DLA MIL-PRF-1 422J-2004 ELECTRON TUBE CATHODE RAY TYPES 7YP1 7YP2 AND 7YP7.pdf

《DLA MIL-PRF-1 422J-2004 ELECTRON TUBE CATHODE RAY TYPES 7YP1 7YP2 AND 7YP7.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-1 422J-2004 ELECTRON TUBE CATHODE RAY TYPES 7YP1 7YP2 AND 7YP7.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、 MIL-PRF-1/422J 2 July 2004 SUPERSEDIING MIL-PRF-1/422H 12 October 1998 PERFORMANCE SPECIFICATION SHEET ELECTRON TUBE, CATHODE RAY TYPES 7YP1, 7YP2, AND 7YP7 This specification is approved for use by all Depart- ments and Agencies of the Department of Defense. The requirements for acquiring the elec

2、tron tube described herein shall consist of this document and the latest issue of MIL-PRF-1. DESCRIPTION: Electrostatic deflection and focus, square face, five beam. DIMENSIONS AND PIN CONNECTIONS: See figure 1. ABSOLUTE RATINGS: Parameter: Ef Ec1 Eb1 Eb2 Eb3 ed Rg Zd Ehk Eb3/Eb2 Unit: V V dc V dc V

3、 dc V dc v Meg Meg V dc Ratio Maximum: 6.9 -200 1,650 3,850 7,700 1,250 1.5 1.0 see note 1 180 2.0 see note 2 Minimum: 5.7 0 - - - - - - - - - - - - - - - - - - - - - - - - Test conditions: see note 3 6.3 Adjust focus 2,000 4,000 - - - - - - 1.0 - - - 2.0 _ GENERAL: Qualification - Required. Prior t

4、o shipment, 7YP2 tubes shall be electrically burned-in on a 100 percent basis. These tubes shall be operated at standard operating conditions with 5 microamperes direct current applied to each gun for a period of 48 hours. During this 48 hour period, the tube shall be turned off for 30 minutes (allo

5、wed to cool) and then turned on to continue burn-in at least 4 times. Following burn-in, each tube shall be tested in accordance with the following MIL-STD-1311 tests: Method Test Method Test 5201 Voltage breakdown 5241 Grid-cutoff voltage 5206 Gas “cross” 5251 Grid No. 1 leakage current 5223 Modula

6、tion 5251 Anode No. 2 leakage current 5231 Spot displacement (leakage) 5201 Electrode current (Anode No. 1) Those tubes which fail any of these tests shall not be shipped. Visual inspections shall be made to ensure that all JAN 7YP2 CRTs are failure free from arcing for continuous and intermittent o

7、perational testing during all manufacturing and acceptance testing. Pressure test method 1141 shall be performed, except 30 pounds per square inch (PSI) absolute pressure shall be applied in lieu of 45 PSI absolute, on a 100 percent basis prior to shipment for the JAN 7YP2 tube only. Only those tube

8、s meeting the acceptance criteria for this test shall be shipped. When a P2 CRT screen is specified, the phosphors shall be in compliance with Electronic Industries Alliance TEPAC Publication, TEP 116-B, Optical Characteristics of Cathode Ray Tubes. AMSC N/A FSC 5960 INCH-POUND Provided by IHSNot fo

9、r ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-1/422J 2TABLE I. Testing and inspection. Inspection Method MIL-STD-1311 Notes Conditions Symbol Limits Min Limits Max Unit Conformance inspection, part 1 Voltage breakdown Voltage breakdown (electrostatic types) Gas

10、 “cross” Bulb, screen and faceplate quality Light output Modulation Spot position (electrostatic deflection) Spot displacement (leakage) Grid cutoff voltage Grid No. 1 leakage current Anode No. 2 leakage current 5201 5201 5206 5106 5221 5223 5231 5231 5241 5251 5251 - - - - - - 6, 11 - - - 11 11 - -

11、 - 8 - - - - - - - - - - - - Ib3 = 50 A dc P1 screen; Ib3 = 50 A P2 screen; Ib3 = 50 A, for 7YP2 only Ib3 = 50 A dc - - - - - - - - - - - - Light Light Ec1 - - - - - - Ec0 Ic1 Ib2 - - - - - - - - - - - - 25 25 - - - - - - - - - -90 - - - - - - - - - - - - - - - - - - - - - - - - 55 16 10 -50 3 10 -

12、- - - - - - - - - - - ftL ftL V dc mm mm V dc A dc A dc Conformance inspection, part 2 Screens Type P2 Type P7 Type P7 Heater current Electrode current (anode No. 1) Electrode current (cathode) Base alignment (electrostatic types) Trace and bulb alignment (rectangular electrostatic types) Side termi

