DLA DSCC-DWG-86117 REV E-2003 CONNECTOR RECEPTACLE ELECTRICAL SERIES SSMA SOCKET CONTACT FOR SEMIRIGID CABLE《针触式SSMA系列的半刚性电缆的电器插头连接器》.pdf

《DLA DSCC-DWG-86117 REV E-2003 CONNECTOR RECEPTACLE ELECTRICAL SERIES SSMA SOCKET CONTACT FOR SEMIRIGID CABLE《针触式SSMA系列的半刚性电缆的电器插头连接器》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-86117 REV E-2003 CONNECTOR RECEPTACLE ELECTRICAL SERIES SSMA SOCKET CONTACT FOR SEMIRIGID CABLE《针触式SSMA系列的半刚性电缆的电器插头连接器》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 NOTICE OF REVISION (NOR) This revision described below has been authorized for the document listed. 1. DATE (YYMMDD) 03-01-17 Form Approved OMB No. 0704-0188 Public reporting burden for this collection is estimated to average 2 hours per response, including the time for reviewing instructions, sear

2、ching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Department of Def

3、ense, Washington Headquarters Services, Directorate for Information Operations and Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302, and to the Office of Management and Budget, Paperwork Reduction Project (0704-0188), Washington, DC 20503. PLEASE DO NOT RETURN YOUR COMPLET

4、ED FORM TO EITHER OF THESE ADDRESSED. RETURN COMPLETED FORM TO THE GOVERNMENT ISSUING CONTRACTING OFFICER FOR THE CONTRACT/ PROCURING ACTIVITY NUMBER LISTED IN ITEM 2 OF THIS FORM.2. PROCURING ACTIVITY NO. 3. DODAAC 4. ORIGINATOR b. ADDRESS (Street, City, State, Zip Code)Defense Supply Center Columb

5、us 3990 East Broad Street Columbus, Ohio 43216-5000 5. CAGE CODE037Z3 6. NOR NO.5935-R012-03 a. TYPED NAME (First, Middle Initial, Last) Ron Gary 7. CAGE CODE037Z3 8. DOCUMENT NO.86117 9. TITLE OF DOCUMENT Connector, Receptacle, Electrical, Series SSMA, Socket Contact, For Semirigid Cable 10. REVISI

6、ON LETTER 11. ECP NO.N/A a. CURRENTD b. NEWE 12. CONFIGURATION ITEM (OR SYSTEM) TO WHICH ECP APPLIESALL 13. DESCRIPTION OF REVISIONSheet 1: Revisions Ltr. Column; add “E” Revisions description column; add “Changes in accordance with NOR 5935-R012-03”. Revisions date column; add “” Revisions rev stat

7、us of pages, blocks 1 and 5, add “E”. Revisions rev status of sheet 1, add “E”. Sheet 5: Revisions Ltr block, delete “D” and substitute “E” Sheet 5: Add the following new Vendor PIN “ DSCC drawing PIN 1/ Vendor CAGE Vendor reference PIN Number 86117ZSG 00779 1045398-1 “ 14. THIS SECTION FOR GOVERNME

8、NT USE ONLY a. (X one) X (1) Existing document supplemented by the NOR may be used in manufacture. (2) Revised document must be received before manufacturer may incorporate this change. (3) Custodian of master document shall make above revision and furnish revised document. b. ACTIVITY AUTHORIZED TO

9、 APPROVE CHANGE FOR GOVERNMENTDSCC-VAI c. TYPED NAME (First, Middle Initial, Last)ROBERT HEBER d. TITLECHIEF, INTERCONNECTION DEVICES e. SIGNATURERobert M. Heber f. DATE SIGNED (YYMMDD) 03-01-17 15a. ACTIVITY ACCOMPLISHING REVISIONDSCC-VAI b. REVISION COMPLETED (Signature)Ron Gary c. DATE SIGNED (YY

10、MMDD)03-01-17 DD Form 1695, APR 92 Previous editions are obsolete Sheet 5: Add the following vendor: “ Vendor CAGE Vendor name Number and address 00779 TYCO Electronics P. O. Box 3608 Harrisburg PA 17105 “ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-

11、,-,-REVISIONS LTR DESCRIPTION DATE APPROVED A Modify length dimension. Clarification requirements. 27 Aug 1987 R. Marbais B Add CAGE 34078 as source. 4 Jun 1991 Randy Larson C PIN and source update. 16 Nov 2001 Robert M. Heber D Mounting hole dimension change on figure 1. 22 May 2002 Robert M. Heber

12、 Requirements of DSCC drawing 84148 are applicable. Prepared in accordance with ASME Y14.100 REV PAGE REV D D D C C REV STATUS OF PAGES PAGE 1 2 3 4 5 PREPARED BY PMIC N/A Ron Gary DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43216-5000 CHECKED BY Jeffery Bohannon APPROVED BY Richard Marbais TITLE

