DIN EN 1383-2016 Timber structures - Test methods - Pull through resistance of timber fasteners German version EN 1383 2016《木结构 试验方法 木制紧固件的楔入阻力 德文版本EN 1383-2016》.pdf

《DIN EN 1383-2016 Timber structures - Test methods - Pull through resistance of timber fasteners German version EN 1383 2016《木结构 试验方法 木制紧固件的楔入阻力 德文版本EN 1383-2016》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 1383-2016 Timber structures - Test methods - Pull through resistance of timber fasteners German version EN 1383 2016《木结构 试验方法 木制紧固件的楔入阻力 德文版本EN 1383-2016》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、July 2016 English price group 9No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 91.080.20!%X9t“2532281www.din.deDIN

2、EN 1383Timber structures Test methods Pull through resistance of timber fasteners;English version EN 1383:2016,English translation of DIN EN 1383:2016-07Holzbauwerke Prfverfahren Prfung von Holzverbindungsmitteln auf Kopfdurchziehen;Englische Fassung EN 1383:2016,Englische bersetzung von DIN EN 1383

3、:2016-07Structures en bois Mthodes dessai Rsistance la traverse de la tte dlments de fixation travers le bois;Version anglaise EN 1383:2016,Traduction anglaise de DIN EN 1383:2016-07SupersedesDIN EN 1383:2000-03www.beuth.deDocument comprises 13 pagesDTranslation by DIN-Sprachendienst.In case of doub

4、t, the German-language original shall be considered authoritative.06.16DIN EN 1383:2016 -07 2 A comma is used as the decimal marker. National foreword This document (EN 1383:2016) has been prepared by Technical Committee CEN/TC 124 “Timber structures” (Secretariat: AFNOR, France). The responsible Ge

5、rman body involved in its preparation was DIN-Normenausschuss Bauwesen (DIN Standards Committee Building and Civil Engineering), Working Committee NA 005-04-01 AA Holzbau (SpA zu CEN/TC 124, CEN/TC 250/SC 5). Amendments This standard differs from DIN EN 1383:2000-03 as follows: a) EN 28970 has been

6、replaced by EN ISO 8970; b) the figures have been improved. Previous editions DIN EN 1383: 2000-03 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1383 February 2016 ICS 91.080.20 Supersedes EN 1383:1999English Version Timber structures - Test methods - Pull through resistance of timber fastene

7、rs Structures en bois - Mthodes dessais - Rsistance la traverse de la tte dlments de fixation travers le bois Holzbauwerke - Prfverfahren - Prfung von Holzverbindungsmitteln auf Kopfdurchziehen This European Standard was approved by CEN on 19 December 2015. CEN members are bound to comply with the C

8、EN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management C

9、entre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as

10、the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Neth

11、erlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rig

12、hts of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1383:2016 EEN 1383:2016 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Symbols and abbreviations . 5 5 Materials . 7 5.1 Timber and wo

13、od-based products 7 5.2 Fasteners 7 6 Test methods 7 6.1 General 7 6.2 Conditioning 7 6.3 Fabrication of test pieces . 7 6.4 Apparatus . 7 6.5 Test procedure . 7 6.6 Test results . 10 6.7 Test report 10 Bibliography . 11 DIN EN 1383:2016-07 EN 1383:2016 (E) 3 European foreword This document (EN 1383

14、:2016) has been prepared by Technical Committee CEN/TC 124 “Timber Structures”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2016, and conflict

15、ing national standards shall be withdrawn at the latest by August 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document

16、supersedes EN 1383:1999. Compared to EN 1383:1999, the following changes have been made: replacement of EN 28970 by EN ISO 8970; improvement to figures and definitions. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to imp

17、lement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romani

18、a, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 1383:2016-07 EN 1383:2016 (E) 4 1 Scope This European Standard specifies the test method for determining the resistance of timber to the head pull through of timber fasteners. In this standard timber includes so

19、lid timber, glued laminated timber and wood-based products. The test method applies to all types of nails, screws and staples excluding screws with fully threaded shank. 2 Normative references The following documents, in whole or in parts, are normatively referenced in this document and are indispen

20、sable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 322, Wood-based panels - Determination of moisture content EN 323, Wood-based panels - Determination of densit

21、y EN 14592, Timber structures Dowel-type fasteners Requirements EN 26891:1991, Timber structures - Joints made with mechanical fasteners - General principles for the determination of strength and deformation characteristics (ISO 6891:1983) EN ISO 8970:2010, Timber structures - Testing of joints made

22、 with mechanical fasteners - Requirements for wood density (ISO 8970:2010) ISO 13061-1, Physical and mechanical properties of wood Test methods for small clear wood specimens Part 1: Determination of moisture content for physical and mechanical tests ISO 13061-2, Physical and mechanical properties o

23、f wood Test methods for small clear wood specimens Part 2: Determination of density for physical and mechanical tests 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 staple double-bent, u-shaped piece of round, square, rectangular or oval wir

24、e with pointed legs 3.2 staple crown connection between the two staple legs 3.3 staple leg diameter nominal diameter of a round staple leg, the side length of a rectangular leg, or the diameter of an oval cross section as defined in EN 14592 3.4 staple length length of each staple leg, including poi