13、nal alignment (electrostatic types) 5221 1301 5201 5201 5101 5101 5101 11, 13 11, 13 11, 13 - - - - - - - - - - - - - - - - - - Ib3 = 50 A dc 3D4; base key 1D2 trace and bulb wall with contact button 3D4 D1(1) D1(5) G5:1 Ib Ib1 Ik - - - - - - - - - 360 400 4 540 -15 - - - - - - - - - - - - - - - - -

14、 - - - - 660 +10 1,000 - - - 3 - - - cB cB cB mA A dc A dc - - - Degrees - - - See notes at end of table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-1/422J 3TABLE I. Testing and inspection -Continued. Inspection Method MIL-STD-1311 Not

15、es Conditions Symbol Limits Min Limits Max Unit Conformance inspection, part 2 - Continued Side terminal and base alignment Neck and base alignment (electrostatic types) Line width “A” (electrostatic deflection) Line width “B” (electrostatic deflection) Focusing voltage at Ib = 25 A direct current D

16、eflection factor Deflection factor Heater-cathode leakage current Angle between traces Trace alignment Base pin solder depth Secureness of base, cap or insert Permanence of marking 5101 5101 5226 5226 5246 5248 5248 5251 5101 - - - 1111 1101 1105 - - - - - - 7 - - - 9 10 - - - - - - 12 - - - 15 - -

17、- Base key, collar index pin Ib3 = 25 A dc Ib3 = 25 A dc 1D2 3D4 Sample size shall be 1 percent of lot (lot = 1 months production) For qualifications only. - - - - - - Width Width Eb1 DF DF Ihk - - - - - - - - - - - - - - - - - - - - - - - - - - - 450 68 27 - - - 88 - - - - - - - - - - - - - - - - -

18、 - 0.65 0.80 650 80 37 15 92 - - - 0 failures - - - - - - - - - - - - mm mm V dc V dc/in. V dc/in. A dc Degrees - - - - - - - - - - - - Conformance inspection, part 3 Life test Life-test end points: Modulation Line width “A” Line width “B” Pressure (implosion) Vibration - - - - - - 5223 5226 5226 11

19、41 5111 14 - - - - - - - - - 5 5 Group C; t = 500 hours; Ib3 = 25 A dc Ib3 = 40 A dc Ib3 = 18 A dc Ib3 = 18 A dc For qualification only. - - - Ec1 Width Width - - - Width - - - - - - - - - - - - - - - - - - - - - 55 0.65 0.80 - - - 1.0 - - - V dc mm mm - - - mm See notes at end of table I. Provided

20、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-1/422J 4TABEL I. Testing and inspection -Continued. Inspection Method MIL-STD-1311 Notes Conditions Symbol Limits Min Limits Max Unit Conformance inspection, part 3 - Continued Direct-interelectrode capa

21、citance Neck and bulb alignment (electrostatic types) Stray light emission (conventional types) Cathode illumination Deflection-factor uniformity Interaction factor Shock Base material insulating quality 1331 5101 5216 5216 5248 5250 5115 1216 4, 5 5 5 5 5 5 5 5 k to all g1 to all D1 to D2 D3 to D4

22、D1 to all D2 to all D3 to all D4 to all Eb2 = 3,850 V dc; Eb3 = 7,700 V dc For qualification only 1D2 3D4 For qualification only For qualification only Ck Cg1 C1D2 C3D4 CD1 CD2 CD3 CD4 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

23、 - - - - - - - - - - - - - - 6.5 7.0 2.7 3.2 8.1 8.0 7.8 7.8 - - - - - - - - - 2 5 10x10-6- - - - - - pF pF pF pF pF pF pF pF - - - - - - - - - % % in./V dc - - - - - - NOTES: 1. The deflection electrode circuit resistance should be 1 M or less and approximately equal, otherwise beam shift at high d

24、rives can be expected. Higher resistance values up to 5 M may be used for low-beam current operation. 2. This tube is designed for optimum performance when operating at an Eb3/Eb2 ratio of 2.0. Operation at other ratios of Eb3/Eb2 may result in changes in deflection uniformity and pattern distortion

25、. 3. All tests except direct-interelectrode capacitance, vibration and interaction factor, shall be made on each unit separately. Each deflection plate shall be connected to A2 through a resistance of 1 M 10%. 4. All other electrodes contained within the envelope are to be tied together. 5. This tes

26、t shall be performed during the initial production and once each succeeding 12-calender months in which there is production. A sampling plan shall be used, with sample of three tubes with an acceptance number of zero,. In the event of failure, the test will be made as a part of conformance inspectio

27、n, part 2, with an Acceptance Level of 6.5 (see note 16). The regular “12 calendar month” sampling plan shall be reinstated after three consecutive samples have been accepted. 6. The pattern size shall be adjusted to 1.5 inches (38 mm) in the limited scan direction. 7. Due to limited scan of 3D4 pla

