DIN EN 840-2-2013 Mobile waste and recycling containers - Part 2 Containers with 4 wheels with a capacity up to 1 300 l with flat lid(s) for trunnion and or comb lifting devices - .pdf

《DIN EN 840-2-2013 Mobile waste and recycling containers - Part 2 Containers with 4 wheels with a capacity up to 1 300 l with flat lid(s) for trunnion and or comb lifting devices - .pdf》由会员分享，可在线阅读，更多相关《DIN EN 840-2-2013 Mobile waste and recycling containers - Part 2 Containers with 4 wheels with a capacity up to 1 300 l with flat lid(s) for trunnion and or comb lifting devices - .pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、March 2013 Translation by DIN-Sprachendienst.English price group 11No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS

2、13.030.40!$r“1957959www.din.deDDIN EN 840-2Mobile waste and recycling containers Part 2: Containers with 4 wheels with a capacity up to 1 300 l with flatlid(s), for trunnion and/or comb lifting devices Dimensions and design;English version EN 840-2:2012,English translation of DIN EN 840-2:2013-03Fah

3、rbare Abfall- und Wertstoffbehlter Teil 2: Behlter mit 4 Rdern und einem Nennvolumen bis 1 300 l mit Flachdeckel(n), frSchttungen mit Zapfenaufnahme und/oder fr Kammschttungen Mae und Formgebung;Englische Fassung EN 840-2:2012,Englische bersetzung von DIN EN 840-2:2013-03Conteneurs roulants ordures

4、mnagres et recyclables Partie 2: Conteneurs 4 roues de capacit infrieure ou gale 1 300 l couvercle(s)bomb(s), pour lve-conteneurs par tourillon et/ou peigne Dimensions et conception;Version anglaise EN 840-2:2012,Traduction anglaise de DIN EN 840-2:2013-03SupersedesDIN EN 840-2:2004-07www.beuth.deDo

5、cument comprises 20 pagesIn case of doubt, the German-language original shall be considered authoritative.02.13 DIN EN 840-2:2013-03 2 A comma is used as the decimal marker. National foreword This document (EN 840-2:2012) has been prepared by Technical Committee CEN/TC 183 “Waste management” (Secret

6、ariat: DIN, Germany), Working Group WG 1 “Waste containers” (lead-management: UNI, Italy). The responsible German body involved in its preparation was the Normenausschuss Kommunale Technik (Municipal Services Standards Committee), Working Committee NA 051-02-01 AA Abfallentsorgung; Umleerbehlter bis

7、 5 m3und Abfallbehlterschrnke (Spiegelgremium fr CEN/TC 183/WG 1). Amendments This standard differs from DIN EN 840-2:2004-07 as follows: a) the German title has been modified; b) the standard has been editorially revised and brought in line with the state of the art; c) frontal receivers Form B and

8、 Form C have been deleted and Figure 2 has been changed accordingly; d) Figure 3 has been deleted. Previous editions DIN EN 840-2: 1997-03, 2004-07 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 840-2 December 2012 ICS 13.030.40 Supersedes EN 840-2:2004English Version Mobile waste and recyclin

9、g containers - Part 2: Containers with 4 wheels with a capacity up to 1 300 l with flat lid(s), for trunnion and/or comb lifting devices - Dimensions and design Conteneurs roulants ordures mnagres et recyclables - Partie 3: Conteneurs 4 roues de capacit infrieure ou gale 1300 l couvercle(s) bomb(s),

10、 pour lve-conteneurs par tourillon et/ou peigne - Dimensions et conception Fahrbare Abfall- und Wertstoffbehlter - Teil 2: Behlter mit 4 Rdern und einem Nennvolumen bis 1300 l mit Flachdeckel(n), fr Schttungen mit Zapfenaufnahme und/oder fr Kammschttungen - Mae und Formgebung This European Standard

11、was approved by CEN on 22 September 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning su

12、ch national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its ow

13、n language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,

14、Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORM

15、UNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 840-2:2012: EEN 840-2:2012 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 Vol

