DIN EN 1984-2010 Industrial valves - Steel gate valves German version EN 1984 2010《工业阀门 钢制闸阀 德文版本EN 1984-2010》.pdf

《DIN EN 1984-2010 Industrial valves - Steel gate valves German version EN 1984 2010《工业阀门 钢制闸阀 德文版本EN 1984-2010》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 1984-2010 Industrial valves - Steel gate valves German version EN 1984 2010《工业阀门 钢制闸阀 德文版本EN 1984-2010》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、October 2010 Translation by DIN-Sprachendienst.English price group 10No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC

2、S 23.060.30!$kVx“1725185www.din.deDDIN EN 1984Industrial valves Steel gate valvesEnglish translation of DIN EN 1984:2010-10Industriearmaturen Schieber aus StahlEnglische bersetzung von DIN EN 1984:2010-10Robinetterie industrielle Robinets-vannes en acierTraduction anglaise de DIN EN 1984:2010-10Supe

3、rsedesDIN EN 1984:2000-03www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.1610.10 DIN EN 1984:2010-10 2 National foreword This standard has been prepared by Technical Committee CEN/TC 69 “Industrial valves” (Secretariat: AFNOR, Fran

4、ce). The responsible German body involved in its preparation was the Normenausschuss Armaturen (Valves Standards Committee), Working Committee NA 003-01-02 AA Schieber. Amendments This standard differs from DIN EN 1984:2000-03 as follows: a) normative references in Clauses 2, 4, 5 and 8 have been up

5、dated; b) the Bibliography has been deleted; c) in Table ZA.1, Subclauses 4.2.3 and 5.1 have been correlated to PED, Annex I, sections 3.2.2 and 7.4; d) in Table ZA.1, Subclause 4.1 has been correlated to PED, Annex I, section 2.1. Previous editions DIN 3204: 1928-04, 1942xxx-10 DIN 3205: 1928-04, 1

6、931-04 DIN 3206: 1928-04, 1931-04 DIN 3208: 1928-04 DIN 3216: 1942x-10 DIN 3218: 1942-11, 1943x-10 DIN 3225: 1942xx-10 DIN 3226: 1942xx-10 DIN 3229: 1942x-10 DIN 3352-1: 1979-05 DIN 3352-6: 1979-05 DIN 3352-7: 1979-05 DIN 3352-8: 1980-10 DIN 3352-9: 1979-05 DIN 3352-10: 1979-05 DIN EN 1984: 2000-03

7、EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1984 May 2010 ICS 23.060.30 Supersedes EN 1984:2000English Version Industrial valves - Steel gate valves Robinetterie industrielle - Robinets-vannes en acier Industriearmaturen - Schieber aus Stahl This European Standard was approved by CEN on 9 A

8、pril 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be ob

9、tained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Mana

10、gement Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Nether

11、lands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation i

12、n any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1984:2010: EEN 1984:2010 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .54 Requirements .64.1 Design .64.1.1 Materials .64.1.2 Pressure/temperature ratings .64.1.3 Dimensions

13、 .64.1.4 Operation 94.1.5 Auxiliary connections .94.1.6 Permanent joining. 104.2 Functional characteristics . 104.2.1 Shell design strength . 104.2.2 Flow characteristics . 104.2.3 Seat leakage 104.2.4 Permissible manual operating forces . 115 Test procedures 116 Declaration of compliance . 117 Desi

14、gnation . 118 Marking and preparation for storage and transportation . 118.1 Marking 118.2 Preparation for storage and transportation . 12Annex A (informative) Information to be supplied by the customer . 13Annex ZA (informative) Relationship between this European Standard and the Essential Requirem

15、ents of EU Directive 97/23/EC . 14DIN EN 1984:2010-10 EN 1984:2010 (E) 3 Foreword This document (EN 1984:2010) has been prepared by Technical Committee CEN/TC 69 “Industrial valves”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, e

16、ither by publication of an identical text or by endorsement, at the latest by November 2010, and conflicting national standards shall be withdrawn at the latest by November 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN

17、 and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1984:2000. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of

18、EU Directive 97/23/EC. For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document. 1) The normative references were updated in Clauses 2, 4, 5, 8. 2) The Bibliography was deleted; 3) In Table ZA.1, sub-clauses 4.2.3 and 5.1 were correlated to PED Annex I

19、, sections 3.2.2 and 7.4; 4) In Table ZA.1, sub-clause 4.1 was correlated to PED Annex I, section 2.1. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia

20、, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. DIN EN 1984:2010-10 EN 1984:201

