DLA MS14314 REV D-2009 PLUGS PIPE BRASS OR BRONZE THREADED (SQUARE HEAD AND SQUARE SOCKET) CLASSES 250 AND 125.pdf

《DLA MS14314 REV D-2009 PLUGS PIPE BRASS OR BRONZE THREADED (SQUARE HEAD AND SQUARE SOCKET) CLASSES 250 AND 125.pdf》由会员分享，可在线阅读，更多相关《DLA MS14314 REV D-2009 PLUGS PIPE BRASS OR BRONZE THREADED (SQUARE HEAD AND SQUARE SOCKET) CLASSES 250 AND 125.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、C E C C A N N G 2 G 1 F A G 1 G 2 Y CORRED PATTERNS BOTH DESIGNS APPROVED SIZES .5“ -4“ INCLUSIVE CLASS 125 Z COUNTERSUNK (SQUARE SOCKET) PATTERN SIZES .5“ -4“ INCLUSIVE CLASS 125 E A X SOLID PATTERN SIZES .1250“ -4“ INCLUSIVE CLASS 250 DETAIL SPECIFICATION SHEET PLUGS, PIPE, BRASS OR BRONZE, THREAD

2、ED (SQUARE HEAD AND SQUARE SOCKET), CLASSES 250 AND 125 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and WW-P-460. FIGURE 1. Plug fittings. AM

3、SC N/A FSC 4730 INCH-POUND MS14314D 15 December 2009 SUPERSEDING MS14314C 28 February 1994 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14314D 2 Fitting type and size applicability. Dash Number Pipe Size mm Solid X Cored Y Countersunk Z - 1 - 2

4、- 3 - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11 - 12 1/8 (.125) 1/4 (.250) 3/8 (.357) 1/2 (.500) 3/4 (.750) 1 (1.000) 1-1/4 (1.250) 1-1/2 (1.500) 2 (2.000) 2-1/2 (2.500) 3 (3.000) 4 (4.000) 3.18 6.35 9.53 12.70 19.05 25.40 31.75 38.10 50.80 63.50 76.20 101.60 X X X X X X X X X X X X . . . X X X X X X X X X .

5、. . X X X X X X X X X NOTES: 1. Metric equivalents are given for information only. 2. Material: Brass or bronze in accordance with ASME-B16.15. 3. Protective Coating: None 4. Dimensions: In accordance with ASME-B16.15, table titled “Dimensions of Square Head and Square Socket Plugs Class 250”. 5. Th

6、read: As specified in ASME-B16.15. 6. Marking: In accordance with ASME-B16.15. 7. Part or Identifying Number (PIN): The MS PIN consists of the MS number, the dash number, and the fitting Identification letter(s). When left-hand threads are required, add the letter “L” to the PIN. FIGURE 1. Plug fitt

7、ings Continued. PIN: MS 14314 -3 X L Examples: MS14314 4X represents a 1/2 NPS solid pattern square head plug. MS14314 10ZL represents a 1-1/2 NPS countersunk plug, left-hand threads. MS prefix Basic specification number Dash number on figure 1 Outside head, inside head, face designator, see figure

8、1 Thread designator: Blank right hand thread, L- left hand thread Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14314D 3 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previou

9、s issue, due to the extent of the changes. Referenced documents. In addition to WW-P-460, this document references the following: ASME-B16.15 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - MC Air Force - 99 DLA - CC (Project 4730-2009-011) Review activities: Army - AR,

10、 CE, EA Navy SA, SH, YD Air Force - 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-