13、 CONNECTOR, RECEPTACLE, ELECTRICAL, SERIES SSMA, SOCKET CONTACT, FOR SEMIRIGID CABLE SIZE CAGE CODE 037Z3 DWG. NO. 86117 Original date of drawing 27 January 1987 A REV D PAGE 1 OF 5 AMSC N/A 5935-E690 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSNot

14、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 86117 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV D PAGE 2 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Wrench flats

15、are to accommodate standard wrench opening in accordance with FED-STD-H28, appendix 10. 4. All undimensioned pictorial configurations are for reference purposes only. 5. Dimension .690 (17.40 mm) defines the maximum overall length of the connector when assembled to the cable. 6. Method of assembly t

16、o the cable shall be solder. 7. Unless otherwise specified, tolerances are .005 (0.13 mm). FIGURE 1. General configuration. Inches mm .0875 2.22 .120 3.04 .125 3.17 .172 4.36 .188 4.77 .190 4.82 .250 6.35 .375 9.52 .450 11.43 .555 14.09 .690 17.52 Provided by IHSNot for ResaleNo reproduction or netw

17、orking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 86117 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV D PAGE 3 ENGINEERING DATA: Nominal impedance: 50 ohms. Frequency range: 0 - 26 GHz. (Connector performance only, frequency range is dependent on cable used.)

18、 Voltage rating: 250 V rms at sea level. 60 V rms at 70,000 feet. Temperature rating: -65C to +165C. REQUIREMENTS: Requirements of drawing 84148 applicable. Dimensions and configuration: See figure 1. Force to engage and disengage: Longitudinal force: Not applicable. Torque: 2.0 inch-pounds, maximum

19、. Mating characteristics: Center contact (socket): Oversize test pin: .0213 +.0001, -.0000 inches. Test pin finish: 16 microinches. Insertion depth: .045. Number of insertions: 1. Insertion force test: Steel test pin dia: .0208 +.0001, -.0000 inches. Insertion depth: .050 to .065 Test pin finish: 16

20、 microinches. Insertion force: 3 pounds maximum. Withdrawal force test: Steel test pin dia: .0195 +.0000, -.0001 inches. Insertion depth: .050 to .065. Withdrawal force: 1 ounce, minimum. Test pin finish: 16 microinches. Coupling proof torque: Not applicable. Hermetic seal: Not applicable. Leakage (

21、pressurized connectors): Not applicable. Center contact retention: Not applicable. Radial torque: Not applicable. Voltage standing wave ratio (VSWR): 1.07 + .010 (FGHz), maximum. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO.

22、037Z3 86117 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV C PAGE 4 Moisture resistance: Method 106, MIL-STD-202, no measurements at high humidity. Insulation resistance shall be at least 200 megohms within 5 minutes after removal from humidity. Contact resistance (in milliohms, maxim

23、um): Initial After environment Center contact: 4.0 4.0 Outer contact: 2.0 Not applicable Outer conductor to body: 0.5 Not applicable Dielectric withstanding voltage at sea level: 750 V rms, minimum. Vibration, high frequency: Method 204, test condition D, MIL-STD-202. Corona level: Altitude: 70,000

24、feet. 190 V rms, minimum. Shock (specified pulse): Method 213, test condition I, MIL-STD-202. Thermal shock: Method 107, test condition B, MIL-STD-202, except test high temperature shall be +85C. Barometric pressure (reduced): Not applicable. RF high potential withstanding voltage: 500 V rms, minimu

25、m. Frequency: 5 MHz. Leakage current: Not applicable. Cable retention force: 30 pounds, minimum. Torque: 16 ounce-inches, minimum. Coupling mechanism retention force: Not applicable. RF leakage: -90 F (F in GHz) dB, minimum. Test at a frequency between 2 and 3 GHz. RF insertion loss: .04 F, GHz dB,

26、maximum. Note: These parts are for use in general radio frequency applications. Part or Identifying Number (PIN): See table I. TABLE I. Connector to cable reference. PIN Cable accommodation 86117ZSG M17/133-RG405 M17/133-0001 through -00005 Provided by IHSNot for ResaleNo reproduction or networking

27、permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 86117 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV C PAGE 5 Approved sources of supply are listed herein. Additional sources will be added as they become available. The vendors listed on the requirements drawing hav

28、e agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI. DSCC drawing PIN 1/ Vendor CAGE number Vendor reference PIN 34078 SSM-0085-83-001-00 86117ZSG 95077 2746-6001 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Vendor CAGE Vendor name number and address 34078 Midwest Microwave 6564 South State Road Saline, MI 48176 95077 Solitron/Vector Microwave Products 3301 Electronics Way West Palm Beach, FL 33407 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-