DIN EN ISO 15995-2010 Gas cylinders - Specifications and testing of LPG cylinder valves - Manually operated (ISO 15995 2006) German version EN ISO 15995 2010《气瓶 液化石油气气瓶阀的试验和规范 手动操作.pdf

《DIN EN ISO 15995-2010 Gas cylinders - Specifications and testing of LPG cylinder valves - Manually operated (ISO 15995 2006) German version EN ISO 15995 2010《气瓶 液化石油气气瓶阀的试验和规范 手动操作.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 15995-2010 Gas cylinders - Specifications and testing of LPG cylinder valves - Manually operated (ISO 15995 2006) German version EN ISO 15995 2010《气瓶 液化石油气气瓶阀的试验和规范 手动操作.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、November 2010 Translation by DIN-Sprachendienst.English price group 14No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).I

2、CS 23.060.20!$l1S“1731448www.din.deDDIN EN ISO 15995Gas cylinders Specifications and testing of LPG cylinder valves Manually operated (ISO 15995:2006)English translation of DIN EN ISO 15995:2010-11Gasflaschen Spezifikation und Prfung von Flaschenventilen fr Flssiggas (LPG) Handbettigt (ISO 15995:200

3、6)Englische bersetzung von DIN EN ISO 15995:2010-11Bouteilles gaz Spcifications et essais pour valves de bouteilles de GPL Fermeture manuelle (ISO 15995:2006)Traduction anglaise de DIN EN ISO 15995:2010-11SupersedesDIN EN 13153:2003-09www.beuth.deDocument comprises pagesIn case of doubt, the German-

4、language original shall be considered authoritative.3011.10 DIN EN ISO 15995:2010-11 2 A comma is used as the decimal marker. National foreword This standard has been prepared by Technical Committee ISO/TC 58 “Gas cylinders” and has been taken over by Technical Committee CEN/TC 286 “Liquefied petrol

5、eum gas equipment and accessories” (Secretariat: NSAI, Ireland). The responsible German body involved in its preparation was the Normenausschuss Druckgasanlagen (Pressurized Gas Installations Standards Committee), Working Committee NA 016-00-06 AA Flssiggas-Gerte und Ausrstung; Spiegelausschuss zu C

6、EN/TC 286. A minor discrepancy in ISO 15995:2006 was not discovered until CEN decided to adopted that standard unchanged. In 5.3.1, Table 1, the test temperature for test no. 16 is given as 65 (/2,5) C, while in 5.19 this temperature is given as 65 C, without a tolerance. The above-mentioned tempera

7、ture with the tolerance is to be taken. The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 11114-1 DIN EN ISO 11114-1 ISO 11114-2 DIN EN ISO 11114-2 ISO 11116-1 DIN EN ISO 11116-1 ISO 10920 and ISO 11116-1 have been replaced by ISO 11363-1

8、 which has been taken over as DIN EN ISO 11363-1. Amendments This standard differs from DIN EN 13153:2003-09 as follows: a) the standard has been brought in line with the current rules of presentation; b) normative references have been updated; c) terms and definitions have been expanded and given i

9、n more detail. Previous editions DIN EN 13153: 2002-03, 2003-09 DIN EN ISO 15995:2010-11 3 National Annex NA (informative) Bibliography DIN EN ISO 11114-1, Transportable gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials DIN EN ISO 11114-2, Trans

10、portable gas cylinders Compatibility of cylinder and valve materials with gas contents Part 2: Non-metallic materials DIN EN ISO 11116-1, Transportable gas cylinders Gas cylinders; 17E taper thread for connection of valves to gas cylinders Part 1: Specification DIN EN ISO 11363-1, Gas cylinders 17E

11、and 25E taper threads for connection of valves to gas cylinders Part 1: Specification DIN EN ISO 15995:2010-11 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 15995 June 2010 ICS 23.020.30 Supersedes EN 13153:2001English Version Gas cylinders - Specificati

12、ons and testing of LPG cylinder valves - Manually operated (ISO 15995:2006) Bouteilles gaz - Spcifications et essais pour valves de bouteilles de GPL - Fermeture manuelle (ISO 15995:2006)Gasflaschen - Spezifikation und Prfung von Flaschenventilen fr Flssiggas (LPG) - Handbettigt (ISO 15995:2006) Thi

