTER FINISHING IN PLXE: 0.013 FOR 1/16 WALL; 0.020 FOR 3/32 WKL. bM 0.100 TO

5、0.104 FOR 3/32 WALL. 8. ROUGH Wau DIMENSIONS AS FURNISHED BY THE MANLIFACTURER ARE: 0.068 TO 0.071 FOR 1/16 WALL Q CHAMFER FOR : 1/16 WALL: OUTSIDE 0.030 TO 0.050 AND INSIM 0.010 100.030 3/32 WALL: OUTSIDE 0.045 TO 0.071 ANO INSIDE0015 TO 0.045 IO. THE SUGCESTED MINIMUM PRESS FIT FOR BUSHINGS IS; 0.

6、003 FOR I OD, 0.004 FOR 2OD, AND 0.005 FOR 3.00. II. PART NUMBERS: THE PRT EXAMPLE : YS 35794-101 CONSISTS OF US AND THE MS NUMBER PLUS THE DASH WMBER. . 12. FOR DESltrN FEATURE PwIpoSES, THIS STANDARO TAKES PRECEOENCE OVER PROCUREMENT WMENTS 13. REFERENCE DOCOWENTS SHALL E F THE ISSUE IN EFFECT ON

7、DATE OF INVITATIONFOR BID. REFERENCED HEREIN. REDRAWNO .I I MILITARY STAW9iJ WEit BEARING.SLEEVE .STEEL-BiMD BIMETAL.SPLIT - )i NAVY- . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FED. M CLAU o -.NFJe nw NNNNNNN n t am 0-1 3 TITLE i Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-