DIN EN ISO 25239-5-2012 Friction stir welding - Aluminium - Part 5 Quality and inspection requirements (ISO 25239-5 2011) German version EN ISO 25239-5 2011《摩擦搅拌焊 铝 第5部分 质量和检查要求(IS.pdf

《DIN EN ISO 25239-5-2012 Friction stir welding - Aluminium - Part 5 Quality and inspection requirements (ISO 25239-5 2011) German version EN ISO 25239-5 2011《摩擦搅拌焊 铝 第5部分 质量和检查要求(IS.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 25239-5-2012 Friction stir welding - Aluminium - Part 5 Quality and inspection requirements (ISO 25239-5 2011) German version EN ISO 25239-5 2011《摩擦搅拌焊 铝 第5部分 质量和检查要求(IS.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、March 2012 Translation by DIN-Sprachendienst.English price group 11No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS

2、25.160.10!$zax“1876285www.din.deDDIN EN ISO 25239-5Friction stir welding Aluminium Part 5: Quality and inspection requirements (ISO 25239-5:2011)English translation of DIN EN ISO 25239-5:2012-03Rhrreibschweien Aluminium Teil 5: Qualitts- und Prfungsanforderungen (ISO 25239-5:2011)Englische bersetzun

3、g von DIN EN ISO 25239-5:2012-03Soudage par friction-malaxage Aluminium Partie 5: Exigences de qualit et de contrle (ISO 25239-5:2011)Traduction anglaise de DIN EN ISO 25239-5:2012-03www.beuth.deDocument comprises 17 pagesIn case of doubt, the German-language original shall be considered authoritati

4、ve.02.12 DIN EN ISO 25239-5:2012-03 2 A comma is used as the decimal marker. National foreword This standard has been prepared by the Internationaler Verband fr Schweitechnik (IIW) (International Institute of Welding). The responsible German body involved in its preparation was the Normenausschuss S

5、chweien und verwandte Verfahren (NAS) (Welding and allied processes Standards Committee), DIN/DVS Joint Committee NA 092-00-27 AA Rhrreibschweien (DVS AG V 11.2). Requests for official interpretations of any aspect of this International Standard should be addressed to the ISO Central Secretariat, wh

6、ich will pass them on to the IIW Secretariat for an official response. DIN EN ISO 25239 consists of the following parts, under the general title Friction stir welding Aluminium: Part 1: Vocabulary Part 2: Design of weld joints Part 3: Qualification of welding operators Part 4: Specification and qual

7、ification of welding procedures Part 5: Quality and inspection requirements The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 3452-1 DIN EN 571-1 ISO 3834-2 DIN EN ISO 3834-2 ISO 4136 DIN EN ISO 4136 ISO 5173 DIN EN ISO 5173 ISO 9015-1 DI

8、N EN ISO 9015-1 ISO 9015-2 DIN EN ISO 9015-2 ISO 9017 DIN EN 1320 ISO 9712 DIN EN ISO 9712 ISO 17636 (all parts) E DIN EN ISO 17636 (all parts) ISO 17637 DIN EN ISO 17637 ISO 17640 DIN EN ISO 17640 ISO 25239-1 DIN EN ISO 25239-1 ISO 25239-3 DIN EN ISO 25239-3 ISO 25239-4:2011 DIN EN ISO 25239-4:2012

9、-03 DIN EN ISO 25239-5:2012-03 3 National Annex NA (informative) Bibliography DIN EN 571-1, Non-destructive testing Penetrant testing Part 1: General principles DIN EN 1320, Destructive tests on welds in metallic materials Fracture test DIN EN ISO 3834-2, Quality requirements for fusion welding of m

10、etallic materials Part 2: Comprehensive quality requirements DIN EN ISO 4136, Destructive tests on welds in metallic materials Transverse tensile test DIN EN ISO 5173, Destructive tests on welds in metallic materials Bend tests DIN EN ISO 9015-1, Destructive tests on welds in metallic materials Hard

