DIN SPEC 19674-2-2011 Plastics piping systems made from glass fibre reinforced polyethylene (PE-GF) for water supply and for drainage and sewerage under pressure - Part 2 Pipes《供水 .pdf

《DIN SPEC 19674-2-2011 Plastics piping systems made from glass fibre reinforced polyethylene (PE-GF) for water supply and for drainage and sewerage under pressure - Part 2 Pipes《供水 .pdf》由会员分享，可在线阅读，更多相关《DIN SPEC 19674-2-2011 Plastics piping systems made from glass fibre reinforced polyethylene (PE-GF) for water supply and for drainage and sewerage under pressure - Part 2 Pipes《供水 .pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、February 2011English price group 11ICS 23.040.20!$nwg“1758468www.din.deDDIN SPEC 19674-2Plastics piping systems made from glass fibre reinforced polyethylene(PE-GF) for water supply and for drainage and sewerage underpressure Part 2: PipesEnglish translation of DIN SPEC 19674-2:2011-02Kunststoff-Roh

2、rleitungssysteme aus glasfaserverstrktem Polyethylen (PE-GF) fr dieWasserversorgung und fr Entwsserungs- und Abwasserdruckleitungen Teil 2: RohreEnglische bersetzung von DIN SPEC 19674-2:2011-02www.beuth.deDocument comprises 20 pagesTraduction anglaise de DIN SPEC 19674-2:2011-02 Normenausschuss Was

3、serwesen (NAW) im DIN Bereich Innovation Systmes de canalisations en plastique en polythylne renforc de fibres de verre(PE-GF) pour lalimentation en eau, pour branchements et collecteurs dassainissementavec pression Partie 2: TubesThere are various procedures for developing a DIN SPEC: This document

4、 has been developed in accordance with the PAS procedure. No part of this specification may be reproduced without prior permission of DIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany, has the exclusive right of sale for specifications. DIN SPEC 19674-2:2011-0

5、2 Contents Page Foreword. 3 Introduction 4 1 Scope 4 2 Normative references 5 3 Terms, definitions, symbols and abbreviated terms 6 4 Material. 6 4.1 PE compound 6 4.2 Extrusion compound. 6 4.3 Glass fibres 6 4.4 Primer . 6 4.5 Compound for the identification of pipes . 6 4.6 Appearance 6 4.7 Colour

6、. 7 4.8 Effects on the quality of water . 7 5 Geometrical characteristics . 7 5.1 Measurements . 7 5.2 Mean inside diameter, out-of-roundness (ovality) 7 5.3 Wall thicknesses and their tolerances 8 5.4 Lengths 12 5.5 Bending radius of welded pipes 12 6 Mechanical characteristics. 12 6.1 Conditioning

7、 12 6.2 Requirements. 13 7 Physical characteristics 14 7.1 Conditioning 14 7.2 Requirements. 14 8 Chemical characteristics of pipes in contact with chemicals . 15 9 Performance requirements regarding the fitness for purpose of the piping system 15 10 Marking. 15 10.1 General . 15 10.2 Minimum requir

8、ed marking of pipes . 16 Annex A (informative) Bending radius of welded pipes 17 Annex B (informative) Ring stiffnes 18 Bibliography . 20 2 A comma is used as the decimal marker. DIN SPEC 19674-2:2011-02 Foreword This Publicly Available Specification DIN SPEC (PAS) serves as an addition to existing

9、standards and directives and applies in particular for plastics piping systems made from glass fibre reinforced polyethylene (PE-GF). It defines requirements not yet included in any relevant standard, since the material covered is new. This topic is also subject of worldwide standardization activiti

10、es (ISO/CD 29561, ASTM F 2720/F 2720M). The publication of this DIN SPEC has been supervised by NAW (Water Practice Standards Committee) of DIN (Deutsches Institut fr Normung e. V.). The authors are entirely responsible for the contents of this document. The authors of this document are: Christoph F

11、itten; Krah AG Stephan Fllgrabe; PlaspiTec GmbH Maik Ginsberg; Ingenieurbro Mller GmbH SGBD Deutschland GmbH Cagatay Tulunay; FIRAT Plastik A.S. Prof. Philippe Vanspeybroeck; BECETEL vzw DIN SPEC 19674 consists of the following parts under the general title Plastics piping systems made from glass fi

12、bre reinforced polyethylene (PE-GF) for water supply and for drainage and sewerage under pressure: Part 1: General Part 2: Pipes (this part) Part 3: Fittings (in preparation) Part 4: Fitness for purpose of the system (in preparation) DIN SPEC are not included in the set of German standards. DIN Deut

13、sches Institut fr Normung e. V. Normenausschuss Wasserwesen (NAW) 2010-11-01 3 DIN SPEC 19674-2:2011-02 Introduction This DIN SPEC is the result of the work of a group of experts consisting of experienced representatives of the plastics industry. The DIN SPEC is intended to be a step on the way to f

14、urther standardization in an area not yet covered by any DIN standard. The individual user is responsible for verifying whether the DIN SPEC is suitable for his purpose and whether the current level of knowledge is taken into account. DIN SPEC 19674 specifies the requirements for a piping system and

