DIN EN 16617-2015 Pipework - Corrugated metal hose assemblies for combustible gas - Performance requirements testing and marking German version EN 16617 2015《管道工程 可燃气体用波纹状金属软管总成 性能.pdf

《DIN EN 16617-2015 Pipework - Corrugated metal hose assemblies for combustible gas - Performance requirements testing and marking German version EN 16617 2015《管道工程 可燃气体用波纹状金属软管总成 性能.pdf》由会员分享，可在线阅读，更多相关《DIN EN 16617-2015 Pipework - Corrugated metal hose assemblies for combustible gas - Performance requirements testing and marking German version EN 16617 2015《管道工程 可燃气体用波纹状金属软管总成 性能.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、July 2015 Translation by DIN-Sprachendienst.English price group 12No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 2

2、3.040.70!%Co“2327658www.din.deDDIN EN 16617Pipework Corrugated metal hose assemblies for combustible gas Performance requirements, testing and marking;English version EN 16617:2015,English translation of DIN EN 16617:2015-07Rohrleitungen Gewellte Metallschlauchleitungen fr brennbare Gase Leistungsan

3、forderungen, Prfung und Kennzeichnung;Englische Fassung EN 16617:2015,Englische bersetzung von DIN EN 16617:2015-07Tuyauterie Tuyaux flexibles mtalliques onduleux pour les gaz combustibles Exigences des performances, essais et marquage;Version anglaise EN 16617:2015,Traduction anglaise de DIN EN 166

4、17:2015-07www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 22 pages 06.15 DIN EN 16617:2015-07 2 A comma is used as the decimal marker. National foreword This document (EN 16617:2015) has been prepared by Technical Committee CEN/TC 342 “

5、Metal hoses, hose assemblies, bellows and expansion joints” (Secretariat: SNV, Switzerland). The responsible German body involved in its preparation was the DIN-Normenausschuss Rohrleitungen und Dampfkesselanlagen (DIN Standards Committee Piping and Boiler Plant), Working Committee NA 082-00-01 AA S

6、chlauchleitungen und Kompensatoren aus Metall. EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16617 April 2015 ICS 23.040.70 English Version Pipework - Corrugated metal hose assemblies for combustible gas - Performance requirements, testing and marking Tuyauterie - Tuyaux flexibles mtalliques

7、onduleux pour les gaz combustibles - Exigences de performances, essais et marquage Rohrleitungen - Gewellte Metallschlauchleitungen fr brennbare Gase - Leistungsanforderungen, Prfung und Kennzeichnung This European Standard was approved by CEN on 5 March 2015. CEN members are bound to comply with th

8、e CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Managemen

9、t Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status

10、as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, N

11、etherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All

12、 rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16617:2015 EEN 16617:2015 (E) 2 Contents Page Foreword 4 1 Scope 5 2 Normative references 5 3 Terms and definitions .6 4 Design requirements .7 4.1 General 7 4.2 Nominal size (DN) 8 4.2.1 Ge

13、neral 8 4.2.2 Overall length (lO) .8 4.3 Materials .8 4.3.1 General 8 4.3.2 Metal hose, braid, end fittings and ferrules 8 4.3.3 Braid . 10 4.3.4 Gaskets 10 4.4 Attachment of end fittings to the corrugated metal hose assembly for gas with or without braid . 10 4.5 External protection . 10 4.6 End fi

14、ttings 11 4.7 Electrical conductivity 11 4.8 Hose joining 11 4.9 Flow velocity . 11 4.10 Cleanliness 11 5 Performance requirements and tests . 11 5.1 General . 11 5.2 Pressure resistance 12 5.2.1 Requirements 12 5.2.2 Test . 12 5.3 Leak-tightness . 12 5.3.1 Requirement 12 5.3.2 Test . 12 5.4 High te

15、mperature resistance . 12 5.4.1 General . 12 5.4.2 Requirements 12 5.4.3 High temperature test . 12 5.5 Elongation . 13 5.5.1 Requirement 13 5.5.2 Test . 13 5.6 Impact test . 13 5.6.1 Requirement 13 5.6.2 Test . 13 5.7 Burst pressure test . 15 5.7.1 Requirement 15 5.7.2 Test . 15 5.8 Pliability and

16、fatigue . 15 5.9 Electrical conductivity 15 6 Self-assessment report 15 7 Installation instruction . 15 DIN EN 16617:2015-07 EN 16617:2015 (E) 3 8 Designation 16 9 Marking . 16 9.1 Permanent marking . 16 9.2 Marking on label 17 10 Packaging . 17 Annex A (normative) Correspondence between the perform