13、s European Standard was approved by CEN on 20 May 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

14、 concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into

15、its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,

16、 Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 B

17、russels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 15995:2010: EContents DIN EN ISO 15995:2010-11 EN ISO 15995:2010 (E) 2 Page Foreword3 Introduction .4 1 Scope 5 2 Normative references 5 3 Terms and definitions .5 4

18、Design and specification 8 4.1 General8 4.2 Materials .8 4.3 Essential components.9 4.4 Optional components10 4.5 Leak tightness11 4.6 Operating torque11 4.7 Opening torque 12 4.8 Closing torque12 5 Valve type test12 5.1 General12 5.2 Test procedure and test requirements 12 5.3 External and internal

19、 tightness tests (Test nos. 2, 5, 8, 11, 12, 13, 15, 16 and 17)12 5.4 Hydraulic pressure test (Test no. 1).14 5.5 External and internal tightness test (Test no. 2) 14 5.6 Valve closure test (Test no. 3)15 5.7 Valve stem test (Test no. 4) 15 5.8 External and internal tightness test (Test no. 5) 15 5.

20、9 Hand wheel fire exposure test (Test no. 6) .16 5.10 Impact test (Test no. 7)16 5.11 External and internal tightness test (Test no. 8) 17 5.12 Resistance to excessive closing torque test (Test no. 9)17 5.13 Resistance to excessive opening torque test (Test no. 10) 17 5.14 External tightness test (T

21、est no. 11)18 5.15 External and internal tightness test (Test no. 12) 18 5.16 External and internal tightness test after ageing (Test no. 13).18 5.17 Endurance test (Test no. 14).18 5.18 External and internal tightness test (Test no. 15) 19 5.19 External and internal tightness test High temperature

22、(Test no. 16).19 5.20 External and internal tightness test Low temperature (Test no. 17)19 5.21 Examination of dismantled valves number 9 to 13 (Test number 18)19 5.22 Acceptance criteria19 6 Documentation/Test report.19 6.1 Documentation.19 6.2 Test report 20 7 Markings .20 Annex A (normative) Valv

23、e dimensions21 Annex B (normative) Valves for cylinders up to and including 7,5 litre water capacity22 Annex C (informative) Production testing and inspection24 Annex D (normative) Special low temperature requirements for valves.25 Bibliography 26 Foreword The text of ISO 15995:2006 has been prepare

24、d by Technical Committee ISO/TC 58 “Gas cylinders” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 15995:2010 by Technical Committee CEN/TC 286 “Liquefied petroleum gas equipment and accessories” the secretariat of which is held by NSAI. This European St

25、andard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2010, and conflicting national standards shall be withdrawn at the latest by December 2010. Attention is drawn to the possibility that some of the elements

26、 of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13153:2001. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following coun

27、tries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slov

28、enia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 15995:2006 has been approved by CEN as a EN ISO 15995:2010 without any modification. DIN EN ISO 15995:2010-11 EN ISO 15995:2010 (E) 3 Introduction This International Standard calls for the use of substances a

29、nd procedures that can be injurious to health if adequate precautions are not taken. It refers only to technical suitability and does not absolve the user from legal obligations relating to health and safety at any stage. It has been assumed in the drafting of this International Standard that execut

30、ion of its provisions is entrusted to appropriately qualified and experienced people. DIN EN ISO 15995:2010-11 EN ISO 15995:2010 (E) 4 1 Scope This International Standard specifies the requirements for design, specification and type testing of dedicated LPG manually operated cylinder valves specific

31、ally for use with transportable refillable LPG cylinders from 0,5 l up to 150 l water capacity. It includes references to associated equipment for vapour or liquid service. NOTE Annex C gives the recommendations for production testing and inspection. This International Standard does not apply to fix

32、ed automotive installations. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applie

33、s. ISO 10920, Gas cylinders 25E taper thread for connection of valves to gas cylinders Specification ISO 11114-1, Transportable gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials ISO 11114-2, Transportable gas cylinders Compatibility of cylinder

