DLA MS24265 REV R-2009 CONNECTORS RECEPTACLE ELECTRICAL SINGLE HOLE MOUNT MINIATURE CLASSES E F G H AND R [Use DLA MIL-DTL-83723 G SUPP 1 DLA MIL-DTL-83723 G DLA MIL-DTL-83723F (1).pdf

《DLA MS24265 REV R-2009 CONNECTORS RECEPTACLE ELECTRICAL SINGLE HOLE MOUNT MINIATURE CLASSES E F G H AND R [Use DLA MIL-DTL-83723 G SUPP 1 DLA MIL-DTL-83723 G DLA MIL-DTL-83723F (1).pdf》由会员分享，可在线阅读，更多相关《DLA MS24265 REV R-2009 CONNECTORS RECEPTACLE ELECTRICAL SINGLE HOLE MOUNT MINIATURE CLASSES E F G H AND R [Use DLA MIL-DTL-83723 G SUPP 1 DLA MIL-DTL-83723 G DLA MIL-DTL-83723F (1).pdf（23页珍藏版）》请在麦多课文档分享上搜索。

1、 DETAIL SPECIFICATION SHEET CONNECTORS, RECEPTACLE, ELECTRICAL, SINGLE HOLE MOUNT, MINIATURE, CLASSES E, F, G, H AND R This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of thi

2、s specification sheet and MIL-DTL-26500. FIGURE 1. Receptacle threaded for classes E, F, G, H and R. AMSC N/A FSC 5935 MS24265R 20 August 2009 SUPERSEDING MS24265P 6 February 2004 Inactive for new design after 14 November 1977. For new design, use MIL-DTL-83723, series III. INCH-POUNDProvided by IHS

3、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24265R 2Style S (socket insert) FIGURE 1. Receptacle threaded for classes F, G and R Continued Style S (socket insert) FIGURE 1. Receptacle threaded for classes F, G and R - Continued Provided by IHSNot for ResaleNo

4、 reproduction or networking permitted without license from IHS-,-,-MS24265R 3FIGURE 1. Receptacle threaded for classes F, G and R Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24265R 4Inches mm Inches mm .015 0.38 .155 3.94 .018 0.46 .

5、169 4.29 .019 0.48 .281 7.14 .020 0.51 .306 7.77 .022 0.56 .322 8.18 .024 0.61 .367 9.32 .031 0.79 .378 9.60 .045 1.14 .392 9.96 .054 1.37 .406 10.31 .062 1.57 .461 11.71 .078 1.98 .481 12.21 .100 2.54 .490 12.45 .109 2.77 .520 13.21 .133 3.38 .560 14.22 .140 3.56 .781 19.84 .142 3.60 .761 19.33 .15

6、3 3.89 .768 19.51 1.421 36.09 NOTES: 1. Dimensions are in inches. Unless otherwise specified, tolerances on decimals is .005. 2. Metric equivalents are given for general information only. 3. All diameters to be concentric with each other within .015 T.I.R. 4. All diameters in the same plane to be co

7、ncentric with each other within .004 T.I.R. 5. True position (T.P.) tolerances specified are for maximum material conditions (M.M.C). 6. Distance between end of shell and the point at which a gauge pin having the same basic diameter as the mating contact and a square face, engages socket contact spr

8、ing. 7. Dimensions on pin and socket contact locations and end of shells to insert faces apply when contacts are placed in inserts for inspection or application. 8. Dimensions .133 may reduce to .118 minimum under pressure caused by molded cable assemblies or sharp cable bends. Use tool MIL-I-81969/

9、17 to assemble contacts into this connector, and use tool MIL-I-81969/19 to remove contacts from this connector. 9. Thread relief groove is optional on shell. When groove is omitted, the length of full thread from front of shell will be .310 minimum and thread runout .385 maximum. 10. Thread relief

10、groove is optional on shell. When groove is omitted, the length of full thread from rear of shell will be .221 minimum. 11. Environment resistant (class F and R) receptacles, type T aluminum shell material. Grounding environment resistant (class G) receptacles, type T aluminum shell material. Enviro

11、nment resistant (class E) receptacles, type T, stainless steel shell material. These receptacles mate with plug MS24266 type T. FIGURE 1. Receptacle threaded for classes F, G and R Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24265R 5

