DLA A-A-59920-2012 FUSEHOLDER EXTRACTOR POST IN-LINE NON-CRIMP TYPE ACCOMMODATES 75 INCH 19 05 MILLIMETER (MM) TO 1 25 INCH (31 75 MM) LONG FUSES CARTRIDGES.pdf

《DLA A-A-59920-2012 FUSEHOLDER EXTRACTOR POST IN-LINE NON-CRIMP TYPE ACCOMMODATES 75 INCH 19 05 MILLIMETER (MM) TO 1 25 INCH (31 75 MM) LONG FUSES CARTRIDGES.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59920-2012 FUSEHOLDER EXTRACTOR POST IN-LINE NON-CRIMP TYPE ACCOMMODATES 75 INCH 19 05 MILLIMETER (MM) TO 1 25 INCH (31 75 MM) LONG FUSES CARTRIDGES.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any data which may improve this document should be sent to: DLA Land and Maritime, ATTN: VAT, P.O. Box 3990, Columbus, OH 43218-3990, or email mailto:CircuitProtectdla.mil. Since contact information can change you

2、may want to verify the currency of the address information using the ASSIST Online database at https:/assist.dla.mil AMSC N/A FSC 5920 INCH-POUND A-A-59920 20 December 2012 COMMERCIAL ITEM DESCRIPTION FUSEHOLDER, EXTRACTOR POST, IN-LINE, NON-CRIMP TYPE, ACCOMMODATES .75 INCH 19.05 MILLIMETER (MM) TO

3、 1.25 INCH (31.75 MM) LONG FUSES CARTRIDGES The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers the general requirements for a non-crimp type, in-line fuseholder extractor pos

4、t that accommodates .75 inch (19.05 mm) to 1.25 inch (31.75 mm) long fuse cartridges. Fuseholders covered by this CID are intended for commercial/industrial applications. 2. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This CID uses a classification system that is included in the PIN. The PIN

5、 shall be AA59920-001 (see 7.1) 3. SALIENT CHARACTERISTICS. 3.1 Interface and physical dimensions. Fuseholders supplied to this CID shall be as specified herein (see figure 1). Ampere rating. The ampere rating shall be 30 amperes. Voltage rating. The voltage rating shall be 600 V ac. Fuseholder body

6、 material. The fuseholder body material shall be white Nylon 66. Terminal plating. Terminals shall be tin plated brass. Use of pure tin plating is prohibited as a final finish and as an undercoat. Use of tin-lead (Sn-Pb) finishes are acceptable provided that the minimum lead content is 3 percent. Op

7、erating temperature. The operating temperature shall be -55C to +120C. Non-Crimping. This is a no crimp in line fuseholder. 3.6 Marking. Fuseholders supplied to this CID shall be marked with the manufacturers (MFRs) standard commercial PIN. (NOTE: The part number marked on the unit pack shall be the

8、 CID PIN.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59920 2 Ltr Inches mm Min Max Min Max A 0.725 0.735 18.42 18.67 B 2.225 2.235 56.52 56.77 NOTES: 1. Dimensions are in Inches. 2. Tolerance is 0.13 mm (0.005 inch), unless otherwise specif

9、ied. FIGURE 1. Configuration and dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59920 3 TABLE I. Electrical Characteristics. CID dash number AA59920- Ampere rating Terminals Fuse accommodation 001 30 amperes maximum Terminals will ac

10、cept #12 - 18 AWG standard wire. Accommodates .25 inch (6.25mm) diameter fuses cartridges with lengths of .75 inch (19.05 mm) to 1.25 inch (31.75mm). 3.7 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the m

11、aximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.8 Workmanship. Fuseholders shall be processed in such a manner as to be uniform in quality and shall be free from other defects

12、that will affect life, serviceability, or appearance. 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product co

13、nformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The Government reserves the right to require proo

14、f of such conformance. 5.2 Market acceptance. The following market acceptance criteria are necessary to document the quality of the product to be provided under this CID: a. The company producing the item must have been producing a product meeting the requirements of this CID for at least 2 years. b

15、. The company must have sold 1,000 units meeting this CID in the commercial marketplace over the past 2 years. 6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES. 7.1 PIN. The PIN should be used for Government purposes to buy commercial products

16、 to this CID. See section 2 for PIN format example. 7.2 Environmentally preferable materials. Environmentally preferable materials should be used to the maximum extent possible to meet the requirements of this specification. As of the dating of this document, the U.S. Environmental Protection Agency

17、 (EPA) is focusing efforts on reducing 31 priority chemicals. The list of chemicals and additional information is available on their website http:/www.epa.gov/osw/hazard/wastemin/priority.htm. Included in the EPA list of 31 priority chemicals are cadmium, lead, and mercury. Use of these materials sh

18、ould be minimized or eliminated unless needed to meet the requirements specified herein (see Section 3). 7.3 Commercial and Government Entity (CAGE) code. For ordering purposes, inventory control, and submission of these fuseholders to DLA Land and Maritime under the Military Parts Control Advisory

19、Group (MPCAG) evaluation program, CAGE code 58536 should be used. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59920 4 7.4 Source of documents. FEDERAL REGULATIONS FAR - Federal Acquisition Regulations (FAR) (Copies of this document are availa

20、ble online at http:/www.acquisition.gov/comp/far/index.html or from the U.S. Government Printing Office, 732 N. Capital Street, NW, Washington D.C. 20401-0001.) 7.5 Ordering data. The contract or order should specify the following: a. CID document number, revision, and CID PIN. b. Product conformanc

21、e provisions. c. Packaging requirements. 7.6 Commercial products. As part of the market analysis and research effort, this CID was coordinated with the following manufacturers of commercial products. At the time of CID preparation and coordination, these manufacturers were known to have commercial p

22、roducts that would meet the requirements of this CID. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict acquisition to only the manufacturers shown.) MFRs CAGE MFRs name and address 1SK21 Posi-Products, Incorporated P.O. Box 3042 St. Augustin

23、e, Florida 32085-3042 Phone number (800) 785-2330 E-mail: mailto: serviceposi- Uniform Resource Locator (URL): http:/www.posi- 7.7 Part number (P/N) supersession data. This CID specification sheet part number supersedes the following MFRs P/N as shown. This information is being provided to assist in

24、 reducing proliferation in the Government inventory system. TABLE III. P/N supersession data. CID dash number AA59920- (see table I) MFRs CAGE MFRs P/N 1/ 001 1SK21 619 1/ The manufacturers P/N shall not be used for acquisition to the requirements of this CID specification sheet. At the time of prep

25、aration of this CID specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID P/N shown. For actual part marking requirements see 3.6. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59920 5 7.9 Go

26、vernment users. To acquire information on obtaining these fuseholders from the Government inventory system, contact DLA Land and Maritime, ATTN: DLA Land and Maritime-FMX, P.O. Box 3990, Columbus, OH 43218-3990, or telephone (614) 692-3677. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: GSA

27、 - FAS Custodians: Navy - EC Preparing activity: DLA - CC DLA-CC Project 5920-2012-074 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-