DLA MS27147 REV D-2003 ADAPTOR CONNECTOR-3-WAY NO 12 14 AND 16 AWG WATERPROOF《12 14 16 AWG防水3路连接器适配器》.pdf

《DLA MS27147 REV D-2003 ADAPTOR CONNECTOR-3-WAY NO 12 14 AND 16 AWG WATERPROOF《12 14 16 AWG防水3路连接器适配器》.pdf》由会员分享，可在线阅读，更多相关《DLA MS27147 REV D-2003 ADAPTOR CONNECTOR-3-WAY NO 12 14 AND 16 AWG WATERPROOF《12 14 16 AWG防水3路连接器适配器》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、MS27147D 17 June 2003 SUPERSEDING MS27147C 16 February 1988 DETAIL SPECIFICATION SHEET ADAPTER, CONNECTOR 3-WAY, NO. 12, 14 AND 16 AWG, WATERPROOF This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described

2、 herein shall consist of this specification. FIGURE 1. Configurations and dimensions. AMSC N/A 1 of 3 FSC 5935 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,

3、-MS27147D 2 Inches mm Inches mm Inches mm Inches mm .002 .003 .031 .040 .060 .065 .079 .051 .076 .787 1.02 1.52 1.65 2.00 .118 .137 .156 .157 .187 .218 .271 3.00 3.48 3.96 3.99 4.75 5.53 6.88 .344 .350 .394 .468 .470 .604 .700 8.74 8.89 10.00 11.89 11.94 15.34 17.78 .725 .855 1.062 1.304 1.750 18.42

4、 21.72 26.97 33.12 44.45 FIGURE 1. Configurations and dimensions Continued. REQUIREMENTS: Material: Shell: Rubber in accordance with ASTM D2000, M3BC610A14C12EO34F19. Terminal: Brass composition, temper half hard minimum in accordance with ASTM B36/B36M, ASTM B121/B121M or ASTM B124/B124M. Contact s

5、trip: Steel, commercial quality, 1008 to 1020, HRP&O or CR, temper optional, in accordance with QQ-S-698. Protective finish: Terminal: Silver plate, grade D, class S, .0002-inch minimum thickness in accordance with ASTM B700. Contact strip: Cadmium plate, type I, class A, in accordance with SAE AMS

6、QQ-P-416. Mating connector: See MS27143 and MS27144, style 1 and 2. When connectors are coupled, the following requirements shall apply: Voltage drop: The voltage drop shall not exceed 20 millivolts and shall meet the requirements outlined in MIL-STD-202, method 307. Dielectric strength: The assembl

7、y shall withstand dielectric strength test of 1000 volts, and meet the requirements of MIL-STD-202, method 302. Waterproof requirements: The assembly shall be waterproof. Refer to MIL-HDBK-1184, or equivalent, for guidance on waterproof testing. Salt spray corrosion test: The assembly shall meet the

8、 requirements of salt spray corrosion test outlined in MIL-STD-202, method 101 (5% saline solution, 200 hours duration). Marking shall consist of the MS number and the manufacturers identification in accordance with MIL-STD-130. Pull test: Terminals shall withstand a pull test of 100 pounds (46 kilo

9、grams). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27147D 3 Separation force: The force required to uncouple the connectors shall not exceed 50 percent of the values expressed in the pull test above when tested at -55C and at 85C. Part or Iden

10、tifying Number (PIN): MS27147-1. Reference drawing number 7982404 may be obtained from the U.S. Army Tank Automotive Command, Warren, MI 48397-5000. (Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes.) CONCLUDING MATERIAL Custodians: Preparing activity: Army AT DLA - CC Air Force - 11 Navy MC (Project 5935-4427-006) DLA CC Review activities: Army CR, CR4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-