17、ance tests described by EN ISO 10380 and those of this European Standard . 18 Bibliography 19 DIN EN 16617:2015-07 EN 16617:2015 (E) 4 Foreword This document (EN 16617:2015) has been prepared by Technical Committee CEN/TC 342 “Metal hoses, hose assemblies, bellows and expansion joints”, the secretar

18、iat of which is held by SNV. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2015, and conflicting national standards shall be withdrawn at the latest by October 2015. Attention is drawn t

19、o the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following c

20、ountries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

21、 Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 16617:2015-07 EN 16617:2015 (E) 5 1 Scope This European Standard specifies general requirements for material, design, manufacture, testing, marking and documentation of corrugated metal

22、hose assemblies for gas of diameter up to DN 300 for gases of the 2nd and 3rd families according to EN 437. This European Standard applies to: Corrugated metal hose assemblies for gas for the supply of combustible gas and having a maximum operating pressure (MOP) less than or equal to 16 bar. This E

23、uropean Standard does not apply to: corrugated metal hose assemblies for gas for engines including turbines and internal combustion engines as stated by Pressure Equipment Directive 97/23/EC; corrugated metal hose assemblies for the connection of domestic appliances using gaseous fuels according to

24、EN 14800; corrugated metal hose assemblies for gas buried in earth; corrugated metal hose assemblies with nonpermanent detachable end fittings; stainless steel pliable corrugated tubing kits in buildings for gas with an operating pressure up to 0,5 bar (EN 15266). Users of this European Standard sho

25、uld take into account national standards and existing code of practice in the country of destination. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cit

26、ed applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 437, Test gases Test pressures Appliance categories EN 549, Rubber materials for seals and diaphragms for gas appliances and gas equipment EN 682, Elastomeric Seals Materials requ

27、irements for seals used in pipes and fittings carrying gas and hydrocarbon fluids EN 1562, Founding Malleable cast irons EN 1775:2007, Gas supply Gas pipework for buildings Maximum operating pressure less than or equal to 5 bar - Functional recommendations EN 1779, Non-destructive testing Leak testi

28、ng Criteria for method and technique selection EN 10028-7, Flat products made of steels for pressure purposes Part 7: Stainless steels EN 10088-3, Stainless steels Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting

29、steels for general purposes EN 10242, Threaded pipe fitting in malleable cast iron DIN EN 16617:2015-07 EN 16617:2015 (E) 6 EN 12163, Copper and copper alloys Rod for general purposes EN 12166, Copper and copper alloys Wire for general purposes EN 12168, Copper and copper alloys Hollow rod for free

30、machining purposes EN 14800, Corrugated safety metal hose assemblies for the connection of domestic appliances using gaseous fuels EN ISO 6708:1995, Pipework components Definition and selection of DN (nominal size) (ISO 6708:1995) EN ISO 7369:2004, Pipework Metal hoses and hose assemblies Vocabulary

31、 (ISO 7369:2004) EN ISO 10380:2012, Pipework Corrugated metal hoses and hose assemblies (ISO 10380:2012) 3 Terms and definitions For the purpose of this document, the following terms and definitions apply: 3.1 corrugated metal hose pressure-tight hose made from tube or from welded strip with corruga

32、tions, helicoidal or annular to the axis of the hose, made by deforming the metal SOURCE: EN ISO 7369:2004, 3.1.2 3.2 braid tubular woven stocking of metal wires used to provide pressure strength and/or external protection SOURCE: EN ISO 7369:2004, 4.1.9 3.3 end fittings non-detachable part which is

33、 permanently attached to the end of the corrugated metal hose and if relevant to the braid and which ensures a workable connection to the pipe system, so as to ensure that it cannot be detached without destruction or alteration of the corrugated metal gas hose assembly 3.4 corrugated metal gas hose

34、assembly element of flexible pipe-work consisting of a corrugated metal hose, with braid if required, its end fittings with appropriate gaskets if any and, if required, an external protection 3.5 external protection outer cover used to protect the corrugated metal hose assembly against environmental

35、 and other outside influences 3.6 nominal length length, including end fittings of the straightened-out hose assembly, unless otherwise specified SOURCE: EN ISO 7369:2004, 4.2.1 DIN EN 16617:2015-07 EN 16617:2015 (E) 7 3.7 minimum bending radius radius measured to the centre line of the hose axis at