28、tes, the length of scan in the 3D4 direction shall be limited to 1 inch from the undeflected spot position. Line width “B” shall be measured at 0.75 inch ( 19.1 mm) from the undeflected spot position. 8. From the spot positions as indicated on figure 1. Provided by IHSNot for ResaleNo reproduction o

29、r networking permitted without license from IHS-,-,-MIL-PRF-1/422J 5TABLE I. Testing and inspection - Continued. 9. The deflection in this direction covers the minimum useful screen width following the bulb contour. 10. The deflection in this direction is limited to 0.75 inch ( 19.1 mm) minimum from

30、 the undeflected spot position. 11. This test to be performed at the conclusion of the holding period. This test applies only when P1 CRT screen phosphors are specified. 12. Corresponding traces of each unit are to be within 2 degrees of each other. 13. This test is not required unless specified in

31、the purchase order or contract. 14. The tube manufacturer (7YP2 only) shall provide the user with two years of service life warranty commencing with shipment from the tube manufacturer. The second year of this warranty shall be pro-rated. Other terms and agreements regarding this warranty (i.e., pro

32、-rating, handling of defectives) shall be negotiated at the time of purchase. The appropriate applicable documentation shall be provided by the tube manufacturer and this documentation shall accompany the tube. The user will be responsible for completing and returning the documentation to the manufa

33、cturer. 15. This test shall be performed on 100 percent basis and torque shall be 20 inch-pounds (7YP2 only). Immersion test for qualification only. 16. This specification sheet uses accept on zero defect sampling in accordance with MIL-PRF-1, table III. Provided by IHSNot for ResaleNo reproduction

34、or networking permitted without license from IHS-,-,-MIL-PRF-1/422J 6NOTES: 1. These dimensions are for information and are not required for inspection purposes. 2. For pin alignment use JEDEC gage GB25-1. 3. Bulb contact J1-22, pin number 1 of base A22-101, and guide lug of base B25-139 shall each

35、align with 3D4 trace within 10. 4. Beam A shall center on position A as shown within 0.312 R. This requirement shall also apply to beams B, C, D, and E and their corresponding positions. 5. Useful screen radius. 6. Lancaster Glass bulb outline A-4314 or equivalent. FIGURE 1. Outline drawing of elect

36、ron tube types 7YP1, 7YP2 and 7YP7. Dimensions in inches with metric equivalents (mm) in parentheses Ltr Minimum Maximum Conformance inspection, part 2 A 18.125 (460.38) 18.875 (479.42) B 5.438 (138.13) 5.531 (140.49) C 3.688 (93.68) 3.813 (96.85) D 2.250 (57.15) E 4.344 (110.34) 4.468 (113.49) H 2.

37、797 (71.04) J 5.125 (130.18) 5.375 (136.52) K 12.125 (307.98) 12.375 (314.32) Conformance inspection, part 3 (See note 5) N P S Bulb contact: J1-22 Base, collar: A22-101 Base, B25-139 (See note 2) Reference dimensions (See note 1) F 40.00 (1016.0) G 0.75 (19.0) L 0.75 (19.0) M 1.50 (38.1) R 10.00 (2

38、54.0) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-1/422J 722 Pin collar base 25 Pin base Pin no. Element Beam Pin no. Element Beam 1 Accelerator 1 Focusing electrode A 2 Deflector D2 A 2 Heater A 3 Deflector D1 A 3 Heater A 4 Deflector D3

39、 A 4 Focusing electrode B 5 Deflector D4 A 5 Heater B 6 Deflector D1 B 6 Heater B 7 Deflector D3 B 7 Focusing electrode C 8 Deflector D4 B 8 Heater C 9 Deflector D2 B 9 Heater C 10 Deflector D3 C 10 Focusing electrode D 11 Deflector D1 C 11 Heater D 12 Deflector D2 C 12 Heater D 13 Accelerator 13 Fo

40、cusing electrode E 14 Deflector D4 C 14 Heater E 15 Deflector D1 D 15 Heater E 16 Deflector D2 D 16 Grid number 1 A 17 Deflector D4 D 17 Cathode A 18 Deflector D3 D 18 Grid number 1 B 19 Deflector D4 E 19 Cathode B 20 Deflector D3 E 20 Grid number 1 C 21 Deflector D2 E 21 Cathode C 22 Deflector D1 E

41、 22 Grid number 1 D 23 Cathode D 24 Grid number 1 E 25 Cathode E FIGURE 1. Outline drawing of electron tube types 7YP1, 7YP2 and 7YP7 - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-1/422J 8NOTES Referenced documents. In addition

42、 to MIL-PRF-1, this specification sheet sheet references MIL-STD-1311. Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liabilit

43、y whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the previous issue. Custodians: Preparing activity: Army - CR DLA - CC Navy

44、 - EC Air Force - 11 (Project 5960-3711) DLA - CC Review activities: Army - AV, CR4 Navy - AS, CG, MC, OS Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at www.dodssp.daps.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-