12、FIGURE 2. Receptacle, threaded, stainless steel shell design for class E. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24265R 6NOTES: 1. Dimensions are in inches. Unless otherwise specified, tolerances on decimals is .005. 2. Metric equivalents

13、are given for information only. 3. All diameters to be concentric with each other within .015 T.I.R. 4. All diameters in the same plane to be concentric with each other within .004 T.I.R. 5. True position (T.P.) tolerances specified are for maximum material conditions (M.M.C.). 6. Distance between e

14、nd of shell and the point at which a gauge pin having the same basic diameter as the mating contact and a square face, engages socket contact spring. 7. Dimensions on pin and socket contact locations and end of shells to insert faces apply when contacts are placed in inserts for inspection or applic

15、ation. 8. Dimensions .133 may reduce to .118 minimum under pressure caused by molded cable assemblies or sharp cable bends. Use tool MIL-I-81969/17 to assemble contacts into this connector, and use tool MIL-I-81969/19 to remove contacts from this connector. 9. Thread relief groove is optional on she

16、ll. When groove is omitted, the length of full thread from front of shell will be .310 minimum and thread runout .385 maximum. 10. Thread relief groove is optional on shell. When groove is omitted, the length of full thread from rear of shell will be .221 minimum. 11. Environment resistant (class F

17、and R) receptacles, type T aluminum shell material. Grounding environment resistant (class G) receptacles, type T aluminum shell material. Environment resistant (class E) receptacles, type T, stainless steel shell material. These receptacles mate with plug MS24266 type T. FIGURE 2. Receptacle, threa

18、ded, stainless steel shell design for class E Continued. Inches mm .015 .38 .025 .64 .073 1.85 .085 2.16 .090 2.29 .120 3.05 .156 3.96 .220 5.59 .308 7.82 .378 9.60 .392 9.96 1.125 28.58 1.375 34.92 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS2

19、4265R 7FIGURE 3. Receptacle, threaded, shell design for class H, (hermetic) type T. Inches mm .015 .38 .025 .64 .073 1.85 .085 2.16 .090 2.29 .120 3.05 .156 3.96 .220 5.59 .308 7.82 .378 9.60 .392 9.96 1.125 28.58 1.375 34.92 Provided by IHSNot for ResaleNo reproduction or networking permitted witho

20、ut license from IHS-,-,-MS24265R 8NOTES: 1. Dimensions are in inches. Unless otherwise specified, tolerances on decimals is .005. 2. Metric equivalents are given for information only. 3. All diameters to be concentric with each other within .015 T.I.R. 4. All diameters in the same plane to be concen

21、tric with each other within .004 T.I.R. 5. True position (T.P.) tolerances specified are for maximum material conditions (M.M.C). 6. Distance between end of shell and the point at which a gauge pin having the same basic diameter as the mating contact and a square face, engages socket contact spring.

22、 7. Dimensions on pin and socket contact locations and end of shells to insert faces apply when contacts are placed in inserts for inspection or application. 8. Thread relief groove is optional on shell. When groove is omitted, the length of full thread from front of shell will be .310 minimum and t

23、hread runout .385 maximum. 9. Thread relief groove is optional on shell. When groove is omitted, the length of full thread from rear of shell will be .221 minimum. 10. Hermetic (class H) receptacle, type T. These receptacles mate with plug MS24266, type T stainless steel shell material. FIGURE 3. Re

24、ceptacle, threaded, shell design for class H, (hermetic) type T Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24265R 9Style P (pin insert) FIGURE 4. Receptacle, bayonet, socket insert. Provided by IHSNot for ResaleNo reproduction or ne

25、tworking permitted without license from IHS-,-,-MS24265R 10Style S (socket insert) FIGURE 4. Receptacle, bayonet, socket insert Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24265R 11NOTES: 1. Dimensions are in inches. Unless otherwise

26、 specified, tolerances on decimals is .005. 2. Metric equivalents are given for general information only. 3. All diameters to be concentric with each other within .015 T.I.R. 4. All diameters in the same plane to be concentric with each other within .004 T.I.R. 5. True position (T.P.) tolerances spe

27、cified are for maximum material conditions (M.M.C). 6. Distance between end of shell and the point at which a gauge pin having the same basic diameter as the mating contact and a square face, engages socket contact spring. 7. Dimensions on pin and socket contact locations and end of shells to insert

