DIN EN ISO 8130-3-2011 Coating powders - Part 3 Determination of density by liquid displacement pyknometer (ISO 8130-3 1992) German version EN ISO 8130-3 2010《粉末涂料 第3部分 用液体置换比重计法测定.pdf

《DIN EN ISO 8130-3-2011 Coating powders - Part 3 Determination of density by liquid displacement pyknometer (ISO 8130-3 1992) German version EN ISO 8130-3 2010《粉末涂料 第3部分 用液体置换比重计法测定.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 8130-3-2011 Coating powders - Part 3 Determination of density by liquid displacement pyknometer (ISO 8130-3 1992) German version EN ISO 8130-3 2010《粉末涂料 第3部分 用液体置换比重计法测定.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、February 2011 Translation by DIN-Sprachendienst.English price group 7No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC

2、S 87.040!$m%“1745702www.din.deDDIN EN ISO 8130-3Coating powders Part 3: Determination of density by liquid displacement pyknometer(ISO 8130-3:1992)English translation of DIN EN ISO 8130-3:2011-02Pulverlacke Teil 3: Bestimmung der Dichte mit einem Pyknometer durch Flssigkeitsverdrngung(ISO 8130-3:199

3、2)Englische bersetzung von DIN EN ISO 8130-3:2011-02Poudres pour revtement Partie 3: Dtermination de la masse volumique laide dun pycnomtre dplacement de liquide (ISO 8130-3:1992)Traduction anglaise de DIN EN ISO 8130-3:2011-02SupersedesDIN ISO 8130-3:2005-04www.beuth.deDocument comprises pagesIn ca

4、se of doubt, the German-language original shall be considered authoritative.1002.11 DIN EN ISO 8130-3:2011-02 2 A comma is used as the decimal marker. National foreword This standard has been prepared by Technical Committee ISO/TC 35 “Paints and varnishes”, Subcommittee SC 9 “General test methods fo

5、r paints and varnishes” (Secretariat: BSI, United Kingdom) in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Beschichtungsstoffe und Beschichtungen (Coatings and Coa

6、ting Materials Standards Committee), Working Committee NA 002-00-07 AA Allgemeine Prfverfahren fr Beschichtungsstoffe und Beschichtungen. DIN EN ISO 8130 consists of the following parts, under the general title Coating powders: Part 1: Determination of particle size distribution by sieving Part 2: D

7、etermination of density by gas comparison pyknometer (referee method) Part 3: Determination of density by liquid displacement pyknometer Part 4: Calculation of lower explosion limit Part 5: Determination of flow properties of a powder/air mixture Part 6: Determination of gel time of thermosetting co

8、ating powders at a given temperature Part 7: Determination of loss of mass on stoving Part 8: Assessment of the storage stability of thermosetting powders Part 9: Sampling Part 10: Determination of deposition efficiency Part 11: Inclined-plane flow test Part 12: Determination of compatibility Part 1

9、3: Particle size analysis by laser diffraction Part 14: Terminology The DIN Standard corresponding to the International Standards referred to in this document are as follows: ISO 787-10 DIN EN ISO 787-10 ISO 842 DIN EN ISO 15528 ISO 3696 DIN ISO 3696 ISO 8130-2 DIN EN ISO 8130-2 Amendments This stan

10、dard differs from DIN ISO 8130-3:2005-04 as follows: a) the status of the standard has been changed to that of a European Standard. sDIN EN ISO 8130-3:2011-02 3 Previous editions DIN 55990-3: 1979-12 DIN ISO 8130-3: 2005-04 National Annex NA (informative) Bibliography DIN EN ISO 787-10, General meth

11、ods of test for pigments and extenders Part 10: Determination of density DIN EN ISO 8130-2, Coating powders Part 2: Determination of density by gas comparison pyknometer (referee method) DIN EN ISO 15528, Paints, varnishes and raw materials for paints and varnishes Sampling DIN ISO 3696, Water for a

12、nalytical laboratory use Specification and test methods Pyknometer method DIN EN ISO 8130-3:2011-02 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 8130-3 November 2010 ICS 87.040 English Version Coating powders - Part 3: Determination of density by liquid

13、 displacement pyknometer (ISO 8130-3:1992) Poudres pour revtement - Partie 3: Dtermination de la masse volumique laide dun pycnomtre dplacement de liquide (ISO 8130-3:1992) Pulverlacke - Teil 3: Bestimmung der Dichte mit einem Pyknometer durch Flssigkeitsverdrngung (ISO 8130-3:1992) This European St

14、andard was approved by CEN on 16 October 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerni

15、ng such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own l

16、anguage and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,

17、Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2

18、010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 8130-3:2010: EEN ISO 8130-3:2010 (E) Contents DIN EN ISO 8130-3:2011-02 2 Page Foreword3 1 Scope 4 2 Normative reference 4 3 Principle4 4 Materials .4 5 Apparatus . 6 Sampling

19、.5 7 Procedure .5 7.1 Determination of the density of the displacement liquid 5 7.2 Determination of the density of the coating powder5 8 Expression of results 5 8.1 Calculation5 8.2 Precision.5 9 Test report 5 5Foreword The text of ISO 8130-3:1992 has been prepared by Technical Committee ISO/TC 35

20、“Paints and varnishes” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 8130-3:2010 by Technical Committee CEN/TC 139 “Paints and varnishes” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard,

21、either by publication of an identical text or by endorsement, at the latest by May 2011, and conflicting national standards shall be withdrawn at the latest by May 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or C

22、ENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Rep

23、ublic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 8130-3:1992 has been approved by CEN as a EN ISO 8130-3:2010 without any modification. EN ISO 8130-3:2010 (E) DIN EN ISO 8130-3:2011-02 3 EN ISO 8130-3:2010 (E) DIN EN ISO 8130-3:2011-02 4 EN ISO 8130-3:2010 (E) DIN EN ISO 8130-3:2011-02 5 EN ISO 8130-3:2010 (E) DIN EN ISO 8130-3:2011-02 6