36、 which the corrugated metal gas hose assembly is designed to operate 3.8 gasket component assuring leak-tightness between two adjacent elements 3.9 gas second and third family gas which are commonly referred to as natural gases or liquefied petroleum gases (LPG) SOURCE: EN 437 3.10 maximum operating

37、 pressure MOP maximum pressure for which the corrugated metal gas hose assembly can be operated under working conditions 3.11 DN (for components of a pipework system) alphanumeric designation of size comprising the letters DN followed by a dimensionless whole number that is indirectly related to the

38、 physical size, in millimetres, of the bore, and is used as a reference Note 1 to entry: This defined number does not represent a measurable value and should not be used for calculation purposes except where specified in the relevant standard. SOURCE: EN ISO 6708:1995 and EN ISO 7369:2004, 4.1.5 4 D

39、esign requirements 4.1 General Corrugated metal hose assemblies for gas, braided or unbraided, are designed to allow frequent movement. These design requirements shall ensure that the construction of corrugated metal hose assemblies for gas, when properly installed and correctly used, under normal c

40、hemical, mechanical and thermal conditions will provide long term safe operation without degradation. For temperature above 50 C care shall be taken to apply a derating factors given in EN ISO 10380. Corrugated metal hose assemblies for gas are classified according to EN ISO 10380:2012, 4.1: Type 1-

41、50: corrugated metal hoses of high flexibility with high fatigue life; Type 1-10: corrugated metal hoses of high flexibility with standard fatigue life; Type 2-10: corrugated metal hoses of normal flexibility. Corresponding type test radii for Type 1-50, Type 1-10 and Type 2-10 are given in EN ISO 1

42、0380:2012, Table 8 (including the notes). The performance requirements of the tests described in Annex A (normative) shall apply. DIN EN 16617:2015-07 EN 16617:2015(E)8 4.2 Nominal size (DN) 4.2.1 General The standard nominal sizes designation shall be as given in EN ISO 10380:2012, 4.2. 4.2.2 Overa

43、ll length (lO) The tolerances of EN ISO 10380:2012, 4.3, shall apply. The maximum overall length of the corrugated metal hose assemblies for gas is subject to national requirements if any. 4.3 Materials 4.3.1 General Materials for the manufacture of a corrugated metal hose assembly for gas shall be

44、selected from Table 1 and their related suitability for fabrication, e.g. welding, cold forming, etc, as appropriate and the conditions under which they will be used. 4.3.2 Metal hose, braid, end fittings and ferrules 4.3.2.1 General The materials used for metal hose, braid, end fittings and ferrule

45、s shall be selected from Table 1. DIN EN 16617:2015-07 EN 16617:2015 (E) 9 Table 1 Materials Materials Hose Braid End fittings aand ferrules Corrugated metal hose Stainless steels according to EN 100287 Stainless steels according to EN 100883 Stainless steels according to EN 100883 Steel grade Steel

46、 number Steel grade Steel number Steel grade Steel number X2CrNi 1911 1.4306 X5CrNi 1810 1.4301 X5CrNi 1810 1.4301 X6CrNiTi 1810 1.4541 X2CrNi 1911 1.4306 X2CrNi 1911 1.4306 X2CrNiMo 17122 1.4404 X6CrNiTi 1810 1.4541 X6CrNiTi 1810 1.4541 X2CrNiMo 18143 1.4435 X2CrNiMo 17122 1.4404 X2CrNiMo 17122 1.4

47、404 X5CrNiMo 17122 1.4401 X2CrNiMo 18143 1.4435 X2CrNiMo 18143 1.4435 X6CrNiMoTi 17122 1.4571 X5CrNiMo 17122 1.4401 X5CrNiMo 17122 1.4401 X6CrNiMoTi 17122 1.4571 X6CrNiMoTi 17122 1.4571 Carbon steel containing a maximum of 0,05 % sulfur and 0,05 % phosphorus bCopper alloys according to EN 12163 to E

48、N 12168 except for EN 12166 (copper wire) Copper grade Number CuZn39Pb2 CW612N CuZn39Pb3 CW614N CuZn40Pb2 CW617N Malleable cast iron for threaded end fittings according to EN 10242. Material shall be according to EN 1562. Malleable cast iron parts shall be made weldable by multiple tempering. The carbon content of the welding zones shall not exceed 0,3 %. aThe material specified for end fittings applies only to the parts which are welded or brazed to