28、 faces apply when contacts are placed in inserts for inspection or application. 8. Dimensions .133 may reduce to .118 minimum under pressure caused by molded cable assemblies or sharp cable bends. Use tool MIL-I-81969/17 to assemble contacts into this connector, and use tool MIL-I-81969/19 to remove

29、 contacts from this connector. 9. Environment resistant (class F and R) receptacles, type B aluminum shell material. Grounding environment resistant (class G) receptacles, type B aluminum shell material. Environment resistant (class E) receptacles, type B stainless steel shell material. 10. Thread r

30、elief groove is optional on shell. When groove is omitted, the length of full thread from front of shell will be .310 minimum and thread runout .385 maximum. FIGURE 4. Receptacle, bayonet, socket insert Continued. Inches mm .004 .10 .005 .13 .010 .25 .025 .64 .062 1.57 .155 3.94 .169 4.29 .366 9.30

31、.376 9.55 .378 9.60 .392 9.96 .540 12.80 .560 14.22 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24265R 12FIGURE 5. Receptacle, bayonet, hermetic (class H). Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

32、m IHS-,-,-MS24265R 13STYLE P (PIN INSERT) HERMETIC (CLASS “H” RECEPTACLES, TYPE “B” THIS RECEPTACLE MATES WITH MS24266, TYPE “B” NOTES: 1. Dimensions are in inches. Unless otherwise specified, tolerances on decimals is .005. 2. Metric equivalents are given for information only. 3. All diameters to b

33、e concentric with each other within .015 T.I.R. 4. All diameters in the same plane to be concentric with each other within .004 T.I.R. 5. True position (T.P.) tolerances specified are for maximum material conditions (M.M.C). 6. Distance between end of shell and the point at which a gauge pin having

34、the same basic diameter as the mating contact and a square face, engages socket contact spring. 7. Dimensions on pin and socket contact locations and end of shells to insert faces apply when contacts are placed in inserts for inspection or application. FIGURE 5. Receptacle, bayonet, hermetic (class

35、H) - Continued. Inches mm .004 .10 .005 .13 .010 .25 .025 .64 .062 1.57 .155 3.94 .169 4.29 .366 9.30 .376 9.55 .378 9.60 .392 9.96 .540 12.80 .560 14.22 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24265R 14Shell size A UNEF-2A coupling B dia C

36、 dia + .005 (0.13) - .000 (0.00) E max Insert dia F UNEF-2A access 8 .562-24 (14.27) .508 (12.90) .428 (10.87) .318 (8.08) .437-28 (11.10) 10 .687-24 (17.45) .636 (16.15) .530 (13.46) .394 (10.01) .562-24 (14.27) 12 .875-20 (22.22) .806 (20.47) .700 (17.78) .564 (14.33) .750-20 (19.05) 14 .937-20 (2

37、3.80) .875 (22.22) .769 (19.53) .633 (16.08) .812-20 (20.62) 16 1.062-18 (26.97) 1.002 (25.45) .896 (22.76) .76 (19.30) .937-20 (23.80) 18 1.187-18 (30.15) 1.108 (28.14) 1.002 (25.45) .866 (22.00) 1.062-18 (26.97) 20 1.312-18 (33.32) 1.233 (31.32) 1.127 (28.62) .991 (25.17) 1.187-18 (30.15) 22 1.437

38、-18 (36.50) 1.358 (34.49) 1.252 (31.80) 1.116 (28.35) 1.312-18 (33.32) 24 1.562-18 (39.67) 1.483 (37.67) 1.377 (34.98) 1.241 (31.52) 1.437-18 (36.50) FIGURE 6. Receptacle dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24265R 15Shell si

39、ze F1-36NS-2A F1pitch dia FF max dia G max dia 8 .4340 (11.024) .4151/.4114 (10.544/10.450) .437 (11.10) .561 (14.25) 10 .5634 (14.310) .5454/.5415 (13.853/13.754) .562 (14.27) .696 (17.68) 12 .7334 (18.628) .7154/.7115 (18.171/18.072) .750 (19.05) .875 (22.22) 14 .8032 (20.401) .7841/.7806 (19.916/

