1、AMSC N/A FSC 4730 MS27382C 1 May 2013 SUPERSEDING MS27382B 25 September 2003 DETAIL SPECIFICATION SHEET ADAPTER ASSEMBLY, FLARELESS, 45 ELBOW, TUBE TO HOSE - WITH SWIVEL NUT This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requirements fo
2、r acquiring the product described herein shall consist of this specification sheet and MIL-DTL-27272. NOTES: 1. Dimension A, see table II, is measured between the hose end of the socket and the free end of the radius MS8000 series seal insert at its centerline when the socket is assembled on the nip
3、ple subassembly. 2. Socket may be hex or 2-flat sides. 3. If required lockwire holes to be drilled on this side of subassembly in accordance with SAE-AS1043. FIGURE 1. Adapter assembly illustration. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from
4、IHS-,-,-MS27382C 2 REQUIREMENTS Adapter assembly illustration, see figure 1. Intended use. This adapter is intended for use with hose in accordance with MIL-DTL-27267. Flareless fitting, hose connector design. Use MIL-DTL-25579/1 for application of NAS1760 design. Materials. Material and material co
5、des see table I. See applicable specification sheet and MIL-DTL-27272 for material of other components identified in table II for their material requirements. TABLE I. Materials and PIN codes. Material code Material Blank Combination of aluminum alloy and corrosion-resistant steel (CRES) C CRES TABL
6、E II. Adapter assembly composition. 1/ 2/ Size and material code Elbow subassembly size and material code Sleeve size and material code Socket size and material code A max inch (mm) MS27387 3/ MS27070 3/ MS27069 3/ -10C -10C -10C -10C 2.62 (66.5) -10 -10 -12C -12C -12C -12C 3.07 (78.0) -12 -12 -16C
7、-16C -16C -16C 3.21 (81.5) -16 -16 -20C -20C -20C -20C 3.72 (94.5) -20 -20 -24C -24C -24C -24C 4.12 (104.6) -24 -24 1/ Dimensions are in inches. 2/ Metric equivalents are given for general information only. 3/MS27069, MS27070 and MS27387 shall be dry film lubricated in accordance with table III, dry
8、 film is applied in accordance with MS27069, MS27070 or MS27387 as applicable. If required, lockwire holes to be drilled in accordance with SAE-AS1043 and suffix L added to the Part or Identifying Number (PIN). MS27069, MS27070 and MS27387 parts shall be lubricated with dry-film lubricant in accorda
9、nce with table III and shall be coated with the same type of dry film lubricant as indicated in the MS27382 PIN. No mixing of dry film lubricants shall be used on an assembly unless it is of the types specified by the “blank” designator. Provided by IHSNot for ResaleNo reproduction or networking per
10、mitted without license from IHS-,-,-MS27382C 3 NOTE: Avoid using graphite dry film lubes with aluminum unions and nipples because in a wet environment, graphite becomes corrosive to the aluminum. TABLE III. Dry film designator. Dry film designator SAE class or type designator Dry film characteristic
11、s Blank Any SAE class or type below N/A SAE-AS1701 SAE-AS1701 class SAE-AS1701 temperature ranges F (C) 4 4 -65 to +1400F (-54 to 760C) 5 5 -65 to +850F (-54 to 454C) 6 6 -375 to +850F (-226 to 454C) SAE-AS5272 SAE-AS5272 type SAE-AS5272 temperature ranges. F (C) 7 Type I -90 to 400F (-68 to 204C) e
12、ndurance life of 250 min minimum 8 Type II -90 to 400F (-68 to 204C) endurance life of 450 min minimum 9 Type III Color 1 - Natural product color -90 to 400F (-68 to 204C) low Volatile organic compound with an endurance life of 450 min minimum 10 Type III Color 2 - Black color -90 to 400F (-68 to 20
13、4C) low Volatile organic compound with an endurance life of 450 min minimum Dry film designator MIL classification Dry film characteristics MIL-PRF-46010 1/ - MIL-PRF-46010 temperature ranges. F (C) 11 1 Color 1 natural product color, -90 to 400F (-68 to 204C) solvent resisting 12 2 Color 2 - Black
14、color -90 to 400F (-68 to 204C) solvent resisting 1/ Not for aerospace usage. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27382C 4 PIN: The PIN consists of prefix “MS”, the specification sheet number, dash number for 45 elbow adapter assembly s
15、ize, letter for material, blank or L for lockwire holes, and a blank or number for dry film lubricant. Unassigned PINs shall not be used. MS 27382 -10 C L PIN examples: MS27382-10C indicates a 45 elbow adapter assembly size 10, CRES with dry film class designator “blank”. MS27382-10C4 indicates a 45
16、 elbow adapter assembly size 10, CRES with dry film class designator 4. MS27382-10L indicates a 45 elbow adapter assembly size 10, a combination of aluminum and CRES, with lockwire holes, and with dry film class designator “blank”. Identification of product. PIN and the manufacturers trademark or CA
17、GE code shall be marked on a removable tag securely attached to the adapter. Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in thi
18、s document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. Referenced documents shall be of the issue in effect on date of invitations for bid. Changes from previous issues. Marginal notations are not used in this revision to identify changes with
19、respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-27272, this document references the following: MIL-DTL-25579/1 MIL-DTL-27267 MIL-PRF-46010 MS27069 MS27070 MS27387 MS8000 NAS1760 SAE-AS1043 SAE-AS1701 SAE-AS5272 SAE-AS33514 Specification sh
20、eet number MS prefix Material code letter (see table I) Size code number (see table II) Blank or “L” for lockwire holes Dry film lubricant designator (see table III) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27382C 5 CONCLUDING MATERIAL Custo
21、dians: Preparing activity: Army - AV DLA - CC Navy - AS Air Force - 99 (Project 4730-2013-029) DLA - CC Review activities: Army - AR, AT, MI Navy - MC, SA, SH Air Force - 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