16、umes 55 Dimensions and design 56 Nominal mass .67 Safety and health requirements .68 Testing 69 Marking .610 Designation 7Annex A (informative) Recommendations for manufacturers of lifting devices . 15Annex B (informative) A-Deviations . 17Bibliography . 18DIN EN 840-2:2013-03 EN 840-2:2012 (E) 3 Fo

17、reword This document (EN 840-2:2012) has been prepared by Technical Committee CEN/TC 183 “Waste management”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest b

18、y June 2013, and conflicting national standards shall be withdrawn at the latest by June 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent

19、 rights. This document supersedes EN 840-2:2004. Technical changes since the latest edition: The content was adapted to the current state of the art and revised editorially. Figure 3 has been deleted. Frontal receivers Form B and C have been deleted. Figure 2 has been changed accordingly. This Europ

20、ean Standard is one part of the series of standards of EN 840 with the main title Mobile waste and recycling containers comprising the following parts: Part 1: Containers with 2 wheels with a capacity up to 400 l for comb lifting devices Dimensions and design; Part 2: Containers with 4 wheels with a

21、 capacity up to 1 300 l with flat lid(s), for trunnion and/or comb lifting devices Dimensions and design (the present document); Part 3: Containers with 4 wheels with a capacity up to 1 300 l with dome lid(s), for trunnion and/or comb lifting devices Dimensions and design; Part 4: Containers with 4

22、wheels with a capacity up to 1 700 l with flat lid(s), for wide trunnion or BG- and/or wide comb lifting devices Dimensions and design; Part 5: Performance requirements and test methods; Part 6: Safety and health requirements. According to the CEN/CENELEC Internal Regulations, the national standards

23、 organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxemb

24、ourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 840-2:2013-03 EN 840-2:2012 (E) 4 1 Scope This European Standard specifies dimensions and design requirements of mobile waste containers with 4 wheels, w

25、ith flat lid(s) and capacity up to 1 300 l to be used by trunnion and/or comb lifting device. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited appli

26、es. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 840-5, Mobile waste and recycling containers Part 5: Performance requirements and test methods EN 840-6:2012, Mobile waste and recycling containers Part 6: Safety and health requirements

27、EN 1501-1, Refuse collection vehicles General requirements and safety requirements Part 1: Rear loaded refuse collection vehicles EN 1501-5:2011, Refuse collection vehicles General requirements and safety requirements Part 5: Lifting devices for refuse collection vehicles EN ISO 11469, Plastics Gene

28、ric identification and marking of plastics products (ISO 11469) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. NOTE Terms for components of mobile waste containers and lifting devices in three languages are given in Annex A of EN 840-1:2012. 3.1

29、 mobile waste and recycling container appropriately designed container fitted with wheels intended to temporarily store waste 3.2 lifting device structure which picks-up, tilts and empties containers 3.3 comb lifting device lifting device in which the picking-up system consists of a row of teeth and

30、 a locking system to retain the container during emptying 3.4 trunnion lifting device lifting device in which the picking-up system consists of a pair of arms with automatic locking mechanism to fit the trunnion to retain the container during emptying 3.5 volume total space inside the container when

31、 the lid is closed Note 1 to entry: See Table 1. DIN EN 840-2:2013-03 EN 840-2:2012 (E) 5 3.6 nominal volume capacity volume stated by the manufacturer Note 1 to entry: See Table 1 without tolerances. Note 2 to entry: The English term “capacity“ and the French term “capacit“ are translated in the Ge

32、rman version by the term “Nennvolumen“. 3.7 nominal mass mass, which is calculated as given in Clause 6 3.8 total permissible mass mass of the container plus the nominal mass 3.9 functional and safety dimensions essential dimensions which ensure the functionality and interchangeability of the contai

33、ner with the compatible lifting device and which are necessary for the operators safety and health 4 Volumes This part of EN 840 identifies the two classes of containers: Class I - small size (nominal volume up to 1 000 l); Class II - large size (nominal volume between 1 000 l and 1 300 l). Within t

34、he two above-mentioned classes of containers the following volumes are identified: 500 l, 660 l, 770 l, 1 000 l, 1 100 l and 1 200 l. Nominal volumes different from those referenced can be used by agreement between user and manufacturer. The tolerance of the volumes shall be 5 % maximum measured acc

