DLA AN107701 THRU AN107800 REV 3-1986 BOLT-CRES DRILLED HEX HEAD 6 HOLES 4375-20.pdf

《DLA AN107701 THRU AN107800 REV 3-1986 BOLT-CRES DRILLED HEX HEAD 6 HOLES 4375-20.pdf》由会员分享，可在线阅读，更多相关《DLA AN107701 THRU AN107800 REV 3-1986 BOLT-CRES DRILLED HEX HEAD 6 HOLES 4375-20.pdf（1页珍藏版）》请在麦多课文档分享上搜索。

1、k- - AN107702 THRU AN207B00 REV 3 53 7777725 0000287 B W I I .lo0 DIA CHAHFER 30 TO .625 DIA 6 HOLES SPACED AS SHOWN WITHIN .O20 (OPPOSITE SIDE OPTIONAL) OF TRUE POSITION L K PART NO. L K PART NO +. O00 +. 000 - .o60 - .o60 .e75 AN107708 1.750 .625 AN107722 107709 1.812 .688 AN107723 1:; i! AN107710

2、 1.675 .750 AN107724 1.062 AN107711 1.938 .E12 AN107725 AN107713 2.062 .938 AN107727 AN107714 2.125 1.000 AN107728 :;?: AN107715 2.250 1.125 AN107729 1.375 .250 AN107716 2.375 1.250 AN107730 107712 2.000 .875 AN107726 1.438 .3l2 AN107717 2.500 1.375 AN107731 1.500 .375 AN107718 2.625 1.500 AN107732

3、(e) THREAD TO HEAD. HAXIMUM TWO IHPERFECT THREADS. L - 2.750 2.875 3.000 3.125 3.250 3.375 3.500 3.625 3.750 3.875 4.000 4.125 4.250 4.375 K +.o00 - .o60 1.625 1.750 1.875 2.000 2.125 2.250 2 - 375 2.500 2.625 2.750 2.875 3.000 3.125 3.250 PART NO. AN107733 AN107734 AN107735 AN107736 AN107738 AN1077

4、37 AN107739 AN107740 AN107741 AN107742 AN107743 AN107744 AN107745 AN107746 - L - 4.500 4.625 4.750 4 875 5- 125 5.250 5.375 5.500 5 * 625 5.750 5 * 875 5.000 6.000 3.375 AN10774 3.500 AN10774 3.625 AA10774 3.750 AN10775 3.875 AN10775 4.000 AN10775 4.125 AN1775 4.250 AN10775 4.375 AN10775 4.500 AN107

5、75 4.625 AN10775 4.750 AN10775 4.W5 AN10775 NOTE: (I) SHANK SHALL BE STRAIGHT WITHIN .O025 FIR. PER INCH OF BOLT LENGTH. (2) THE CONCENTRICITY OF THREAD PD IN RELATION TO THE SHANK SHALL BE WITHIN .O06 FIR. (3) THE CONCENTRICITY OF THE SHANK IN RELATION TO THE WASHER FACE DIAMETER AND HEXAGON SHALL

6、BE WITHIN .O19 FIR. INACTIVE FOR DESIGN AFTER 27 DEC 1966 NO SUPERSEDING STANDARD. MATERIAL: CORROSION RESISTANT STEEL - SEE MANUFACTURING SPECIFICATION SURFACE ROUGHNESS: AS107 MANUFACTURING SPECIFICATION: AMS 7472 3 INSPECTION: ALL PARTS SHALL UNDERGO FLUOKESCENT PENETRANT INSPECTION IN ACCORDANCE

7、 YITH AMS2645. BREAK SHARP EDGES .o03 - .o15 UNLESS OTHERUISECPECIFIED. DIMENSIONS IN INCHES: UNLESS OTHERWISE SPECIFIED: TOLERANCES: LINEAR DIMENSIONS f.O1O, ANGULAR DO NOT USE UNASSIGNED PART NUMBERS. THIS STANDARD UAS DEVELOPED COOPERATIVELY YITH THE ENGINE AND PROPELLER UTILITY PARTS COMMITTEE O

8、F THE SAE DIMENSIONS i2 . AIR FORCE-NAVY AERONAUTICAL STANDARD AN I 0770 I AN I “TSO0 P.A. Ocher Cusr USAF - 11 Navy - AS BOLT - CRES DRILLED HEX HEAD. 6 HOLES. .4375 - 20 Army - AV THIS DOCUMENT CONTAINS -. i- PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-