DIN EN 13420-2011 Windows - Behaviour between different climates - Test method German version EN 13420 2011《窗 不同气候下的性能 试验方法 德文版本EN 13420-2011》.pdf

《DIN EN 13420-2011 Windows - Behaviour between different climates - Test method German version EN 13420 2011《窗 不同气候下的性能 试验方法 德文版本EN 13420-2011》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 13420-2011 Windows - Behaviour between different climates - Test method German version EN 13420 2011《窗 不同气候下的性能 试验方法 德文版本EN 13420-2011》.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、July 2011 Translation by DIN-Sprachendienst.English price group 10No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 9

2、1.060.50!$sP“1805845www.din.deDDIN EN 13420Windows Behaviour between different climates Test methodEnglish translation of DIN EN 13420:2011-07Fenster Differenzklima PrfverfahrenEnglische bersetzung von DIN EN 13420:2011-07Fentres Comportement entre climats diffrents Mthode dessaiTraduction anglaise

3、de DIN EN 13420:2011-07SupersedesDIN V ENV 13420:2000-08www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.1507.11 DIN EN 13420:2011-07 A comma is used as the decimal marker. National foreword This standard has been prepared by Techni

4、cal Committee CEN/TC 33 “Doors, windows, shutters, building hardware and curtain walling” (Secretariat: AFNOR, France). The responsible German body involved in its preparation was the Normenausschuss Bauwesen (Building and Civil Engineering Standards Committee), Working Committee NA 005-09-01 AA Tre

5、n, Tore, Fenster, Abschlsse, Baubeschlge und Vorhangfassaden. Amendments This standard differs from DIN V ENV 13420:2000-08 as follows: a) the status of the document has been changed from ENV to EN; b) the German title has been added among the titles of the standard; c) the contents have been update

6、d respectively revised; d) the description of test method 2 in Clause 1 has been rephrased; e) the description of the annexes has been rephrased; f) in Subclause 3.1, a reference to Annexes A and B has been integrated at the end; g) in Clause 4, the description of the principle tests has been split

7、into the test procedure vapour diffusion and stability; h) in Clause 8, the reference to the values of EN 1121 has been deleted because the values given in Table 1 are completely different to those in EN 1121; i) the tolerances have been integrated in Table 1; j) the status of Annex B has been chang

8、ed into a normative annex. Previous editions DIN V ENV 13420: 2000-08 2 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13420 April 2011 ICS 91.060.50 Supersedes ENV 13420:2000English Version Windows - Behaviour between different climates - Test method Fentres - Comportement entre climats diffr

9、ents - Mthode dessai Fenster - Differenzklima - Prfverfahren This European Standard was approved by CEN on 10 March 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard witho

10、ut any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other l

11、anguage made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Den

12、mark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALIS

13、ATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13420:2011: EEN 13420:2011 (E) 2 Contents Page Foreword 3Introduction .41 Scope 52 Norma

14、tive references 53 Terms and definitions .64 Principle of tests 64.1 Vapour diffusion 64.2 Stability .75 Test facility .76 Dimensions of the test specimens.77 Preparation for test 78 Test conditions 79 Test methods 810 Test sequence . 1011 Test report . 10Annex A (informative) Design principles . 12

15、Annex B (normative) Survey of general design criteria where tests are not necessary 13DIN EN 13420:2011-07 EN 13420:2011 (E) 3 Foreword This document (EN 13420:2011) has been prepared by Technical Committee CEN/TC 33 “Doors, windows, shutters, building hardware and curtain walling”, the secretariat

16、of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withdrawn at the latest by October 2011. Attention is drawn to

17、the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes ENV 13420:2000. The main modifications to ENV 13420:2000 are: a) Status of document

18、 changed from ENV to EN; b) The German title has been added among the titles of the standard; c) The Contents have been updated respectively revised; d) The description of test method 2 in Clause 1 has been rephrased; e) The description of the annexes has been rephrased; f) In 3.1 a reference to Ann

19、exes A and B has been integrated at the end; g) In Clause 4 the description of the principle tests has been split into the test procedure vapour diffusion and stability; h) In Clause 8 the reference to the values of EN 1121 has been deleted because the values given in Table 1 are completely differen

20、t to those in EN 1121; i) Tolerances have been integrated in Table 1; j) The status of Annex B has been changed into a normative annex. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Au

21、stria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom

22、. DIN EN 13420:2011-07 EN 13420:2011 (E) 4 Introduction Through climatic loading of the windows it is possible in the case of unfavourable designs that the frames of windows manufactured of different materials may: decay through accumulation of moisture and may thus be damaged; this moisture may com

23、e from water vapour diffusion and condensation; be unable to fulfil their basic functions (serviceability, air permeability) because of unacceptable deformations. DIN EN 13420:2011-07 EN 13420:2011 (E) 5 1 Scope This European Standard specifies the test methods for evaluating: the risks of decay of

24、openable and fixed windows manufactured of different materials through increased moisture accumulation as a result of condensation or water vapour diffusion; the influence of deformation on basic performances of openable and fixed windows manufactured of different materials exposed to different clim

25、ates between their external and internal faces. Three test methods are to be differentiated. They take into account different cases of loadings. Test method 1: For designs with low resistance to water vapour diffusion (normally designs with water vapour equalization holes); the test procedure is to

26、be used for cross-sections where the danger is given by the moisture accumulation as a result of the condensation of moisture between the planking and the timber (see Annex A (informative), Figure A.1). Test method 2.1 and 2.2: For designs with high resistance to water vapour diffusion (normally des

27、igns without water vapour equalization holes); the test procedure is to be used for cross-sections where the danger is given by the condensation of the moisture between the surface of the inner profile and the inner surface of the outer profile by having a different water vapour diffusion (see Annex