15、 its components made from glass fibre reinforced polyethylene (PE-GF). The piping system is intended to be used for water supply, including the conveyance of raw water prior to treatment, for drainage and sewerage under pressure, vacuum sewerage systems, and for systems for the conveyance of water f

16、or general purposes. With respect to the possible effects of products in accordance with DIN SPEC 19674 on the quality of water for human consumption (potable water), the following shall be considered: a) this specification does not indicate whether the products may be used without restrictions; b)

17、products intended for use in water supply systems shall conform to national regulations and to test requirements which ensure the fitness for purpose regarding the contact with water for human consumption. For compounds, the requirements and test methods of DIN SPEC 19674-1 apply. This part of DIN S

18、PEC 19674 specifies the characteristics of pipes made from glass fibre reinforced polyethylene (PE-GF). 1 Scope This part of DIN SPEC 19674 specifies the requirements for pipes made from glass fibre reinforced polyethylene (PE-GF) for pressure piping systems (main and connecting pipes) intended for

19、the conveyance of water for human consumption, including raw water prior to treatment, for drainage and sewerage under pressure, vacuum sewerage systems, and for systems for the conveyance of water for general purposes. NOTE 1 In this specification, DN refers to the inside diameter of pipes and fitt

20、ings. It also specifies the test parameters for the test methods referred to in this specification. In conjunction with the other parts of DIN SPEC 19674, it applies to pipes from PE-GF, their joints with each other, with other PE-GF components, and to components from other materials intended for us

21、e under the following conditions: a) a maximum allowable operating pressure (MOP) up to and including 22 bar; b) an operating temperature of 20 C as the reference temperature. NOTE 2 DIN SPEC 19674 includes specifications for maximum allowable operating pressures and specifies requirements for the c

22、olour of components and the use of additives. It is the responsibility of the purchaser or specifier to make the appropriate selection from these criteria while taking into account their own particular requirements as well as any relevant national guidelines or regulations and installation practices

23、 or codes. NOTE 3 For applications at constant operating temperatures higher than 20 C and up to 40 C, see DIN SPEC 19674-1, Annex A. 4 DIN SPEC 19674-2:2011-02 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, onl

24、y the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. DIN SPEC 19674-1, Plastics piping systems made from glass fibre reinforced polyethylene (PE-GF) for water supply and for drainage and sewerage under pressure Part 1:

25、 General DIN SPEC 19674-4, Plastics piping systems made from glass fibre reinforced polyethylene (PE-GF) for water supply and for drainage and sewerage under pressure Part 4: Fitness for purpose of the system (to be published) DIN Technical Report CEN/TR 15438, Plastics piping systems Guidance for c

26、oding of products and their intended uses DIN EN 12201-1, Plastics piping systems for water supply Polyethylene (PE) Part 1: General DIN EN ISO 1167-1, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General meth

27、od DIN EN ISO 1167-2, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 2: Preparation of pipe test pieces DIN EN ISO 2078, Textile glass Yarns Designation DIN EN ISO 2505, Thermoplastics pipes Longitudinal reversion

28、Test methods and parameters DIN EN ISO 3126, Plastics piping systems Plastics components Determination of dimensions DIN EN ISO 6259-1, Thermoplastics pipes Determination of tensile properties Part 1: General test method DIN EN ISO 9080, Plastics piping and ducting systems Determination of the long-

29、term hydrostatic strength of thermoplastics materials in pipe form by extrapolation ISO 3344, Reinforcement products Determination of moisture content ISO 4065, Thermoplastics pipes Universal wall thickness table ISO 4433-1, Thermoplastics pipes Resistance to liquid chemicals Classification Part 1:

30、Immersion test method ISO 4433-2, Thermoplastics pipes Resistance to liquid chemicals Classification Part 2: Polyolefin pipes ISO 6259-3, Thermoplastics pipes Determination of tensile properties Part 3: Polyolefin pipes ISO 11357-6: Plastics Differential scanning calorimetry (DSC) Part 6: Determinat

31、ion of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) ISO 11922-1, Thermoplastics pipes for the conveyance of fluids Dimensions and tolerances Part 1: Metric series 5 DIN SPEC 19674-2:2011-02 3 Terms, definitions, symbols and abbreviated terms For the pur

32、poses of this document, the terms, definitions, symbols and abbreviated terms given in DIN SPEC 19674-1 apply. 4 Material 4.1 PE compound The PE compound (PE 80 or PE 100), from which the extrusion compound is manufactured, shall meet the minimum requirements of DIN EN 12201-1 and shall be evaluated

33、 on the basis of DIN EN ISO 9080. All additives used shall be uniformly dispersed in the PE compound. For all additives used, national legislation shall apply. Non-pigmented PE compounds may be used subject to special agreement between manufacturer and purchaser if required by the application. 4.2 E

34、xtrusion compound The extrusion compound (PE compound, glass fibres, bonding agent), from which the pipes and fittings are manufactured, shall be produced by mixing PE compound, glass fibres, and bonding agent with all the additives required for manufacture and final use in accordance with the requi

