DIN EN 1527-2013 Building hardware - Hardware for sliding doors and folding doors - Requirements and test methods German version EN 1527 2013《建筑五金 滑门和折叠门五金 要求和试验方法 德文版本EN 1527-2013.pdf

《DIN EN 1527-2013 Building hardware - Hardware for sliding doors and folding doors - Requirements and test methods German version EN 1527 2013《建筑五金 滑门和折叠门五金 要求和试验方法 德文版本EN 1527-2013.pdf》由会员分享，可在线阅读，更多相关《DIN EN 1527-2013 Building hardware - Hardware for sliding doors and folding doors - Requirements and test methods German version EN 1527 2013《建筑五金 滑门和折叠门五金 要求和试验方法 德文版本EN 1527-2013.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、March 2013 Translation by DIN-Sprachendienst.English price group 12No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS

2、91.190!$1(“1961405www.din.deDDIN EN 1527Building hardware Hardware for sliding doors and folding doors Requirements and test methods;English version EN 1527:2013,English translation of DIN EN 1527:2013-03Schlsser und Baubeschlge Beschlge fr Schiebetren und Falttren Anforderungen und Prfverfahren;Eng

3、lische Fassung EN 1527:2013,Englische bersetzung von DIN EN 1527:2013-03Quincaillerie pour le btiment Quincaillerie pour portes coulissantes et portes pliantes Exigences et mthodes dessai;Version anglaise EN 1527:2013,Traduction anglaise de DIN EN 1527:2013-03SupersedesDIN EN 1527:1998-12www.beuth.d

4、eIn case of doubt, the German-language original shall be considered authoritative.Document comprises 20 pages 02.13 DIN EN 1527:2013-03 2 A comma is used as the decimal marker. National foreword This document (EN 1527:2013) has been prepared by Technical Committee CEN/TC 33 “Doors, windows, shutters

5、, building hardware and curtain walling” (Secretariat: AFNOR, France), Working Group WG 4 “Building hardware” (lead-management: United Kingdom). The responsible German body involved in its preparation was the Normenausschuss Bauwesen (Building and Civil Engineering Standards Committee), Working Comm

6、ittee NA 005-09-51 AA Schiebe- und Falttrbe-schlge. Amendments This standard differs from DIN EN 1527:1998-12 as follows: a) in Clause 3 “Terms and definitions”, 3.23 design system has been added; b) the determination of grades for fire resistance (fourth digit) has been deleted; c) the grade identi

7、fied for the safety (fifth digit) has been added. Previous editions DIN EN 1527: 1998-12 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1527 January 2013 ICS 91.190 Supersedes EN 1527:1998English Version Building hardware - Hardware for sliding doors and folding doors - Requirements and test m

8、ethods Quincaillerie pour le btiment - Quincaillerie pour portes coulissantes et portes pliantes - Exigences et mthodes dessai Schlsser und Baubeschlge - Beschlge fr Schiebetren und Falttren - Anforderungen und Prfverfahren This European Standard was approved by CEN on 10 November 2012. CEN members

9、are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application t

10、o the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

11、Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lith

12、uania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brusse

13、ls 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1527:2013: EEN 1527:2013 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 Classification 74.1 General 74.2 Category of use (1stdigit)

14、 74.3 Durability (2nddigit) .74.4 Door mass (3rddigit) 74.5 Fire resistance (4thdigit) .74.6 Safety (5thdigit) 74.7 Corrosion resistance (6thdigit) .74.8 Security (7thdigit).84.9 Category of door (8thdigit) 84.10 Initial friction maximum permitted value (9thdigit) 84.11 Example of classification 85

15、Requirements .85.1 Criteria for assessing performances .85.2 General 95.3 Performance requirements for sliding doors and folding door fittings .96 Test methods . 106.1 Test apparatus 106.1.1 Preparation of the test frame . 106.1.2 Test apparatus 106.2 Preparation and installation of the fittings for

16、 tests . 116.2.1 Preparation of the test panels . 116.2.2 Installation of the fittings . 116.3 Test methods . 126.3.1 Performance tests. 126.3.2 Corrosion resistance test 177 Interchangeability . 178 Obligations of the manufacturer . 179 Marking 18DIN EN 1527:2013-03 EN 1527:2013 (E) 3 Foreword This

