DIN EN ISO 19062-1-2016 Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 1 Designation system and basis for specifications (ISO 19062-1 2015.pdf

《DIN EN ISO 19062-1-2016 Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 1 Designation system and basis for specifications (ISO 19062-1 2015.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 19062-1-2016 Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 1 Designation system and basis for specifications (ISO 19062-1 2015.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、May 2016 English price group 10No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 83.080.20!%UVd“2505165www.din.deDIN

2、EN ISO 19062-1Plastics Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials Part 1: Designation system and basis for specifications (ISO 19062-1:2015);English version EN ISO 19062-1:2015,English translation of DIN EN ISO 19062-1:2016-05Kunststoffe Acrylnitril-Butadien-Styrol (ABS)-

3、Formmassen Teil 1: Bezeichnungssystem und Basis fr Spezifikationen (ISO 19062-1:2015);Englische Fassung EN ISO 19062-1:2015,Englische bersetzung von DIN EN ISO 19062-1:2016-05Plastiques Acrylonitrile-butadine-styrne (ABS) pour moulage et extrusion Partie 1: Systme de dsignation et base de spcificati

4、ons (ISO 19062-1:2015);Version anglaise EN ISO 19062-1:2015,Traduction anglaise de DIN EN ISO 19062-1:2016-05SupersedesDIN EN ISO 2580-1:2003-02www.beuth.deDocument comprises 15 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.0

5、5.16 DIN EN ISO 19062-1:2016-05 2 A comma is used as the decimal marker. National foreword This document (EN ISO 19062-1:2015) has been prepared by Technical Committee ISO/TC 61 “Plastics” in collaboration with Technical Committee ISO/TC 249 “Plastics” (Secretariat: NBN, Belgium). The responsible Ge

6、rman body involved in its preparation was DIN-Normenausschuss Kunststoffe (DIN Standards Committee Plastics), Working Committee NA 054-02-10 AA Thermoplast-Formmassen. Part 2 of this standard has been published as the following standard: DIN EN ISO 2580-2, Plastics Acrylonitrile-butadiene-styrene (A

7、BS) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 1043-1 DIN EN ISO 1043-1 ISO 1043-2 DIN EN ISO 1043-2 ISO 2580-2 DIN EN ISO 2580-

8、2 Amendments This standard differs from DIN EN ISO 2580-1:2003-02 as follows: a) the number of the standard has been changed; b) the Introduction has been added; c) Clause 2 “Normative references” has been revised; d) the data block system has been revised and brought more into line with ISO 1043 an

9、d ISO 11469. Previous editions DIN 16772-1: 1977-08, 1987-09 DIN EN ISO 2580-1: 1999-10, 2001-07, 2003-02 National Annex NA (informative) Bibliography DIN EN ISO 1043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics DIN EN ISO 1043-2, Plastics Symbol

10、s and abbreviated terms Part 2: Fillers and reinforcing materials DIN EN ISO 2580-2, Plastics Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 19062-1

11、December 2015 ICS 83.080.20 Supersedes EN ISO 2580-1:2002English Version Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 19062-1:2015) Plastiques - Acrylonitrile-butadine-styrne (ABS) pour moulage et ext

12、rusion - Partie 1 : Systme de dsignation et base de spcification(ISO 19062-1:2015) Kunststoffe - Acrylnitril-Butadien-Styrol (ABS)-Formmassen - Teil 1: Bezeichnungssystem und Basis fr Spezifikationen (ISO 19062-1:2015) This European Standard was approved by CEN on 26 September 2015. CEN members are

13、bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to th

14、e CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Cent

15、re has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuani

16、a, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000

17、 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 19062-1:2015 EEuropean foreword .3Introduction 51 Scope . 62 Normative references 73 Designation system 73.1 General . 73.2 Data block 1 . 73.3 Data block 2 . 83.4

18、Data block 3 . 93.5 Data block 4 103.5.1 Vicat softening temperature . 103.5.2 Melt mass-flow rate 113.5.3 Charpy notched impact strength. 113.5.4 Tensile modulus . 113.6 Data block 5 124 Examples of designations . 12Contents PageDIN EN ISO 19062-1:2016-05EN ISO 19062-1:2015 (E)2Foreword 4European f

19、oreword This document (EN ISO 19062-1:2015) has been prepared by Technical Committee ISO/TC 61 “Plastics“ in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by public

20、ation of an identical text or by endorsement, at the latest by June 2016, and conflicting national standards shall be withdrawn at the latest by June 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall n

21、ot be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 2580-1:2002. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulga

22、ria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Tur

23、key and the United Kingdom. Endorsement notice The text of ISO 19062-1:2015 has been approved by CEN as EN ISO 19062-1:2015 without any modification. DIN EN ISO 19062-1:2016-05EN ISO 19062-1:2015 (E)3 ForewordISO (the International Organization for Standardization) is a worldwide federation of natio