34、and valve materials with gas contents Part 2: Non-metallic materials ISO 11116-1, Gas cylinders 17E taper thread for connection of valves to gas cylinders Part 1: Specifications 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 liquefied petrol

35、eum gas LPG mixture of predominantly butane or propane with traces of other hydrocarbon gases classified in accordance with UN number 1965, hydrocarbon gas mixture, liquefied, or NOS or UN number 1075, petroleum gases, liquefied NOTE In some countries, UN number 1011 and UN number 1978 may also be u

36、sed to designate LPG. 3.2 cylinder valve valve designed for use in one or more of the following applications: liquid filling, liquid service, vapour service or liquid level indication DIN EN ISO 15995:2010-11 EN ISO 15995:2010 (E) 5 3.3 external tightness resistance to leakage through the valve body

37、 to or from the atmosphere, when the valve is open 3.4 internal tightness resistance to leakage across the valve seat, or other internal sealing components when the valve is closed 3.5 eduction tube tube fitted to the valve to allow withdrawal of liquid LPG with the cylinder in its normal operating

38、position 3.6 fixed liquid level gauge control device, such as a dip tube in combination with a vent valve to verify that the predetermined maximum liquid level in a cylinder has been reached or surpassed 3.7 liquid level indicator control device, such as a float gauge, permitting the gauging of the

39、liquid level in the cylinder 3.8 valve body major valve component including valve stem and/or valve outlet and, where applicable, the provision for other optional components 3.9 excess flow device (flow limiter) device designed to close or partially close when the flow of liquid or vapour passing th

40、rough it exceeds a predetermined value and to re-open when the pressure differential across the valve has been restored below a certain value 3.10 non-return valve valve designed to close automatically to restrict reverse flow 3.11 vapour/liquid dual valve valve designed to allow vapour and liquid w

41、ithdrawal from a cylinder in its normal operating position 3.12 sealing element element used to obtain internal leak tightness 3.13 valve stem section of the valve body, which connects to the cylinder 3.14 valve outlet section of the valve body to which a regulator or connector can be fitted for vap

42、our or liquid withdrawal NOTE The valve outlet is also normally used for filling the cylinder. 3.15 type test test or series of tests conducted to prove that the design meets the requirements of this International Standard DIN EN ISO 15995:2010-11 EN ISO 15995:2010 (E) 6 3.16 cylinder opening part o

43、f the cylinder to which the valve stem connects 3.17 test pressure pressure at which the valve or component is tested in bar gauge 3.18 sediment tube device designed to reduce the risk of foreign matter, which can be in the cylinder, entering the valve 3.19 sealing cap device fitted to, or integral

44、with, the outlet of the cylinder valve to provide secondary closure 3.20 valve operating mechanism mechanism which closes and opens the valve orifice, e.g. threaded valve spindle which, when rotated, raises and lowers a seal 3.21 sealing mechanism mechanism to obtain internal leak tightness 3.22 ope

45、rating torque torque during opening or closing the valve, after the first half rotation of the hand wheel in opening the valve and before the last half rotation of the hand wheel in closing the valve 3.23 opening torque initial torque required to open the valve from the closed position 3.24 closing

46、torque torque required to close the valve and obtain internal tightness 3.25 protection cap device that may be screwed to a fitting permanently attached to the cylinder to protect a cylinder valve 3.26 shroud/guard device that may be welded to the cylinder to protect a cylinder valve 3.27 gross mass

47、 mass of the heaviest cylinder on which the valve is intended to be fitted, including any permanently attached accessories and the maximum mass of the LPG content 3.28 pressure relief valve valve which automatically, without the assistance of any energy other than that of the fluid concerned, discha

48、rges a quantity of fluid so as to prevent a predetermined safe pressure being exceeded, and which is designed to re-close and prevent the further flow of fluid after normal pressure conditions of service have been restored NOTE The loading due to the fluid pressure underneath the valve-sealing element is opposed by a spring. DIN EN ISO 15995:2010-11 EN ISO 15995:2010 (E) 7 4 Design and specification 4.1 General 4.1.1 The valve shall be capable of withstanding: operating pressures and test pres