21、0 (E) 4 1 Scope This European Standard specifies the requirements for steel gate valves which are wrought, cast or fabricated with end connections flanged, butt welding, socket welding or threaded. This European Standard is applicable to steel gate valves mainly used for industrial and general purpo

22、se applications. However they can be used for other applications provided the requirements of the relevant performance standards are met. The ranges of nominal sizes covered is: DN 8; DN 10; DN 12; DN 15; DN 20; DN 25; DN 32; DN 40; DN 50; DN 65; DN 80; DN 100; DN 125; DN 150; DN 200; DN 250; DN 300

23、; DN 350; DN 400; DN 450; DN 500; DN 600; DN 700; DN 750; DN 800; DN 900; DN 1000. DN 750 is used for Class designated valves only. DN 8 and DN 12 are not used for flanged end connections. Socket welding end valves and threaded end valves are limited to the range DN 8 to DN 65. The range of pressure

24、 designations covered is: a) for flanged valves 1) PN 10; PN 16; PN 25; PN 40; PN 63; PN 100 2) Class 150; Class 300; Class 600 b) for butt welding end valves 1) PN 10, PN 16, PN 25, PN 40, PN 63, PN 100 2) Class 150, Class 300, Class 600 c) for socket welding end valves and threaded end valves 1) P

25、N 10; PN 16; PN 25; PN 40; PN 63; PN 100 2) Class 600; Class 800 NOTE 1 Socket welding end and threaded end valves are not normally manufactured with the pressure designations PN 10, PN 16, PN 25 and PN 40. NOTE 2 Class 800 is an intermediate class designation widely used for socket welding and thre

26、aded end valves. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 19, In

27、dustrial valves Marking of metallic valves EN 287-1, Qualification test of welders Fusion welding Part 1: Steels DIN EN 1984:2010-10 EN 1984:2010 (E) 5 EN 558, Industrial valves Face-to-face and centre-to-face dimensions of metal valves for use in flanged pipe systems PN and Class designated valves

28、EN 736-1:1995, Valves Terminology Part 1: Definition of types of valves EN 736-2:1997, Valves Terminology Part 2: Definition of components of valves EN 736-3:2008, Valves Terminology Part 3: Definition of terms EN 1092-1, Flanges and their joints Circular flanges for pipes, valves, fittings and acce

29、ssories, PN designated Part 1: Steel flanges EN 1418, Welding personnel Approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials EN 1759-1, Flanges and their joints Circular flanges for pipes, valves, fittin

30、gs and accessories, Class designated Part 1: Steel flanges, NPS to 24 EN 10045-1, Metallic materials Charpy impact test Part 1: Test method EN 12266-1, Industrial valves Testing of valves Part 1: Pressure tests, test procedures and acceptance criteria Mandatory requirements EN 12266-2, Industrial va

31、lves Testing of valves Part 2: Tests, test procedures and acceptance criteria Supplementary requirements EN 12516-1, Industrial valves Shell design strength Part 1: Tabulation method for steel valve shells EN 12516-2, Industrial valves Shell design strength Part 2: Calculation method for steel valve

32、 shells EN 12516-3, Valves Shell design strength Part 3: Experimental method EN 12570, Industrial valves Method for sizing the operating element EN 12627, Industrial valves Butt welding ends for steel valves EN 12760, Valves Socket welding ends for steel valves EN 12982, Industrial valves End-to-end

33、 and centre-to-end dimensions for butt welding end valves EN ISO 228-1:2003, Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) EN ISO 5210, Industrial valves Multi-turn valve actuator attachments (ISO 5210:1991) EN IS

34、O 15607, Specification and qualification of welding procedures for metallic materials General rules (ISO 15607:2003) ISO 7-1:1994, Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation ASME B1.20.1-1983, Pipe Threads, General Purpose (Inch) 3

35、 Terms and definitions For the purposes of this document, the definitions of types of valves and components and the terms and definitions given in EN 736-1:1995, EN 736-2:1997 and EN 736-3:2008 apply. DIN EN 1984:2010-10 EN 1984:2010 (E) 6 4 Requirements 4.1 Design 4.1.1 Materials 4.1.1.1 The body,

36、bonnet and cover materials shall be selected from the grades listed in EN 12516-1. 4.1.1.2 All the internal parts in contact with the fluid shall be made of a material whose corrosion resistance to the fluid being carried is at least equal to the body and bonnet material. 4.1.1.3 Trim materials shal