17、 document (EN 1527:2013) has been prepared by Technical Committee CEN/TC 33 “Doors, windows, shutters and building hardware”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorseme

18、nt, at the latest by July 2013, and conflicting national standards shall be withdrawn at the latest by July 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any

19、 or all such patent rights. This document supersedes EN 1527:1998. A full contribution to the preparation of this document has been made by the European manufacturers organisation “ARGE“. This document is part of a group of European Standards dedicated to building hardware products. The main changes

20、 in this draft as compared with EN 1527:1998 are as follows: identification of grades for fire resistance (4thdigit) in 4.5; grade identified for the safety (5thdigit) in 4.6. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound

21、 to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,

22、 Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 1527:2013-03 EN 1527:2013 (E) 4 1 Scope This European Standard specifies requirements for the manual design system sliding doors and folding doors of the bi-fold type and multi-panel folding doors but exc

23、luding doors and panels. Cycle tests, static load, initial friction and corrosion resistance tests are included for fittings and track only. This document covers door gear for all industrial and residential sliding doors and folding doors. This document does not cover sliding corner doors and light

24、bottom sliding doors. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced documen

25、t (including any amendments) applies. EN 1670, Building hardware Corrosion resistance Requirements and test methods 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 aligner fittings which retain a folding door in a flat and aligned closed posi

26、tion (see Figure 1) 3.2 bottom guide fitting which, with a bottom guide channel, controls the lateral movement of a sliding or folding top hanging door 3.3 bottom guide channel channel section fitted either to the base of a structure or the bottom edge of a door to accommodate the bottom guide 3.4 b

27、ottom pivot axis fitted to the bottom of a folding door which turns in a bottom pivot socket (see Figure 1) 3.5 bottom pivot socket fixed component in which the bottom pivot of a folding door is located (see Figure 1) 3.6 bottom track track fixed to the base of a structure or floor, on which bottom

28、rollers run 3.7 bottom roller fitting attached to the bottom of a door which allows it to run on a bottom rail 3.8 folding door, bi-fold type door formed by two panels connected by hinges and operating on pivots running in a top track with guide DIN EN 1527:2013-03 EN 1527:2013 (E) 5 3.9 heavy slidi

29、ng door, bottom rolling door of mass 100 kg or more with bottom rollers running on a bottom track fixed to the base of the structure or floor, and with a top guide 3.10 heavy sliding door, top hanging door of mass 100 kg or more which is suspended by top hangers running in a top track fixed to an ov

30、erhead structural component, and with a bottom guide 3.11 hinges fittings connecting two panels of a folding door (see Figure 1) 3.12 light sliding door, top hanging door of mass less than 100 kg which is suspended by top hangers running in a top track fixed to an overhead structural component, and

31、with a bottom guide 3.13 multi-panel folding door door formed by two or more panels connected by hinges and suspended by top hangers running in a top track fixed to an overhead structural component, or running on bottom rollers with a top guide in a top track 3.14 stop fitting used to stop a sliding

32、 door at the end of its run 3.15 test cycle all operations from the closed position, to open the test door to the required position and close it again to the closed position 3.16 top bracket support used to carry a top track and secure it to the structure of a building Note 1 to entry: Brackets can

33、be side-wall fixing or ceiling fixing, adjustable or non-adjustable. 3.17 top guide fitting which, with a top guide track, controls the lateral movement of a bottom rolling sliding door 3.18 top guide track track fixed to the top of the structure in which a top guide runs 3.19 top hanger roller fixe

34、d to a top hanging sliding door which allows it to move laterally 3.20 top pivot axis fitted to the top of a folding door which turns in a top pivot socket (see Figure 1) 3.21 top pivot socket fixed component in which the top pivot is located (see Figure 1) DIN EN 1527:2013-03 EN 1527:2013 (E) 6 3.2

35、2 top track tubular section which carries the hangers of sliding and folding top hanging doors (see Figure 1) 3.23 design system collection of components from which a “kit“ may be created for subsequent installation in the works Note 1 to entry: A “design system“ can, for example, be presented in a