40、19.827) .812 (20.62) .935 (23.75) 16 .9302 (23.627) .9110/.9074 (23.139/23.048) .938 (23.82) 1.062 (26.97) 18 1.0362 (26.319) 1.0171/1.0134 (25.834/25.740) 1.062 (26.97) 1.187 (30.15) 20 1.1611 (29.492) 1.1431/1.1385 (29.034/28.918) 1.182 (30.02) 1.312 (33.32) 22 1.2862 (32.669) 1.2670/1.2633 (32.18

41、2/32.088) 1.312 (33.32) 1.437 (36.50) 24 1.4111 (35.842) 1.3931/1.3885 (35.385/35.268) 1.432 (36.37) 1.562 (39.67) FIGURE 6. Receptacle dimensions Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24265R 16Shell size HH max grommet dia KK

42、dia + .000 (0.00) - .005 (0.13) MM N dia + .000 (0.00)- .004 (0.10)NN dia + .000 (0.00) - .003 (0.07) P dia + .000 (0.00)- .005 (0.13)8 .328 (8.33) .536 (14.30) .979 (24.97) .101 (2.56) .078 (1.98) .076 (1.93) 10 .420 (10.67) .659 (16.74) 1.104 (28.04) .094 (2.39) .093 (2.36) .089 (2.26) 12 .580 (14

43、.73) .829 (21.06) 1.291 (32.79) 14 .664 (16.86) .898 (22.81) 1.391 (35.33) 16 .769 (19.53) 1.025 (26.34) 1.516 (38.51) 18 .920 (23.37) 1.131 (28.73) 1.641 (41.68) 20 1.033 (26.24) 1.256 (31.90) 1.766 (44.86) 22 1.152 (29.26) 1.381 (35.08) 1.954 (49.63) 24 1.282 (32.56) 1.506 (38.25) 2.079 (52.81) Sh

44、ell size S U max hex UU + .000 (0.00) - .009 (0.22) V UNEF-2A 8 .605 (15.37) .828 (21.03) .310 (7.87) .625-20-UN-2A (15.88) 10 .730 (18.64) .953 (24.21) .374 (9.50) .750-20 (19.05) 12 .917 (23.29) 1.140 (28.46) .459 (11.66) .937-20 (23.80) 14 .980 (24.89) 1.250(31.75) .494 (12.55) 1.000-20 (25.40) 1

45、6 1.105 (28.07) 1.329 (33.76) .557 (14.15) 1.125-20-UN-2A (28.58) 18 1.225 (31.12) 1.455 (36.96) .610 (15.49) 1.250-20-UN-2A (31.75) 20 1.350 (34.29) 1.642 (41.71) .673 (17.09) 1.375-18- (34.92) 22 1.475 (37.46) 1.705 (43.31) .735 (18.67) 1.500-20-UN-2A (38.10) 24 1.600 (40.64) 1.892 (48.06) .798 (2

46、0.27) 1.625-18 (41.28) FIGURE 6. Receptacle dimensions Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24265R 17Shell size W .020 (.51) WW dia max Y .003 (.08) Z dia 8 .117 (2.97) 1.068 (27.13) .593 (15.06) .635 (16.13) 10 1.192 (30.28)

47、.718 (18.24) .760 (19.30) 12 1.380 (35.05) .905 (22.99) .947 (24.05) 14 1.505 (38.23) .968 (24.59) 1.010 (25.65) 16 1.630 (41.40) 1.093 (27.76) 1.135 (28.83) 18 1.740 (44.20) 1.217 (30.91) 1.260 (32.00) 20 1.860 (47.24) 1.342 (34.09) 1.385 (35.18) 22 .148 (3.76) 2.040 (51.82) 1.467 (37.26) 1.510 (38

48、.35) 24 2.160 (54.86) 1.592 (40.44) 1.635 (41.53) Position Shell size 8 Shell size 10 Shell sizes 12 thru 24 E F G E F G E F G Normal 60 180 300 60 180 300 50 170 290 6 46 166 286 46 166 286 50 170 290 7 46 166 286 46 166 286 50 170 290 8 60 180 300 60 180 300 50 170 290 9 89 209 329 89 209 329 50 170 290 Y 60 180 300 50 170 290 FIGURE 6. Receptacle dimension