11、ness testing Part 1: Hardness test on arc welded joints DIN EN ISO 9015-2, Destructive tests on welds in metallic materials Hardness testing Part 2: Microhardness testing of welded joints DIN EN ISO 9712, Non destructive testing Qualification and certification of NDT personnel General principles E D

12、IN EN ISO 17636-1, Non-destructive testing of welds Radiographic testing Part 1: X- and gamma ray techniques with film E DIN EN ISO 17636-2, Non-destructive testing of welds Radiographic testing Part 2: X- and gamma ray techniques with digital detectors DIN EN ISO 17637, Non-destructive testing of w

13、elds Visual testing of fusion-welded joints DIN EN ISO 17640, Non-destructive testing of welds Ultrasonic testing Techniques, testing levels, and assessment DIN EN ISO 25239-1, Friction stir welding Aluminium Part 1: Vocabulary DIN EN ISO 25239-3, Friction stir welding Aluminium Part 3: Qualificatio

14、n of welding operators DIN EN ISO 25239-4:2012-03, Friction stir welding Aluminium Part 4: Specification and qualification of welding procedures DIN EN ISO 25239-5:2012-03 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 25239-5 December 2011 ICS 25.160.10

15、English Version Friction stir welding - Aluminium - Part 5: Quality and inspection requirements (ISO 25239-5:2011) Soudage par friction-malaxage - Aluminium - Partie 5: Exigences de qualit et de contrle (ISO 25239-5:2011) Rhrreibschweien - Aluminium - Teil 5: Qualitts- und Prfungsanforderungen (ISO

16、25239-5:2011) This European Standard was approved by CEN on 4 June 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliogra

17、phical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibil

18、ity of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,

19、Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management C

20、entre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 25239-5:2011: EContents Page Foreword .3 Introduction . 4 1 Scope 5 2 Normative references 5 3 Terms and definitions . 6 4 Quality re

21、quirements . 6 4.1 General . 6 4.2 Welding personnel 6 4.3 Inspection and testing personnel 6 4.4 Equipment 6 4.5 Welding procedure specification . 7 4.6 Friction stir welding tool . 8 4.7 Preweld joint preparation and fit-up 8 4.8 Preheating and interpass temperature control 8 4.9 Tack welds . 8 4.

22、10 Welding . 8 4.11 Postweld heat treatment . 8 4.12 Inspection and testing 8 4.13 Identification and traceability 10 Annex A (normative) Imperfections, testing and examination, acceptance levels, and ISO 6520-1 reference number . 11 Bibliography . 13 EN ISO 25239-5:2011 (E) DIN EN ISO 25239-5:2012-

23、03 2Foreword This document (EN ISO 25239-5:2011) has been prepared by the International Institute of Welding in collaboration with Technical Committee CEN/TC 121 “Welding” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publ

24、ication of an identical text or by endorsement, at the latest by June 2012, and conflicting national standards shall be withdrawn at the latest by June 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall

25、 not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denma

26、rk, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 25239-5:2011 has been appro

27、ved by CEN as a EN ISO 25239-5:2011 without any modification. EN ISO 25239-5:2011 (E) DIN EN ISO 25239-5:2012-03 3 Introduction Welding processes are widely used in the fabrication of engineered structures. During the second half of the twentieth century, fusion welding processes, wherein fusion is

28、obtained by the melting of parent material and usually a filler metal, dominated the welding of large structures. Then, in 1991, Wayne Thomas at TWI invented friction stir welding (FSW), which is carried out entirely in the solid phase (no melting). The increasing use of FSW has created the need for

29、 this International Standard in order to ensure that welding is carried out in the most effective way and that appropriate control is exercised over all aspects of the operation. This International Standard focuses on the FSW of aluminium because, at the time of publication, the majority of commerci

30、al applications for FSW involved aluminium. Examples include railway carriages, consumer products, food processing equipment, aerospace structures, and marine vessels. The parts of this International Standard are listed in the foreword. Part 1 defines terms specific to FSW. Part 2 specifies design r

31、equirements for friction stir weld joints in aluminium. Part 3 specifies requirements for the qualification of an operator for the FSW of aluminium. Part 4 specifies requirements for the specification and qualification of welding procedures for the FSW of aluminium. A welding procedure specification

