DLA A-A-51195 B-2011 PRESS ARBOR C FRAME HYDRAULIC HAND OPERATED.pdf

《DLA A-A-51195 B-2011 PRESS ARBOR C FRAME HYDRAULIC HAND OPERATED.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-51195 B-2011 PRESS ARBOR C FRAME HYDRAULIC HAND OPERATED.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: STDZNMGTdla.mil or Defense Logistics Agency Aviation VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616. Since contact information can change, you m

2、ay want to verify the currency of this address information using the ASSIST database at https:/assist.daps.dla.mil/. FSC 3444 INCH-POUND A-A-51195B 13 April 2011 SUPERSEDING A-A-51195A 2 June 1998 COMMERCIAL ITEM DESCRIPTION PRESS, ARBOR, “C“ FRAME HYDRAULIC, HAND OPERATED The General Services Admin

3、istration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers both “C“ (gap) and “4“ post frame type hydraulic bench- or pedestal-mounted, hand-operated, arbor presses of the standard commercial type, which are

4、used to force arbors into and out of holes or to assemble and disassemble press fit parts. 2. CLASSIFICATION. The arbor presses shall be classified by the following types and sizes: 2.1 Type. The arbor press shall be one of the following types, as specified (see (7.3(c): Type I - “C“ (gap) frame Typ

5、e II - “4“ post frame 2.2 Size. The arbor press shall be one of the following sizes, as specified (see (7.3(d): Size 10 - 10 ton Size 25 - 25 ton Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-51195B 2 3. SALIENT CHARACTERISTICS 3.1 Frame. The f

6、rame shall be of the “C“ (gap) or “4“ post frame type. When only one style of frame is acceptable, the particular style required shall be specified in the acquisition order (see 7.3(c). The frame shall support the hydraulic system and ram assembly. The frame shall provide a means for securing the pr

7、ess to a bench or pedestal. The ram shall be perpendicular to the table surface to an accuracy of 0.025 inch total indicator reading per 6 inches of ram travel. The table shall have an opening aligned with the ram axis that will allow passage of the arbor. 3.2 Hydraulic system. The hydraulic system

8、shall consist of a hand-operated pump, a fluid reservoir, a cylinder with ram, and the necessary fittings and hoses to ensure a complete hydraulic system. Unless otherwise specified in the acquisition order (see 7.3(e), the system shall be equipped with a single acting cylinder. The system shall hav

9、e overload protection and a means of preventing extension of the ram beyond its normal end-of-stroke position. Unless otherwise specified in the acquisition order (see 7.3(f), the stroke length of the ram shall be 10.125 inches. A pressure gauge calibrated to read tons of ram force shall be provided

10、. 3.3 Bolster plate. The “C“ (gap) frame presses shall be provided with a circular bolster plate having not less than four equally spaced slots of varying widths for the passage of an arbor. The bolster plate shall be removable and shall allow the desired plate slot to be positioned below the ram. 3

11、.4 Radius of work. The radius of work is defined as the distance from the center of the ram to the frame. Unless otherwise specified in the acquisition order (see 7.3(g), the radius of work for the press to be furnished shall be selected from table I. The tolerance of the radius of work shall be 0.5

12、 inch. TABLE I. Radius of work. Radius of work designation Radius of work (in) A 6.500 B 8.000 C 9.000 D 9.500 NOTE: Largest diameter of work is two times the radius. The radius of work designation is for use in developing the CID-based part or identification number only (see 7.1). 3.5 Vertical capa

13、city. The vertical capacity is defined as the distance when measured from top of table surface to ram (ram up). Unless otherwise specified in the acquisition order (see 7.3(h), the vertical capacity for the press to be furnished shall be as specified and selected from table II. The tolerance of the

14、vertical capacity shall be 1.0 inch. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-51195B 3 TABLE II. Vertical capacity. Vertical capacity designation Distance ram to table (in) 1 9.500 2 15.000 3 15.375 4 16.500 5 20.250 NOTE: The vertical cap

15、acity designation is for use in developing the CID-based part or identification number only (see 7.1). 3.6 Metric products. Products manufactured to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, provided they fall within specified tolerances u

16、sing conversion tables contained in the latest revision of FED-STD-376, “Preferred Metric Units for General use by the Federal Government“, and all other requirements of this CID are met. 4. REGULATORY REQUIREMENTS 4.1 Recovered materials. The offeror/contractor is encouraged to use recovered materi

17、als to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4.2 Environmental protection. During the manufacture of the press, materials hazardous to the ecological systems as prohibited by the Federal, State, or local statutes in effect on

18、 the date of the contract shall not be used or emitted. 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the s

19、ame product offered for sale in the commercial marketplace. The government reserves the right to require proof of such conformance. 5.2 Market acceptability. The products offered must have been previously sold either to the government or on the commercial market. 6. PACKAGING 6.1 Preservation, packi

20、ng, and marking. Preservation, packing, and marking shall be as specified in the acquisition order (see 7.3(i). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-51195B 4 7. NOTES 7.1 Part or identification number (PIN). The following PIN procedure

21、 is for government purposes and does not constitute a requirement for the contractor. AA51195 - X XX X X Vertical capacity: 1 - 9.500 inch 2 15.000 inch 3 15.375 inch 4 - 16.500 inch 5 20.250 inch Radius of work: A - 6.500 inch B 8.000 inch C 9.000 inch D - 9.500 inch Size: 10 - 10 ton 25 25 Type: A

22、 - Type I - “C“ (gap) frame B - Type II - “4“ post frame CID Number Example of reference part number: AA51195 - A10D5 7.2 Sources of documents. 7.2.1 FAR. The FAR may be obtained from the Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954. Electronic copies may be obtained from

23、https:/www.acquisition.gov/far/. 7.2.2 Federal standards. Copies of federal standards may be obtained from General Services Administration, Federal Supply Service, Specification Section, 470 East LEnfant Plaza SW, Suite 8100, Washington, DC 20407. Electronic copies may be obtained from https:/assist

24、.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-51195B 5 7.3 Ordering data. The acquisition order should specify the following information: a. CID document number, revision, and CID PIN. b. Quantity required. c. Type (see 2.1 and

25、3.1). d. Size (see 2.2). e. Dual acting cylinder, if required (see 3.2). f. Stroke length, if different (see 3.2). g. Radius of work, if different (see 3.4). h. Vertical capacity, if different (see 3.5). i. Preservation, packing, and marking (see 6.1). 7.4 Intended use. Arbor presses covered by this

26、 CID are for use in machine production, repair, and maintenance shops. 7.5 Subject term (key word) listing. Bench Bolster Cylinder Pedestal Ram MILITARY INTERESTS: Custodians: Army - AR Navy - SH Air Force - 99 DLA - GS Review Activities: Navy - YD Air Force - 84 Preparing Activity: DLA - GS6 (Proje

27、ct 3444-2011-001) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-