28、 A (informative), Figures A.2 and A.3). Test method 3: For designs being sensitive to deformation; the test procedure is to be used for cross-sections where they are sensitive to the function through deformation as a result of climatic loading. This European Standard defines the test procedures whic

29、h are to be used in dependence of the potential risk of the design. This European Standard is relevant to initial type testing, i. e. to developments or changes in designs. It is not relevant to routine quality control or to proven designs. NOTE Designs are included in Annex A (informative). Annex B

30、 (normative) is the survey of general design criteria where tests are not necessary. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of t

31、he referenced document (including any amendments) applies. EN 1026, Windows and doors Air permeability Test method EN 1121:2000, Doors Behaviour between two different climates Test method EN 12046-1, Operating forces Test method Part 1: Windows EN 12207, Windows and doors Air permeability Classifica

32、tion EN 12519:2004, Windows and pedestrian doors Terminology EN 13115, Windows Classification of mechanical properties Racking, torsion and operating forces DIN EN 13420:2011-07 EN 13420:2011 (E) 6 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12519

33、:2004 and the following apply. 3.1 design with low resistance to water vapour diffusion design which is regarded as being a design with low water vapour diffusion when moisture conditioned by water vapour diffusion can be drained in the cross-section in a controlled way under specified service condi

34、tions, e.g. through sufficient ventilation NOTE See Annex A (informative) and B (normative). 3.2 design with high resistance to water vapour diffusion design which is regarded as being a design with high resistance to water vapour diffusion when as a result of profile coverings a sufficient draining

35、 of the moisture conditioned by water vapour diffusion is impaired in the combined profile 3.3 design being sensitive to deformation design which is regarded as being sensitive to deformation when under specified service conditions the relative expansion (thermal or hygrometrical) of the profile may

36、 impair the basic functions of the window (e.g. operating forces, air permeability) 3.4 window manufactured of different materials window whose frame (or sash or both) members are manufactured of non-identical materials, operating hardware being excluded EXAMPLES Typical examples: basic timber windo

37、ws clad with aluminium or PVC profiles; basic aluminium windows clad with timber (solid profiles or veneers); basic plastic windows clad with aluminium profiles. 3.5 orientation side 1 orientation with an inward looking face 3.6 orientation side 2 orientation with an outward looking face 3.7 wet spo

38、t visible moisture accumulation, after climatic exposure, at the interface between timber (or any other hygroscopic materials) and another material 4 Principle of tests 4.1 Vapour diffusion In order to have a temperature below dew point in composite profiles, a gradient of water vapour diffusion and

39、 a gradient of temperature are created; the window is exposed to this double gradient for a specified time during which the water content of hygroscopic elements is checked. DIN EN 13420:2011-07 EN 13420:2011 (E) 7 4.2 Stability A gradient of temperature between the 2 sides of window is created and

40、the window is exposed to this gradient for a specified time and measurement of deformations and functional deformations are carried out. 5 Test facility The test facility is defined in EN 1121. In addition the following test facilities are required: a measuring device for determining the moisture co

41、ntent; an electric hygrometer which is properly calibrated for determining the moisture content of the timber and which has to have an accuracy of 1 %; and a measuring device for determining the deformation with an accuracy of 0,1 mm. 6 Dimensions of the test specimens For the test methods 1 and 2 t

42、he test results are independent of the dimensions. For that reason, the dimension can be agreed upon between the test laboratory and the applicant. In the case of designs sensitive to deformation (test method 3) the largest overall dimension foreseen by the manufacturer is to be tested to ensure the

43、 validity of the test. The test results obtained at the foreseen maximum dimensions of the tested profile system can be extrapolated to smaller width and height without additional testing. 7 Preparation for test The test specimen shall be mounted taking into account the installation instructions as

44、defined and published by the manufacturer. The test specimen shall be fixed in the test rig plumb without any twists or bends, which may influence the test results. The specimen shall be fully operable and shall be opened and closed five times before the test. During the test the windows shall be se

45、cured in a closed and locked position. 8 Test conditions The test conditions subsequently listed shall be used in connection with the test methods in Clause 9. DIN EN 13420:2011-07 EN 13420:2011 (E) 8 Table 1 Test methods for designs with low and high resistance to water vapour diffusion Test method

46、 Test climate Side 1 Side 2 Cycle/ durability Air temperature1C Relative humidity (U) % Air temperature2 C Relative humidity (U) % 1 A 23 2 50 5 -10 2 See Figure 1 B 23 2 50 5 60 2 - (12 h) 2.1 C 23 2 70 5 3 2 80 5 30 days 60 daysa 2.2 A 23 2 50 5 -10 2 - 30 days 60 daysaaUntil the constant moisture

47、 content of the hygroscopic materials or visible condensation is reached in the profile.Table 2 Test methods for designs sensitive to deformation Test method Test climate Side 1 Side 2 Cycle/durability Air temperature1C Relative humidity (U) % Air temperature 2C Relative humidity (U) % 3 A 23 3 50c

48、5 -10 3 - 24 h D 23 3 50c 5 70a, b ,d, e 3 - 24 haThe reference temperature (according to EN 1121:2000, 5.2) for heating up the surface by radiation. b All test results obtained at 75C (worst case) can be extrapolated to 70 C without additional testing. cFor non hygroscopic materials the relative hu

49、midity need not be regulated. dFor nonhygroscopic materials also a temperature difference ( ) of 47 C may be used, if the upper temperature remains below the softening point of the material. eAlternatively to the method given in EN 1121 (radiation), the temperature may be produced by hot air. The surface temperature of the specimen shall not rise above the surface temperature resulting from radiation when mea