DLA A-A-55504 5 C-2011 FUSEHOLDER EXTRACTOR POST FRONT MOUNT LOW PROFILE SCREWDRIVER KNOB FUSE CARRIER FOR 3AG ( 25 INCH (IN) X 1 25 IN (6 35 MILLIMETERS (MM) X 31 75 MM)) OR 196 I.pdf

《DLA A-A-55504 5 C-2011 FUSEHOLDER EXTRACTOR POST FRONT MOUNT LOW PROFILE SCREWDRIVER KNOB FUSE CARRIER FOR 3AG ( 25 INCH (IN) X 1 25 IN (6 35 MILLIMETERS (MM) X 31 75 MM)) OR 196 I.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-55504 5 C-2011 FUSEHOLDER EXTRACTOR POST FRONT MOUNT LOW PROFILE SCREWDRIVER KNOB FUSE CARRIER FOR 3AG ( 25 INCH (IN) X 1 25 IN (6 35 MILLIMETERS (MM) X 31 75 MM)) OR 196 I.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5920 INCH-POUND A-A-55504/5C 9 May 2011 SUPERSEDING A-A-55504/5B 20 January 2006 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET FUSEHOLDER, EXTRACTOR POST, FRONT MOUNT, LOW PROFILE, SCREWDRIVER KNOB FUSE CARRIER FOR 3AG (.25 INCH (IN) X 1.25 IN (6.35 MILLIMETERS (MM) X 31.75 MM) OR .19

2、6 IN X .787 IN (5 MM X 20 MM) FUSE CARTRIDGES The General Services Administration has authorized the use of this commercial item description (CID) for all federal agencies. The complete requirements for procuring the fuseholders described herein shall consist of this document and the issue in effect

3、 of CID A-A-55504. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This commercial item description (CID) specification sheet uses a classification system which is included in the PIN as shown in the following example (see NOTES). AA55504/05- Accommodates fuse Rear terminal configuration 001A 3A

4、G A 001B 3AG B 001C 3AG C 001D 3AG D 002A 5 mm x 20 mm A 002B 5 mm x 20 mm B 002C 5 mm x 20 mm C 002D 5 mm x 20 mm D SALIENT CHARACTERISTICS. Interface and physical dimensions. Fuseholders supplied to this CID specification sheet shall be as specified herein (see figure 1). Rear terminal configurati

5、on. The rear terminal configuration shall be as specified in A-A-55504. Mounting hole. The mounting hole shall be as specified in figure 1. NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See classification information for PIN fo

6、rmat example. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55504/5C 2 NOTES: 1. Dimensions are in inches. 2. Unless otherwise specified, tolerance is .005 inch (0.13 mm). FIGURE 1. Configuration and dimensions. Inches mm Inches mm .030 0.76 .4

7、68 11.90 .039 1.01 .489 12.19 .150 3.81 .500 12.70 .180 4.57 .509 12.95 .250 6.35 .627 15.95 .255 6.48 .692 17.60 .311 7.90 1.476 37.50 .457 11.60 1.539 40.23 .465 11.81 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55504/5C 3 Commercial produc

8、ts. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would mee

9、t the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict acquisition to only the manufacturers shown.) MFRs CAGE MFRs name and address 71400 Cooper Bussmann, Incorporated P. O. Box 14460 St. Louis,

10、 MO 63178-4460 Phone number (636) 394-2877 Facsimile number (800) 544-2570 E-mail: mailto: Uniform Resource Locator (URL): https:/ 75915 Littelfuse Incorporated 8755 West Higgins Road, Suite 500 Chicago, IL 60631-2701 Phone number (847) 824-1188 Facsimile number (847) 391-0894 E-mail: mailto: URL: h

11、ttps:/ Part number (P/N) supersession data. These CID specification sheet PINs supersede the following MFRs P/Ns as shown. This information is being provided to assist in reducing proliferation in the Government inventory system. TABLE I. P/N supersession data. CID dash number AA55504/05- (see table

12、 I) MFRs CAGE 71400 MFRs CAGE 75915 MFRs P/N 1/ MFRs P/N 1/ 001A HTB-32I 3453LS2 001B HTB-34I 3453LS1 001C HTB-36I 3453LS8 001D HTB-38I 3453LS7 002A HTB-32M 3455LS2 002B HTB-34M 3455LS1 002C HTB-36M 3455LS8 002D HTB-38M 3455LS7 1/ The manufacturers P/N shall not be used for acquisition to the requir

13、ements of this CID specification sheet. At the time of preparation of this CID specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID P/N shown. For actual part marking requirements see the marking paragraph of A-A-55504. Provided by IHSNot for Res

14、aleNo reproduction or networking permitted without license from IHS-,-,-A-A-55504/5C 4 National stock number (NSN). The following is a list of NSNs assigned which correspond to this CID specification sheet. The list is for information only and may not be indicative of all possible NSNs associated wi

15、th the CID specification sheet. For up to date information on assigned NSNs, please contact the aforementioned DLA Land and Maritime office (See A-A-55504). TABLE II. NSNs. Dash number (see table I) AA55504/05- NSN 001A N/A 001B 5920-01-233-4244 001C N/A 001D N/A 002A N/A 002B 5920-01-362-5183 002C

16、N/A 002D N/A Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extensiveness of the changes. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: GSA - FAS Custodians: Navy - EC Preparing activity: DLA -

17、 CC DLA-CC Project 5920-2011-024 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-