32、 (WPS) is needed to provide a basis for planning welding operations and for quality control during welding. Welding is considered a special process in the terminology of standards for quality systems. Standards for quality systems usually require that special processes be carried out in accordance w

33、ith written procedure specifications. Metallurgical deviations constitute a special problem. Because non-destructive testing of the mechanical properties is impossible at the present level of technology, this has resulted in the establishment of a set of rules for qualification of the welding proced

34、ure prior to the release of the WPS to actual production. ISO 25239-4 defines these rules. Part 5 specifies a method for determining the capability of a manufacturer to use the FSW process for the production of aluminium products of the specified quality. It defines specific quality requirements but

35、 does not assign those requirements to any specific product group. To be effective, welded structures should be free from serious problems in production and in service. To achieve that goal, it is necessary to provide controls from the design phase through material selection, fabrication, and inspec

36、tion. For example, poor design can create serious and costly difficulties in the workshop, on site, or in service. Incorrect material selection can result in welding problems, such as cracking. Welding procedures have to be correctly formulated and qualified to avoid imperfections. To ensure the fab

37、rication of a quality product, management should understand the sources of potential trouble and introduce appropriate quality and inspection procedures. Supervision should be implemented to ensure that the specified quality is achieved. EN ISO 25239-5:2011 (E) DIN EN ISO 25239-5:2012-03 41 Scope Th

38、is part of ISO 25239 specifies a method for determining the capability of a manufacturer to use the friction stir welding (FSW) process for the production of products of the specified quality. It specifies quality requirements, but does not assign those requirements to any specific product group. In

39、 this part of ISO 25239, the term “aluminium” refers to aluminium and its alloys. This part of ISO 25239 does not apply to friction stir spot welding. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edit

40、ion cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3452-1, Non-destructive testing Penetrant testing Part 1: General principles ISO 4136, Destructive tests on welds in metallic materials Transverse tensile test ISO 5173, D

41、estructive tests on welds in metallic materials Bend tests ISO 9015-1, Destructive tests on welds in metallic materials Hardness testing Part 1: Hardness test on arc welded joints ISO 9015-2, Destructive tests on welds in metallic materials Hardness testing Part 2: Microhardness testing of welded jo

42、ints ISO 9017, Destructive tests on welds in metallic materials Fracture test ISO 9712, Non-destructive testing Qualification and certification of NDT personnel General principles ISO 17636 (all parts), Non-destructive testing of welds Radiographic testing1)ISO 17637, Non-destructive testing of weld

43、s Visual testing of fusion-welded joints ISO 17640, Non-destructive testing of welds Ultrasonic testing Techniques, testing levels, and assessment ISO 20807, Non-destructive testing Qualification of personnel for limited application of non-destructive testing ISO 25239-1, Friction stir welding Alumi

44、nium Part 1: Vocabulary 1) To be published. (Revision of ISO 17636:2003) EN ISO 25239-5:2011 (E) DIN EN ISO 25239-5:2012-03 5 ISO 25239-3, Friction stir welding Aluminium Part 3: Qualification of welding operators ISO 25239-4:2011, Friction stir welding Aluminium Part 4: Specification and qualificat

45、ion of welding procedures 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 25239-1 apply. 4 Quality requirements 4.1 General These requirements relate only to those aspects of product quality that may be influenced by FSW. 4.2 Welding personnel 4.2.1

46、General Manufacturers shall have at their disposal sufficient competent personnel for the planning, performance and supervision of FSW production operations in accordance with specified requirements. 4.2.2 Welding operator Welding operators shall be qualified in accordance with ISO 25239-3. Qualific

47、ation records shall be kept up to date. 4.3 Inspection and testing personnel 4.3.1 General Manufacturers shall have sufficient competent personnel for the planning, performance, and supervision of inspection and testing operations during the production of friction stir welded parts in accordance with specified requirements. 4.3.2 Personnel performing non-destructive testing and visual testing Non-destructive and visual testing personnel shall be qualified in accordance with ISO 9712 or ISO 20807. When the use of an examination method not currently incorpo