35、rements specified in DIN SPEC 19674-1. The fitness for purpose shall be demonstrated for the manufactured pipe by the manufacturer of the extrusion compound according to DIN EN ISO 9080 and the requirements given in Table 3 of DIN SPEC 19674-1: 2011-02. 4.3 Glass fibres The glass fibres used for the

36、 manufacture of the extrusion compound shall meet the requirements listed in DIN SPEC 19674-1:2011-02, Table 1 and DIN EN ISO 2078. Other types of glass may be used provided they meet the requirements of the relevant parts of this specification. 4.4 Primer The primer used for the production of the e

37、xtrusion compound shall meet the requirements listed in Table 2 of DIN SPEC 19674-1. 4.5 Compound for the identification of pipes The compound used for the stripes or co-extruded layers for the purpose of pipe identification shall consist of the same polymer as the PE compound used for the productio

38、n of the extrusion compound. 4.6 Appearance When viewed without magnification, the internal and external surfaces of pipes shall be smooth and clean and shall have no scoring, cavities, and other surface defects to an extent that would prevent conformity to this standard. 6 DIN SPEC 19674-2:2011-02

39、The ends of the pipe shall be cut cleanly and square to the axis of the pipe. Surface irregularities due to production processes are acceptable. 4.7 Colour Pipes intended for the conveyance of water for human consumption shall be black or blue. In addition, black pipes may be identified by blue stri

40、pes according to national preference. Blue pipes or black pipes with blue stripes are only intended for the conveyance of water for human consumption. Pipes intended for the conveyance of water for general purposes as well as drainage and sewerage shall be black or black with brown stripes according

41、 to national regulations. 4.8 Effects on the quality of water Compounds used for products intended for the supply of water for human consumption shall conform to existing national regulations as well as test requirements ensuring the fitness for purpose regarding the contact with potable water. 5 Ge

42、ometrical characteristics 5.1 Measurements The dimensions of the pipe shall be measured in accordance with DIN EN ISO 3126. In case of dispute, the dimensions shall be determined at least 24 h after manufacture and after conditioning at (23 2) C for at least 4 h. 5.2 Mean inside diameter, out-of-rou

43、ndness (ovality) The mean inside diameter, dim, and the out-of-roundness (ovality) shall conform to Table 1. 7 DIN SPEC 19674-2:2011-02 Table 1 Mean inside diameter and out-of-roundness (ovality) Dimensions in millimetres Nominal inside diameter Mean inside diameter Nominal size DN/ID dindim,mindim,

44、maxaMaximum value for out-of-roundness (ovality)b300 300 300 308 10 400 400 400 408 14 500 500 500 508 17 600 600 600 610 21 700 700 700 711 24 800 800 800 813 28 900 900 900 915 31 1000 1 000 1 000 1 017 35 1100 1 100 1 100 1 119 38 1200 1 200 1 200 1 220 42 1300 1 300 1 300 1 322 45 1400 1 400 1 4

45、00 1 423 49 1500 1 500 1 500 1 525 53 1600 1 600 1 600 1 627 56 1800 1 800 1 800 1 830 63 2000 2 000 2 000 2 034 70 2200 2 200 2 200 2 237 77 2400 2 400 2 400 2 440 84 2600 2 600 2 600 2 644 91 2800 2 800 2 800 2 847 98 3 000 3 000 3 000 3 051 105 3200 3 200 3 200 3 254 112 3400 3 400 3 400 3 457 11

46、9 3600 3 600 3 600 3 661 126 3800 3 800 3 800 3 864 133 4000 4 000 4 000 4 068 140 Tolerances for intermediate diameters can be calculated using the equation given below. Values are rounded off to the next 1 mm. adim,max= din+ (din 0,017), but din+ 8 mm. bThe maximum value for out-of-roundness (oval

47、ity) is calculated according to ISO 11922-1.5.3 Wall thicknesses and their tolerances The wall thickness in the area between the socket and spigot of a pipe shall meet the requirements listed in Table 2 and includes the internal and external co-extruded layers for colouration, UV protection, and pro

48、tection against degradation due to chemical attack. Alternatively, other diameters and pressures may be used. The corresponding wall thickness shall then be calculated using the given equation. NOTE The relationship between MRS (see DIN SPEC 19674-1:2011-02, Table 5), PN, SID, and SIDR is indicated

49、in Table 2. 8 DIN SPEC 19674-2:2011-02 Table 2 Wall thicknesses and related nominal pressures Dimensions in millimetres Pipe series SIDR 10 SIDR 11,5 SIDR 12,5 SIDR 14,5 SID5,5 SID6,25 SID6,75 SID7,75 Designation/MRS Nominal pressure, PN, in bar PE-GF 160/16 PN 18 PN 16 PN 14 PN 12,5 PE-GF 180/18 PN 20 PN 18 PN 16 PN 14 PE-GF 200/20 PN 22 PN 20 PN 18 PN 16 Wall thickness Nominal size DN/ID eminemaxeminemaxeminemaxeminemax300 30,0 33,2 26,1 28,9 24,0 26,6 20,7 22,9 400 40,0 44,2