37、l have a chemical composition and mechanical properties which ensure the mechanical integrity of the valve. The trim comprises the following: a) stem; b) obturator seat; c) body seat; d) backseat (for valves DN 50 and above, when fitted). 4.1.1.4 Stems shall be manufactured from forged, drawn or rol

38、led material. They shall have a minimum corrosion resistance equivalent to a 13 % chromium content ferritic steel. 4.1.2 Pressure/temperature ratings 4.1.2.1 The pressure/temperature ratings shall be as specified in EN 12516-1 for the particular body/bonnet material group. 4.1.2.2 The pressure tempe

39、rature ratings applicable to Class 800 socket welding and threaded end valves shall be the Class 600 rating for the applicable material group multiplied by the ratio of 600800. 4.1.2.3 Restrictions of temperature and pressure below those specified in 4.1.2.1 and 4.1.2.2 for example, those imposed by

40、 soft seals, special trims and bellows seal shall be indicated on the valve (see 8.1.2). 4.1.2.4 For temperatures below the lowest temperature shown in the pressure/temperature rating tables in EN 12516-1, the service pressure shall be no greater than the pressure corresponding to the lowest tempera

41、ture in the rating tables. The use of valves at lower temperatures than shown in the rating tables is permitted providing the bending rupture energy of the body, bonnet and cover material measured on three 10 mm x 10 mm specimens in accordance with EN 10045-1 shall be no less than an average of 27J

42、at a temperature no higher than the lowest scheduled operating temperature. 4.1.3 Dimensions 4.1.3.1 Face-to-face and end-to-end dimensions Face-to-face dimensions for PN and Class designated flanged end valves shall be in accordance with EN 558. The end-to-end dimensions of butt welding end valves

43、shall be in accordance with EN 12982. The end-to-end dimensions of threaded and socket welding end valves is the choice of the manufacturer. DIN EN 1984:2010-10 EN 1984:2010 (E) 7 4.1.3.2 Body end 4.1.3.2.1 Flanged ends shall comply with requirements of EN 1092-1 for PN-designated flanges or with EN

44、 1759-1 for Class designated flanges. Flanged ends shall be cast or forged integral with the body except that flanges may be attached by welding in accordance with 4.1.6. A full penetration butt weld shall be used for the attachment of flanges by welding on sizes larger than DN 50. 4.1.3.2.2 Butt we

45、lding end profiles shall be in accordance with EN 12627. 4.1.3.2.3 Socket welding end dimensions shall be in accordance with EN 12760. The minimum thickness of the pressure retaining material shall be in accordance with EN 12516-1 and EN 12516-2. 4.1.3.2.4 Threaded ends shall be of the internal form

46、 in accordance with Type Rc and Rp to ISO 7-1:1994 or Type G to EN ISO 228-1:2003 or Type NPT to ASME B1.20.1-1983. 4.1.3.3 Body end port inside diameter The body end port shall be circular. For unlined valves the body end port inside diameter shall be not less than the nominal inside diameter speci

47、fied in Table 1. DIN EN 1984:2010-10 EN 1984:2010 (E) 8 Table 1 Nominal inside diameter of the body end port Dimensions in millimetres DN PN 10 PN 16 Class 150 PN 25 PN 40 Class 300 PN 63 PN 100 Class 600 Class 8008 8 8 6 8 8 6 8 6 6 6 10 10 10 9 10 10 9 10 9 9 9 12 12 12 12 12 12 12 12 11 11 11 15

48、15 15 13 13 13 13 13 13 13 12 20 20 20 19 19 19 19 19 19 19 18 25 25 25 25 25 25 25 25 25 25 23 32 31 31 31 31 31 31 31 31 31 30 40 40 40 38 38 38 38 38 38 38 36 50 50 50 50 50 50 50 50 50 50 46 65 63 63 63 63 63 63 63 63 63 60 80 78 78 76 76 76 76 76 76 76 - 100 100 100 101 100 100 101 100 100 101

49、- 125 125 125 127 125 125 127 125 125 127 - 150 150 150 152 150 150 152 150 150 152 - 200 200 200 203 200 200 203 200 199 199 - 250 250 250 254 250 250 254 250 247 247 - 300 300 300 304 300 300 304 300 298 298 - 350 343 343 336 336 336 336 336 327 327 - 400 394 394 387 387 387 387 384 375 375 - 450 445 445 438 438 432 432 429 419 419 - 500 495 495 488 488 483 483 479 463 463 - 600 597 597 590 590 584 584 579 558 558 - 700 695 695 692 692 686 686 678