DLA MS27781 REV D-2011 SWITCH TOGGLE ONE POLE ENVIRONMENTALLY SEALED LEVER LOCK INTEGRATED WIRE TERMINALS.pdf
《DLA MS27781 REV D-2011 SWITCH TOGGLE ONE POLE ENVIRONMENTALLY SEALED LEVER LOCK INTEGRATED WIRE TERMINALS.pdf》由会员分享,可在线阅读,更多相关《DLA MS27781 REV D-2011 SWITCH TOGGLE ONE POLE ENVIRONMENTALLY SEALED LEVER LOCK INTEGRATED WIRE TERMINALS.pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、AMSC N/A FSC 5930 INCH-POUND MS27781D 18 April 2011 SUPERSEDING MS27781C 28 September 1987 DETAIL SPECIFICATION SHEET SWITCH, TOGGLE, ONE POLE, ENVIRONMENTALLY SEALED, LEVER LOCK, INTEGRATED WIRE TERMINALS This specification is approved for use by all Departments and Agencies of the Department of De
2、fense. The complete requirements for acquiring the switch described herein shall consist of this specification and the latest issue of MIL-DTL-3950. FIGURE1. Dimensions and configuration Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27781D 2 NOTE
3、S: 1. Dimensions are inches. Metric equivalents are given for general information only. 2. Unless otherwise specified, tolerance is .020 (0.51 mm) for two place decimals and .005 (0.13 mm) for three place decimals. 3. For hardware detail specifications see appendix of MIL-DTL-3950. 4. Contact instal
4、ling/ removal tool in accordance with MIL-I-81969/14-03. 5. Grommet sealing plug, in accordance with MS27488A16. 6. Terminal shall adequately accept a wire contact within dimensional limits of SAE-AS39029/1-102. 7. Direction of internal mechanism movement is opposite to the direction of the toggle m
5、ovement. FIGURE1. Dimensions and configuration Continued REQUIREMENTS Maximum weight is .108 pound. The force required to release the locking mechanism shall be 3 to 5 pounds. Locking arrangement: Positive locking shall be accomplished and shall prevent motion of the toggle movement The locking mean
6、s at the top of the toggle bushing shall be capable of withstanding a torque of 20 inch-pounds applied in both directions immediately following the humidity test. The sealing grommet shall seal on a smooth wire insulation of .068 (1.73 mm) to .103 (2.62 mm) diameters. The terminal end of switch shal
7、l be color coded blue to indicate contact size. Sealing plugs may be used in nonfunctional grommet holes. Electrical rating: See table I. Inches mm Inches mm .005 0.13 .432 10.97 .008 0.20 .469 11.91 .012 0.30 .47 11.9 .020 0.51 .635 16.13 .060 1.52 1.05 26.7 .076 1.93 1.140 28.96 .38 9.7 1.270 32.2
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLAMS27781REVD2011SWITCHTOGGLEONEPOLEENVIRONMENTALLYSEALEDLEVERLOCKINTEGRATEDWIRETERMINALSPDF

链接地址:http://www.mydoc123.com/p-696877.html