DLA DSCC-DWG-13015-2013 ATTENUATORS FIXED COAXIAL LINE (SERIES N) FREQUENCY RANGE DC TO 12 4 GHz CLASS III LOW POWER.pdf

《DLA DSCC-DWG-13015-2013 ATTENUATORS FIXED COAXIAL LINE (SERIES N) FREQUENCY RANGE DC TO 12 4 GHz CLASS III LOW POWER.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-13015-2013 ATTENUATORS FIXED COAXIAL LINE (SERIES N) FREQUENCY RANGE DC TO 12 4 GHz CLASS III LOW POWER.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.100 REV STATUS REV OF PAGES PAGES 1 2 3 4 5 6 PMIC N/A PREPARED BY Michael A. Radecki DESIGN ACTIVITY DLA LAND AND MARITIME COLUMBUS, OH 43218-3990 Original date of drawing 2 April 2013 CHECKED BY Andrew R. Ernst TITLE ATT

2、ENUATORS, FIXED, COAXIAL LINE (SERIES N), FREQUENCY RANGE: DC TO 12.4 GHz, CLASS III, LOW POWER APPROVED BY Robert M. Heber SIZE A CODE IDENT. NO. 037Z3 DWG NO. 13015 SCALE N/A REV PAGE 1 OF 6 AMSC N/A 5985-2013-E03Provided by IHSNot for ResaleNo reproduction or networking permitted without license

3、from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13015 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for fixed coaxial line (series N) attenuators screened to MIL-DTL-3933. The attenuators described herein are direct replacements for non-

4、screened (N) MIL-DTL-3933/18 attenuators that lost their qualified MIL-DTL-3933 source (see 6.4 and table II). 1.2 Part or Identifying Number (PIN). The complete PIN will be in the following form: 13015 -05 Drawing Dash number number (see table I) 2. APPLICABLE DOCUMENTS 2.1 General. The documents l

5、isted in this section are specified in sections 3, 4, and 5 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list,

6、 document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, and 5 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbo

7、oks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-DTL-3933 - Attenuators, Fixed, Space Level, Non-Space Level, General Specification for.

8、 (Copies of these documents are available online at https:/assist.dla.mil/quicksearch or from the DLA Document Service Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict betw

9、een the text of this document and the references cited herein (except for related specification sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interf

10、ace and physical dimensions. The interface and physical dimensions shall be as specified in MIL-DTL-3933 and herein (see figure 1). 3.1.1 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of capacitor components and solder shall

11、 not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.2 Rated temperature. -55C to +125C. 3.3 Maximum weight. 5 ounces. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUM

12、BUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13015 REV PAGE 3 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Metric equivalents are in parentheses. 4. Dimension L is listed in table I. FIGURE 1. Dimensions and configuration. 3.4 Electrical chara

13、cteristics. 3.4.1 Nominal impedance. 50 ohms. 3.4.2 Attenuation: See table I. Stability and sensitivity: Frequency sensitivity, maximum: 0.1 dB/dB/GHz. Temperature sensitivity of attenuation, maximum: 0.0004 dB/dB/C. 3.4.3 Power. See table I. Power sensitivity for full input power, maximum: 0.005 dB

14、/dB/Watt. 3.4.4 VSWR. See table I. 3.4.5 Connector repeatability. Maximum variation in attenuation: 0.02 dB. 3.5 Engineering data. 3.5.1. Operating frequency range. DC to 12.4 GHz. 3.5.2 Test frequency range. 3.5.2.1 For VSWR and attenuation measurements, measured or recorded, when using an Automati

15、c Network Analyzer (ANA) or equivalent test equipment: 100 MHz (or lower) to 12.4 GHz. Maximum attenuation change after: Up to 10 dB, inclusive (dB) Over 10 dB (dB/dB) Temperature change/ thermal shock 0.05 0.005 Vibration or shock 0.1 0.01 Moisture resistance or salt spray 0.2 0.02 Peak power 0.05

16、0.005 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13015 REV PAGE 4 3.5.2.2 Basic test frequency for sensitive measurements like connector repeatability, temperature sensitiv

17、ity, power sensitivity and any other measurements where a delta specification is imposed: 6.0 GHz TABLE I. Electrical characteristics. Dash number Attenuation (dB) Maximum power Input VSWR maximum 1/ Dimension L (inches) Maximum Nominal Deviation DC to 4.0 GHz 4.0 to 8.0 GHz 8.0 to 12.4 GHz DC to 12

18、.4 GHz AV (W) at 25C (continuously) Peak (kW) 05 30 0.8 2 2/ 1 3/ 1.15:1 1.20:1 1.25:1 2.70 (68.58) 1/ VSWR value is for both ends. 2/ Power input is derated linearly to 0 watts at +125. 3/ Peak power for a duty cycle of 5 x 10-4 ;maximum pulse duration 5 microseconds. 3.6 Marking. In accordance wit

19、h MIL-DTL-3933, except the attenuator shall be marked with the PIN as specified herein (see 1.2). 13015-05 - Drawing PIN 12345 - Manufacturers source code or logo 1305 - Date code XXXX - Serialization 3.7 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufac

20、turer shall be listed on the MIL-DTL-3933 Qualified Products Database for at least one part, or provide evidence that their parts have passed the qualification requirements of MIL-DTL-3933. 3.8 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to

21、be an approved source of supply. 3.9 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and

22、promotes economically advantageous life cycle costs. 3.10 Workmanship. The attenuator shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Conformance in

23、spection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of the group A inspection of MIL-DTL-3933. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of

24、 materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defe

25、nse Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. Provided by IHSNot for ResaleNo reproduction o

26、r networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13015 REV PAGE 5 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Attenuators conf

27、orming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specification

28、s, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. 6.2 Ordering data. The contract or purchase order should specify the following: a.

29、Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for notification of change of product to the acquiring activ

30、ity, if applicable. d. Requirements for packaging and packing. 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop

31、under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on t

32、his matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.4 MIL-DTL-3933/18 replacements. The attenuators described herein are direct replacements for some of the MIL-DTL-3933/18 non-screened attenuators. TABLE II. Replacement data. MIL-DTL-3933/18 PIN DLA Land

33、and Maritime drawing PIN 13015- M3933/18-05N 05 1/ M3933 non-screened (N) PINs may also be known without the ending N character. 6.5 Replaceability. Attenuators covered by this drawing will replace the same commercial device covered by contractor prepared specification or drawing. 6.6 Users of recor

34、d. Coordination of this document for future revisions is coordinated only with the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, O

35、H 43218-3990, by email to tubesampsdla.mil, or by telephone (614) 692-0551 or DSN 850-0551. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13015 REV PAGE 6 6.7 Approved sources

36、 of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, contact DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990, by email to tubesampsdla.mil, or by telephone (614)

37、 692-0551 or DSN 850-0551. Vendor Vendor CAGE Vendor name and address Similar designation 1/ A 93459 Aeroflex/Weinschel Corporation 5305 Spectrum Drive 10146-30 Fredrick, MD 21703-7339 B 95077 SV Microwave 2400 Centrepark West Drive Suite 100 West Palm Beach, FL 33409-6469 SF0950-6002-05 1/ Parts must be purchased to the DLA Land and Maritime PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-