DIN EN 14978-2016 Laminate floor coverings - Elements with acrylic based surface layer electron beam cured - Specifications requirements and test methods German version EN 14978 20.pdf

《DIN EN 14978-2016 Laminate floor coverings - Elements with acrylic based surface layer electron beam cured - Specifications requirements and test methods German version EN 14978 20.pdf》由会员分享，可在线阅读，更多相关《DIN EN 14978-2016 Laminate floor coverings - Elements with acrylic based surface layer electron beam cured - Specifications requirements and test methods German version EN 14978 20.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、August 2016 English price group 9No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 97.150!%Ylf“2547367www.din.deDIN E

2、N 14978Laminate floor coverings Elements with acrylic based surface layer, electron beam cured Specifications, requirements and test methods;English version EN 14978:2016,English translation of DIN EN 14978:2016-08Laminatbden Elemente mit einer elektronenstrahlgehrteten Deckschicht auf Acryl-Basis S

3、pezifikationen, Anforderungen und Prfverfahren;Englische Fassung EN 14978:2016,Englische bersetzung von DIN EN 14978:2016-08Revtements de sol stratifis lments parement base acrylique traits par des faisceaux dlectrons Spcifications, exigences et mthodes dessai;Version anglaise EN 14978:2016,Traducti

4、on anglaise de DIN EN 14978:2016-08SupersedesDIN EN 14978:2006-09www.beuth.deDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.Document comprises 12 pages 07.16 2 A comma is used as the decimal marker. National foreword This document

5、(EN 14978:2016) has been prepared by Technical Committee CEN/TC 134 “Resilient, textile and laminate floor coverings” (Secretariat: NBN, Belgium). The responsible German body involved in its preparation was DIN-Normenausschuss Holzwirtschaft und Mbel (DIN Standards Committee Timber and Furniture), W

6、orking Committee NA 042-04-30 AA Laminat-bden. Amendments This standard differs from DIN EN 14978:2006-09 as follows: a) a general definition for laminate floor coverings has been included; b) a defined underlay for the impact resistance test with the large diameter ball has been added; c) requireme

7、nts for castor chair test have been changed; d) requirements for level of use 32 and 33 for floor coverings with a high gloss level have been added; e) test method and requirements for abrasion resistance for floor coverings with a high gloss level have been changed; f) requirements for cigarette re

8、sistance have been deleted; g) technical characteristic micro-scratch resistance has been added; Previous editions DIN EN 14978: 2006-09 DIN EN 14978:2016-08 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14978 March 2016 ICS 97.150 Supersedes EN 14978:2006English Version Laminate floor coveri

9、ngs - Elements with acrylic based surface layer, electron beam cured - Specifications, requirements and test methods Revtements de sol stratifis - lments parement base acrylique traits par des faisceaux dlectrons - Spcifications, exigences et mthodes dessai Laminatbden - Elemente mit einer elektrone

10、nstrahlgehrteten Deckschicht auf Acryl-Basis - Spezifikationen, Anforderungen und Prfverfahren This European Standard was approved by CEN on 27 November 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard th

11、e status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, Fren

12、ch, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria,

13、 Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey

14、andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref.

15、No. EN 14978:2016 EEN 14978:2016 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 5 4 Characteristics . 6 5 Classification . 6 5.1 General 6 5.2 Floor coverings with a common gloss level . 6 5.3 Floor coverings with a high gloss level 7 6 Additio

16、nal characteristics and requirements . 8 7 Marking, designation and packaging . 8 7.1 Marking . 8 7.2 Packaging . 9 8 Test report . 9 Bibliography . 10 DIN EN 14978:2016-08 EN 14978:2016 (E) 3 European foreword This document (EN 14978:2016) has been prepared by Technical Committee CEN/TC 134 “Resili

17、ent, textile and laminate floor coverings”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2016, and conflicting national standards shall be wit

18、hdrawn at the latest by September 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 14978:2006. Compared to EN 14978:

19、2006 the following changes have been made: a) general definition for laminate floor coverings included; b) defined underlay for impact resistance test with the large diameter ball added; c) requirements for castor chair test changed; d) requirements for level of use 32 and 33 for floor coverings wit

20、h a high gloss level added; e) test method and requirements for abrasion resistance for floor coverings with a high gloss level changed; f) requirements for cigarette resistance deleted; g) technical characteristic micro-scratch resistance added. According to the CEN-CENELEC Internal Regulations, th

21、e national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvi

22、a, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 14978:2016-08EN 14978:2016 (E) 4 1 Scope This European Standard specifies characteristics, requirements and test methods for laminate

23、 floor coverings with acrylic based surface layer, electron beam cured as defined in 3.1 and 3.2. It includes a classification system based on EN ISO 10874, giving practical requirements for areas of use and levels of use, to indicate where laminate floor coverings will give satisfactory service and

24、 to encourage the consumer to make an informed choice. It also specifies requirements for marking and packaging. Laminate floor coverings are considered for domestic and commercial levels of use, e.g. for use in domestic kitchens. This standard does not specify requirements related to areas that are

25、 subject to frequent wetting, such as bathrooms, laundry rooms or saunas. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated refe

26、rences, the latest edition of the referenced document (including any amendments) applies. EN 322, Wood-based panels - Determination of moisture content EN 424, Resilient floor coverings - Determination of the effect of simulated movement of a furniture leg EN 425:2002, Resilient and laminate floor c

27、overings - Castor chair test EN 438 (all parts), High-pressure decorative laminates (HPL) Sheets based on thermosetting resins (Usually called Laminates) EN 13329:2016, Laminate floor coverings Elements with a surface layer based on aminoplastic thermosetting resins Specifications, requirements and

28、test methods EN 15468:2016, Laminate floor coverings Elements with directly applied printing and resin surface layer Specifications, requirements and test methods EN 16094, Laminate floor coverings - Test method for the determination of micro-scratch resistance CEN/TS 16354, Laminate floor coverings

29、 - Underlays - Specification, requirements and test methods EN ISO 2813, Paints and varnishes - Determination of gloss value at 20, 60 and 85 (ISO 2813) EN ISO 10874, Resilient, textile and laminate floor coverings - Classification (ISO 10874) ISO 24334, Laminate floor coverings - Determination of l

30、ocking strength for mechanically assembled panels ISO 24336, Laminate floor coverings Determination of thickness swelling after partial immersion in water DIN EN 14978:2016-08EN 14978:2016 (E) 5 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 13329:20

31、16 and the following apply. 3.1 laminate floor covering rigid floor covering, typically in a plank or tile format, with a multiple layer structure: e.g. backer, substrate and dcor Note 1 to entry: The planks/tiles have worked edges that allow the product to be joined together to form a larger integr

32、al unit. The product may vary in surface texture and gloss level. Note 2 to entry: Laminate flooring does not include products having a resilient, stone, textile, wood, leather or metal top surfacing material(s). 3.2 acrylic based surface layer upper decorative layer intended to be the visible side

33、when the floor is installed consisting of resins which are hardened using beams (normally acrylate, methacrylate or similar) and impregnated and surfaced decorative materials (normally paper), which all together are hardened through the application of a sufficient dose of electron beams and constant

34、 pressure Note 1 to entry: The surface layer produced with this technique is called electron-beam pressed laminate (EPL). The surface layer is bonded to a substrate (usually a wood-based panel). 3.3 substrate core material of the laminate floor covering Note 1 to entry: It is generally a particleboa

35、rd, as defined in EN 309, or a dry process fibreboard (MDF) as defined in EN 316 or a so called High Density Fibreboard (HDF) which is a MDF-board with a density 800 kg/m3. 3.4 backer layer opposite to the surface layer used to balance and stabilize the product Note 1 to entry: The backer is general