24、nal standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Internati

25、onal organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended

26、 for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso

27、.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will

28、be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expression

29、s related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplast

30、ic materials.This first edition of ISO 19062-1 cancels and replaces ISO 2580-1:2002, which has been technically revised to introduce a new designation system.The revised designation system is published under a new ISO number, as many existing documents refer to ISO 2580-1. If the existing ISO 2580-1

31、 would be replaced by the new designation system, these documents would refer to the incorrect designation system.In order to give users time to switch from ISO 2580-1 to ISO 19062-1, any designation system according to ISO 2580-1 is to be phased out in 5 to 10 years. During this period, ISO 2580-2

32、will effectively be Part 2 of this International Standard.ISO 19062 consists of the following parts, under the general title Plastics Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials: Part 1: Designation system and basis for specificationsDIN EN ISO 19062-1:2016-05EN ISO 19062-

33、1:2015 (E)4 IntroductionISO 2580-1 is complex and does not fit with daily practice anymore. In practice, ISO 1043 (all parts) and ISO 11469 are, in combination, “improperly” being used as a designation system for, e.g. marking. The aim of this International Standard is to simplify the data block sys

34、tem and to connect more to ISO 1043 (all parts) and ISO 11469, where the first two blocks are used for generic identification and marking of products.DIN EN ISO 19062-1:2016-05EN ISO 19062-1:2015 (E)5 1 ScopeThis part of ISO 19062 establishes a system of designation for acrylonitrile-butadiene-styre

35、ne (ABS) moulding and extrusion materials, which may be used as the basis for specifications.The types of ABS plastic are differentiated from each other by a classification system based on appropriate levels of the designatory properties:a) Vicat softening temperature;b) melt mass-flow rate;c) Charp

36、y notched impact strength;d) tensile modulus;and on information about composition, intended application and/or method of processing, important properties, additives, colorants, fillers, and reinforcing materials.This part of ISO 19062 is applicable to all acrylonitrile-butadiene-styrene materials co

37、nsisting of a continuous phase based mainly on copolymers of styrene (and/or alkyl-substituted styrene) and acrylonitrile and a dispersed elastomeric phase based mainly on polybutadiene, plus other components, in such quantities as specified in the text.It applies to ABS materials ready for normal u

38、se in the form of powder, granules, pellets or chips, unmodified or modified by colorants, additives, fillers, etc.This part of ISO 19062 does not apply to materialsa) with a Charpy notched impact strength of less than three kilojoules per square metre,b) containing less than 50 % by mass of butadie

39、ne in the elastomer of the elastomeric phase, andc) containing less than 15 % by mass of acrylonitrile in the continuous phase.It is not intended to imply that materials having the same designation give necessarily the same performance. This part of ISO 19062 does not provide engineering data, perfo

40、rmance data, or data on processing conditions which may be required to specify a material for a particular application and/or method of processing.If such additional properties are required, they will be determined in accordance with the test methods specified in ISO 2580-2, if suitable.In order to

41、specify a thermoplastic material for a particular application or to ensure reproducible processing, additional requirements may be given in data block 5 (see 3.1).DIN EN ISO 19062-1:2016-05EN ISO 19062-1:2015 (E)6 2 Normative referencesThe following documents, in whole or in part, are normatively re

42、ferenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 1043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymer

43、s and their special characteristicsISO 1043-2, Plastics Symbols and abbreviated terms Part 2: Fillers and reinforcing materialsISO 2580-2, Plastics Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties3 Designatio

44、n system3.1 GeneralThe designation system for thermoplastics is based on the following standardized pattern:DesignationDescription block (optional)Identity blockInternational Standard number blockIndividual-item blockData block 1Data block 2Data block 3Data block 4Data block 5The designation consist

45、s of an optional description block, reading “Thermoplastics”, and an identity block comprising the International Standard number and an individual-item block. For unambiguous designation, the individual-item block is subdivided into five data blocks comprising the following information: Data block 1

46、: Identification of the plastic by its abbreviated term (ABS) in accordance with ISO 1043-1 and information about the composition of the polymer (see 3.2); Data block 2: Fillers or reinforcing materials and their nominal content (see 3.3); Data block 3: First letter: Intended application and/or meth

47、od of processing (see 3.4);Letters 2 to 8: Important properties, additives, and supplementary information (see 3.4); Data block 4: Designatory properties (see 3.5); Data block 5: For the purpose of specifications, a fifth data block may be added containing addi-tional information (see 3.6).The first

48、 character of the individual-item block shall be a hyphen. The data blocks shall be separated from each other by commas.If a data block is not used, this shall be indicated by doubling the separation sign, i.e. by two commas (,).3.2 Data block 1In this data block, after the hyphen, acrylonitrile-butadiene-styrene plastics are identified by its abbreviated term, ABS, in accordance with ISO 1043-1 and after the hyphen, a sin