25、nt DIN EN 1383:2016-07 EN 1383:2016 (E) 5 3.5 staple crown width width across the staple legs 3.6 head pull through parameter parameter measuring the resistance of a timber test piece to the pulling through of the head of a timber fastener or the crown of a staple Note 1 to entry See Figures 1 and 2

26、. Note 2 to entry For other timber fasteners the definitions of EN 14592 apply. 4 Symbols and abbreviations For the purposes of this document, the following symbols and abbreviations apply. a staple crown width, see Figure 1, in millimetres D(I.2)dimensions of hole in steel plate in millimetres d no

27、minal value of the diameter of the fastener as defined in EN 14592, in millimetres dheffective diameter of fastener head (for nails or screws), or, see Figure 1, width of staple crown, in millimetres. For a non-circular head dhis the diameter of a circle with an area equal to that of the head Fmaxma

28、ximum pull through load, in newtons fheadpull through parameter, in newtons per square millimetres t timber thickness, in millimetres crnangle between the direction of a staple crown and the grain direction or the main direction of the wood based products, respectively, see Figure 2, in degrees DIN

29、EN 1383:2016-07 EN 1383:2016 (E) 6 Key dhis head diameter a is staple crown width Figure 1 Staple, screw and nail dimensions Key 1 is the fibre direction Figure 2 Angle between the staple direction and the grain direction or the main direction DIN EN 1383:2016-07 EN 1383:2016 (E) 7 5 Materials 5.1 T

30、imber and wood-based products The solid timber shall be selected in accordance with the method given in EN ISO 8970:2010. The specification of the LVL, glued laminated timber and wood-based products shall be established. The products used for the individual test pieces shall be representative of the

31、 class or range of product to which they belong and the relevant properties shall be declared. 5.2 Fasteners The specification of nails, screws or staples shall be established. 6 Test methods 6.1 General The moisture content and density of the timber or wood-based products at test shall be determine

32、d as specified in ISO 13061-1, ISO 13061-2, EN 322 and EN 323 as appropriate. 6.2 Conditioning The test pieces shall be manufactured with the timber or wood based products at an equilibrium moisture content corresponding to (20 2) C and (65 5) % relative humidity. The material is conditioned when it

33、 attains constant mass. Constant mass is considered to be attained when the results of two successive weightings, carried out at an interval of 6 h, do not differ by more than 0, 1 % off the mass of the material. For certain investigations other moisture conditioning can be appropriate, and shall be

34、 reported. 6.3 Fabrication of test pieces The axis of the fastener shall be perpendicular to the surface, see Figure 3. The insertion of fasteners shall follow normal preparation (e.g. pre-boring) and practice. The test piece size shall be as given in Table 1. Where the test pieces are of solid timb

35、er, half of the fasteners shall be inserted radially to the growth rings and half tangentially to the growth rings. Test shall be made with test pieces with crn= 30. If wood-based products are included in the test piece the test shall be carried out at either crn= 30 or crn= 60, whichever gives the

36、smallest load carrying capacity. Table 1 Test pieces Test piece material Test piece size (minimum) Solid timber 4 t x 4 t Where t 7 d Wood based products 4 t x 4 t Where t = panel thickness as produced 6.4 Apparatus The pieces shall be tested in an apparatus as shown in Figure 4. 6.5 Test procedure

37、The apparatus used shall be as required in Clause 7 of EN 26891:1991. The test piece shall be placed in a device ensuring the application of the pull through force along the axis of the fastener. DIN EN 1383:2016-07 EN 1383:2016 (E) 8 Pull the fastener through the test piece material with a continuo

38、us movement of the head of the testing machine. The rate of movement shall be such that the time taken to reach Fmaxis 300s 120s. Determine Fmaxto an accuracy of 1 %. Key a nails or screws b staples Figure 3 Test specimens for pulling through testing DIN EN 1383:2016-07 EN 1383:2016 (E) 9 Key 1 Stee

39、l plate with a circular hole (diameter D) for nails and screws and a rectangular hole (side lengths D1and D2) for staples. D (2t + dh) D1 (2t + a) D2 (2t + dh) Figure 4 Test arrangement for pull through testing DIN EN 1383:2016-07 EN 1383:2016 (E) 10 6.6 Test results The pull through parameter, fhea

40、d, shall be determined from the equations: =maxhead2hFfdfor nails and screws (1) or =maxhdheadFfafor staples (2) The symbols are as given in Clause 4. 6.7 Test report The test report shall contain the following information: a) sampling procedure; b) specification of the timber; c) dimensions, densit

41、y, moisture content and conditioning history of the test pieces; d) diagram showing the layout of the fasteners and the method of insertion used in the test pieces; e) angle, crn, between staple crown and grain as used in the test; f) number of test pieces used; g) specification (including shape, ge

42、ometry, dh) and number of fasteners (type, sizes, material, surface coating or condition and other particulars); h) time to failure; i) individual test results, including Fmax, mean values and standard deviations, and description of the mode of failure. NOTE Characteristic values can be determined using EN 14358. DIN EN 1383:2016-07 EN 1383:2016 (E) 11 Bibliography 1 EN 1381, Timber structures - Test methods - Load bearing stapled joints 2 EN 14358, Timber structures - Calculation of characteristic 5-percentile values and acceptance criteria for a sample DIN EN 1383:2016-07