35、ording to EN 840-5. 5 Dimensions and design 5.1 The design of the containers need not correspond to the drawings given in Figure 1. The functional dimensions given in Table 1 shall be respected. Recommendations for manufacturers of lifting devices are given in Annex A (see also EN 1501-1). 5.2 The c

36、ontainer shall be constructed so that when it is unloaded or loaded with a nominal load (see Clause 6), it fits on an approved compatible lifting device. It shall be automatically locked safely into the lifting device during the lifting operation. If the container is equipped with a comb receiver, i

37、t shall correspond to Figure 2. 5.3 The lid(s) shall cover the opening of the container completely. It shall be opened easily by itself during the emptying cycle it/they shall be made with at least two fixing points and have at least one means of opening. 5.4 Handles fitted in front of the trunnion

38、shall have a measurement over the handles of 10 mm less than the actual measurement in Table 1, dimension N 33. The handles and their location also shall be designed so that they do not damage the operator. 5.5 If the container has ribs in the frontal receiver they shall meet the requirements of Fig

39、ures 2 and 4. DIN EN 840-2:2013-03 EN 840-2:2012 (E) 6 5.6 The container shall have four swivel castors. Each swivel castor shall be capable of withstanding 1/3 of the total permissible mass. Each castor shall meet the requirements of EN 840-5. The container shall have facilities for mounting the ca

40、stor platine according to at least one of the measurements as shown in Figure 5. 5.7 All the surfaces of the container including design features shall be smooth and free of any foreign bodies or flaws. 5.8 The container should have a drain plug. 5.9 When direction locks are fitted they shall be fixe

41、d on at least two castors. 5.10 The container should be fitted with two braked wheels to requirements of EN 840-5. In case of centralised braking and locking system the brake pedal and the lock shall be fixed on a lateral side of the container. The centralised locking shall be able to be unlocked wi

42、th a standard triangular key as shown in Figure 6. The effectiveness of the centralised braking system shall conform to EN 840-5. 6 Nominal mass The container shall be constructed strongly enough to carry a mass of 0,4 kg/dm3 x nominal volume. Containers with a nominal volume of more than 1 100 l sh

43、all be constructed strongly enough to carry a load of 440 kg. 7 Safety and health requirements The container shall meet the safety and health requirements according to EN 840-6. 8 Testing The container shall fulfil the performance requirements and the tests of EN 840-5. 9 Marking 9.1 Each container

44、complying with the requirements of this part of EN 840 shall be durably and readably marked on the body in a visible part with: number of this European Standard (EN 840-2); nominal volume; manufacturers name or trademark; total permissible mass, in kilograms; year and month of manufacturing. 9.2 Add

45、itional marking for quality, recycling, etc. is allowed. Starting five years after the publication of this standard, plastic parts of containers, lids and wheels shall be marked in accordance with EN ISO 11469. The use of recycled materials is allowed, presuming that all requirements of this standar

46、d are complied with. DIN EN 840-2:2013-03 EN 840-2:2012 (E) 7 10 Designation The container complying with the requirements of this European Standard shall be designated as follows: Container EN 840-2 660 A O 264 Description Standard number Nominal volume, in litres Frontal receiver form: A = frontal

47、 receiver 0 = without frontal receiver Lateral receiver: A = trunnions 0 = without lateral receiver Nominal load, in kilograms DIN EN 840-2:2013-03 EN 840-2:2012 (E) 8 Table 1 Dimensions Dimensions in millimetres Dimen-sion N Class I - Small sizes 1 000 l Remarks 500 l 660 l 770 l 1 000 l 1 100 l 1

48、200 l 1a1 370 10 1 370 10 1 370 10 1 370 10 1 370 10 1 370 10 In case of trunnions 2 680 max. 780 max. 800 max. 1 115 max. 1 115 max. 1 115 max. Total width lid(s) closed 3 740 max. 850 max. 870 max. 1 190 max. 1 190 max. 1 190 max. When lid open 4 1 370 max 1 370 max. 1 370 max. 1 470 max. 1 470 ma