DLA MS27382 REV C-2013 ADAPTER ASSEMBLY FLARELESS 45 ELBOW TUBE TO HOSE - WITH SWIVEL NUT.pdf
《DLA MS27382 REV C-2013 ADAPTER ASSEMBLY FLARELESS 45 ELBOW TUBE TO HOSE - WITH SWIVEL NUT.pdf》由会员分享,可在线阅读,更多相关《DLA MS27382 REV C-2013 ADAPTER ASSEMBLY FLARELESS 45 ELBOW TUBE TO HOSE - WITH SWIVEL NUT.pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、AMSC N/A FSC 4730 MS27382C 1 May 2013 SUPERSEDING MS27382B 25 September 2003 DETAIL SPECIFICATION SHEET ADAPTER ASSEMBLY, FLARELESS, 45 ELBOW, TUBE TO HOSE - WITH SWIVEL NUT This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requirements fo
2、r acquiring the product described herein shall consist of this specification sheet and MIL-DTL-27272. NOTES: 1. Dimension A, see table II, is measured between the hose end of the socket and the free end of the radius MS8000 series seal insert at its centerline when the socket is assembled on the nip
3、ple subassembly. 2. Socket may be hex or 2-flat sides. 3. If required lockwire holes to be drilled on this side of subassembly in accordance with SAE-AS1043. FIGURE 1. Adapter assembly illustration. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from
4、IHS-,-,-MS27382C 2 REQUIREMENTS Adapter assembly illustration, see figure 1. Intended use. This adapter is intended for use with hose in accordance with MIL-DTL-27267. Flareless fitting, hose connector design. Use MIL-DTL-25579/1 for application of NAS1760 design. Materials. Material and material co
5、des see table I. See applicable specification sheet and MIL-DTL-27272 for material of other components identified in table II for their material requirements. TABLE I. Materials and PIN codes. Material code Material Blank Combination of aluminum alloy and corrosion-resistant steel (CRES) C CRES TABL
6、E II. Adapter assembly composition. 1/ 2/ Size and material code Elbow subassembly size and material code Sleeve size and material code Socket size and material code A max inch (mm) MS27387 3/ MS27070 3/ MS27069 3/ -10C -10C -10C -10C 2.62 (66.5) -10 -10 -12C -12C -12C -12C 3.07 (78.0) -12 -12 -16C
7、-16C -16C -16C 3.21 (81.5) -16 -16 -20C -20C -20C -20C 3.72 (94.5) -20 -20 -24C -24C -24C -24C 4.12 (104.6) -24 -24 1/ Dimensions are in inches. 2/ Metric equivalents are given for general information only. 3/MS27069, MS27070 and MS27387 shall be dry film lubricated in accordance with table III, dry
8、 film is applied in accordance with MS27069, MS27070 or MS27387 as applicable. If required, lockwire holes to be drilled in accordance with SAE-AS1043 and suffix L added to the Part or Identifying Number (PIN). MS27069, MS27070 and MS27387 parts shall be lubricated with dry-film lubricant in accorda
9、nce with table III and shall be coated with the same type of dry film lubricant as indicated in the MS27382 PIN. No mixing of dry film lubricants shall be used on an assembly unless it is of the types specified by the “blank” designator. Provided by IHSNot for ResaleNo reproduction or networking per
10、mitted without license from IHS-,-,-MS27382C 3 NOTE: Avoid using graphite dry film lubes with aluminum unions and nipples because in a wet environment, graphite becomes corrosive to the aluminum. TABLE III. Dry film designator. Dry film designator SAE class or type designator Dry film characteristic
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLAMS27382REVC2013ADAPTERASSEMBLYFLARELESS45ELBOWTUBETOHOSEWITHSWIVELNUTPDF

链接地址:http://www.mydoc123.com/p-696750.html