36、ly made of impregnated papers. 3.5 underlay layer placed between the laminate floor covering and the subfloor to impart specific properties Note 1 to entry: Some laminate floor covering products have the underlay pre-attached directly to the backer. DIN EN 14978:2016-08 EN 14978:2016 (E) 6 3.6 lamin

37、ate floor covering element piece of the floor covering with profiled edges to facilitate assembly at installation Note 1 to entry: See Figure 1 Key 1 surface layer 2 substrate 3 backer 4 underlay (optional) Figure 1 Construction of a laminate floor-covering element 4 Characteristics Laminate floor c

38、overings according to this standard shall conform to the general requirements given in EN 13329:2016, Table 1, with the following modifications: For special applications, such as decorative pattern effects, tighter tolerances shall be permitted if necessary. Tolerances of the tongue and groove shall

39、 be such that when, for the purposes of testing, the elements are assembled without glue, the maximum permissible opening and height difference values are not exceeded. To determine the capability of laminate floor coverings to withstand ambient humidity variations, a laboratory test in controlled c

40、onditions shall be made. 5 Classification 5.1 General Prior to classification testing, the specular gloss level of the laminate floor covering shall be determined in accordance with EN ISO 2813, with a detection angle of 60. A distinction shall be made between two specular gloss levels of the surfac

41、e layer: common gloss level: specular gloss level 85 units; high gloss level: specular gloss level 85 units. 5.2 Floor coverings with a common gloss level Laminate floor coverings conforming to this standard with a common gloss level shall be classified as being suitable for different levels of use

42、according to the requirements specified in EN 13329:2016, Table 2, when tested by the methods given therein. Classification shall conform to the scheme specified in EN ISO 10874. DIN EN 14978:2016-08 EN 14978:2016 (E) 7 5.3 Floor coverings with a high gloss level Laminate floor coverings conforming

43、to this standard with a high gloss level shall be classified as being suitable for different levels of use according to the requirements specified in Table 1, when tested by the methods given therein. Classification shall conform to the scheme specified in EN ISO 10874. For the large ball impact tes

44、t a standard EPS foam of (1,8 0,2) mm thickness, with a CS value of (60 10) kPa and with PC-value of (0,9 0,1) mm shall be used. The three parameters of the foam shall be determined according to CEN/TS 16354.1)Table 1 Classification requirements and levels of use for floor coverings with a high glos

45、s level Level of use Domestic Commercial Moderate General Heavy Moderate General Heavy Class 21 22 23 31 32 33 Test method Abrasion resistance 1 000 revolutions 2 000 revolutions 4 000 rev. 6 000 rev. EN 15468:2016, Annex A Impact resistance Small ball 8 N 12 N 15 N EN 13329:2016, Annex H Big ball 5

46、00 mm 750 mm 1000 mm Resistance to staining 4, (groups 1 and 2) 3, (group 3) 5, (groups 1 and 2) 4, (group 3) EN 4382 Effect of a furniture leg - No damage shall be visible, when tested with foot type 0 EN 424 Effect of a castor chair - 25 000 cycles, No damageaEN 425:2002 b Thickness swelling 20 %

47、18 % 15 % ISO 24336 Locking strength - fl0,2 1 kN/m (length) fs0,2 2 kN/m (width) ISO 24334 Surface soundness 1,0 N/mm2 1,25 N/mm2EN 13329:2016, Annex D aNo visible damage on the surface of the assembled test area caused by detachment of layers, opening of joints, or crazing. Ignore any flattening o

48、r change in appearance, e.g. change in gloss. bUsing soft castor wheels W PU (95 5) Shore A” dropping “except for class 34 wheels H PA (95 5) Shore A. 1) The product “Selitflex 1,6 mm” made by Selit Dmmtechnik GmbH is an example of a suitable product available commercially. This information is given

49、 for the convenience of users of this European Standard and does not constitute an endorsement by CEN of this product. Equivalent products may be used if they can be shown to lead to the same results. DIN EN 14978:2016-08EN 14978:2016 (E) 8 6 Additional characteristics and requirements When any of the characteristics given in Table 2 are requested for specific applications, the