36、suppliers catalogue, from which the purchaser/specifier can make a choice. Note 2 to entry: A “design system“ can give rise to one or many different “kits“ (i.e. construction products, defined below). A “design system“ cannot be a construction product, because it is possible only to buy one “kit“ at

37、 a time from the “system“; the “system“ itself cannot be bought. Key 1 track 2 top pivot socket 3 sliders 4 top pivots 5 hinges 6 bottom pivots 7 bottom pivot sockets 8 aligners Figure 1 Definitions DIN EN 1527:2013-03 EN 1527:2013 (E) 7 4 Classification 4.1 General For the purposes of this document

38、, sliding doors and folding doors and their fittings shall be classified according to the nine digit coding system described in 4.2 to 4.10 4.2 Category of use (1stdigit) No grade identified for these products. 4.3 Durability (2nddigit) Six grades of durability are identified for door fittings: grad

39、e 1 = 5 000 test cycles; grade 2 = 10 000 test cycles; grade 3 = 25 000 test cycles; grade 4 = 50 000 test cycles; grade 5 = 75 000 test cycles; grade 6 = 100 000 test cycles. 4.4 Door mass (3rddigit) Four grades are identified for door mass: grade 1 = door up to 50 kg; grade 2 = door from 51 kg to

40、100 kg; grade 3 = door from 101 kg to 330 kg; grade 4 = door over 330 kg. 4.5 Fire resistance (4thdigit) No grade identified for these products. 4.6 Safety (5thdigit) All sliding design systems and sliding folding design systems conforming to this standard shall be classified as grade 1 for safety.

41、4.7 Corrosion resistance (6thdigit) Products are classified from 1 to 5 according to the six grades defined in EN 1670. DIN EN 1527:2013-03 EN 1527:2013 (E) 8 Grade 0 is for products not tested. 4.8 Security (7thdigit) No grade identified for these products. 4.9 Category of door (8thdigit) Three gra

42、des are identified: grade 1 = sliding door; grade 2 = folding door (bi-fold type); grade 3 = multi-panel folding door. 4.10 Initial friction maximum permitted value (9thdigit) Three grades are identified, as shown in Table 1. Table 1 Initial friction maximum permitted value Door mass From 0 kg to 50

43、 kg From 51 kg to 100 kg From 101 kg to 330 kg Over 330 kg Grade 1 50 N 80 N 100 N 5 % of the mass Grade 2 40 N 60 N 5 % of the mass 4 % of the mass Grade 3 30 N 40 N 4 % of the mass 3 % of the mass 4.11 Example of classification - 3 2 - 1 0 - 1 2 This denotes a sliding door with a mass between 51 k

44、g and 100 kg, of which initial friction is equal or less than 60 N, tested to 25 000 cycles, classified as grade 1 for safety and not tested for corrosion resistance. 5 Requirements 5.1 Criteria for assessing performances Performance and finishing requirements for sliding doors and folding door fitt

45、ings shall be assessed according to: static load capacity; effort required to overcome initial friction; durability of fittings; smoothness of operation (bi-fold doors); DIN EN 1527:2013-03 EN 1527:2013 (E) 9 ability to maintain adjustments (bi-fold doors); corrosion resistance. A sample tested acco

46、rding to this document is considered acceptable if it meets the performance requirements stated in this document. 5.2 General Each test panel shall be made in order to meet the following requirements for: Static load test: two times rating of the hangers or bottom rollers; Initial friction test: mas

47、s of the door shall be in accordance with the manufacturers specifications for hangers or bottom rollers; Durability test: mass of the door shall be in accordance with the manufacturers specifications for hangers or bottom rollers. Throughout the durability test, all parts shall remain in serviceabl

48、e condition and shall not require any adjustment. Fittings shall satisfy the requirements of the initial friction test before and after the durability test. Each hanger shall be supplied with assembly accessories and shall be supplied “ready to be mounted“ with the mechanism oiled inside. 5.3 Performance requirements for sliding doors and folding door fittings Sliding doors and folding door fittings sha