DLA AN106801 THRU AN106900 REV 3-1986 BOLT - CRES DRILLED HEX HEAD 1 HOLE 4375-20 (INACTIVE AFTER 27 DEC 1966).pdf

《DLA AN106801 THRU AN106900 REV 3-1986 BOLT - CRES DRILLED HEX HEAD 1 HOLE 4375-20 (INACTIVE AFTER 27 DEC 1966).pdf》由会员分享，可在线阅读，更多相关《DLA AN106801 THRU AN106900 REV 3-1986 BOLT - CRES DRILLED HEX HEAD 1 HOLE 4375-20 (INACTIVE AFTER 27 DEC 1966).pdf（1页珍藏版）》请在麦多课文档分享上搜索。

1、AN306801 THRU AN306700 REV 3 53 M 7777735 0000278 7 M b #17* i9 FED, SUP CLASS 5306 MATERIAL IDENTIPICATION PER AMs2800. RAISED OR DEPRESSED .o10 MAX 1.562 E I AN106806 11 1.625 : 8?2“ AN106807 1.688 106808 i. 50 :% I I AN106809 II 1:812 o00 AN106810 1 875 .o62 106811 i. 938 106812 .2.000 :i% /il AN

2、106813 2.062 AN106 14 2.125 .312 !:i8 AN106!15 2.250 .375 .250 AN106816 2.375 I .250 OHANFER 30 TO .625 DIA (OPPOSITE SIDE OFTIORAL) +.o00 .438 106819 .562 106821 -500 I AN106820 ,625 106822 .688 AN106823 .750 AN106824 .812 AN106825 .938 AN106827 1.125 AN106829 1.250 AN106830 ,875 106826 i. o00 1068

3、28 1.375 AN106831 1.500 I AN106832 L 2.750 2.875 3.000 3.125 3.250 3.375 3.500 3 * 625 3 750 i:% 4.125 4.250 4.375 K PART NO. +.o00 - .o60 1.625 AN106833 1. 50 AN106834 1.875 AN106835 2.125 AN10683 2.250 AN10683g 2.375 AN106839 2.500 AN106840 2.625 AN106841 2.750 AN106842 2.875 AN106843 3.000 AN1068

4、44 3.125 AN106845 3.250 AN106846 2.000 106836 L K +.o00 - .o60 - 4i500 3.375 4.625 3.500 4,875 3.750 5.000 3.875 5.125 4.000 5.250 4.125 4.750 3.625 5.375 4.250 5.500 4.375 5.625 4.500 4.625 4.750 6.000 4.875 PART NO. AN106849 AN106850 106851 106852 AN106853 AN106854 AN106855 AN106856 AN106857 AN 1

5、O 68 5 8 AN106859 (a) THREAD TO HEAD. MAXIMUM TWO MPERFECT THREADS, NOTE: (I) SHANK SHALL BE STRAIGHT WITHIN.0025FIR. PER INCH OF BOLT LENGTH. (2) THE CONCENTRICITY OF THREAD PD IN RELATION TO THE SHANK SHALL BE WITHIN .O06 FIR. (3) THE CONCENTRICITY OF THE SHANK IN RELATION TO THE WASHER FACE DIAME

6、TER AND HEXAGON SHALL BE WITHIN .O19 FIR. INACTIVE FOR DESIGN AFTER 27DEC 1966 NO SUPERSEDING STANDARD. MATERIAL: CORROSLON RESISTANT STEEL - SEE MANUFACTURING SPECIFICATION SURFACE ROUGHNESS: AS107 MANUFACTURING SPECIFICATION: AMS 7472 BREAK SHARP EDGES .003-.O15 UNLESS OTHERWISE SPECIFIED. DIMENSI

7、ONS IN INCHES. UNLESS OTHERWISE SPECIFIED: TOLERANCES; LINEAR DIMENSIONS t.010. ANGULAR DO NOT USE UNASSIGNED PART NUMBERS. THIS STANDARD WAS DEVELOPED COOPERATIVELY WITH THE ENGINE AND PROPELLER UTILITY PARTS COMMITTEE OF THE SAE. ) INSPECTION: ALL PARTS SHALL UNDERGO FLUORESCENT PENETRANT INSPECTION IN ACCORDANCE WITH AMS2645. DIMENSIONS 22. P.A. Ocher Cusc USAF - II Navy - AS Army - AV AIR FORCE-NAVY AERONAUTICAL STANDARD - BOLT - CRES DRILLED HEX HEAD, 1 HOLE, .4375-20 AN106801 ANRGUQOO Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-