DIN EN 12613-2009 Plastics warning devices for underground cables and pipelines with visual characteristics English version of DIN EN 12613 2009-09《具有可视特性的地下电缆和管线用塑料报警装置 英文版本DIN EN.pdf

《DIN EN 12613-2009 Plastics warning devices for underground cables and pipelines with visual characteristics English version of DIN EN 12613 2009-09《具有可视特性的地下电缆和管线用塑料报警装置 英文版本DIN EN.pdf》由会员分享，可在线阅读，更多相关《DIN EN 12613-2009 Plastics warning devices for underground cables and pipelines with visual characteristics English version of DIN EN 12613 2009-09《具有可视特性的地下电缆和管线用塑料报警装置 英文版本DIN EN.pdf（19页珍藏版）》请在麦多课文档分享上搜索。

1、September 2009DEUTSCHE NORM English price group 11No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 13.320; 83.140.99!$Y

2、l“1547391www.din.deDDIN EN 12613Plastics warning devices for underground cables and pipelines withvisual characteristicsEnglish version of DIN EN 12613:2009-09Warneinrichtungen aus Kunststoff mit visuellen Eigenschaften fr erdverlegte Kabel undRohrleitungenEnglische Fassung DIN EN 12613:2009-09Super

3、sedesDIN EN 12613:2001-07www.beuth.deDocument comprises 19 pagesDIN EN 12613:2009-09 National foreword This standard has been prepared by Technical Committee CEN/TC 249 “Plastics” (Secretariat: NBN, Belgium). The responsible German body involved in its preparation was the Normenausschuss Kunststoffe

4、 (Plastics Standards Committee), Technical Committee NA 054-05-10 AA Warneinrichtungen aus Kunststoff fr erdverlegte Kabel- und Rohrleitungen. To supplement this European Standard, reference is made to the following German Standards: DIN 54841-3, Plastic warning devices for buried cables and pipelin

5、es Part 3: Detectable table DIN 54841-5, Plastic warning devices for underground cables and pipelines Part 5: Cable cover These standards are largely based on the present DIN EN 12613 and include further specifications concer-ning different laying conditions. Amendments This standard differs from DI

6、N EN 12613:2001-07 as follows: a) The test method for assessing the visual characteristics of the warning devices (Annex A) has been revised. b) Test conditions for assessing the visual characteristics of the warning devices wider than 500 mm have been included. c) Normative references have been upd

7、ated. d) The subclauses relating to the laying characteristics have been revised. e) The subclauses relating to the resistance against micro-organisms, to UV-light and temperature stability have been revised. Previous editions DIN V 54841-1: 1994-10 DIN EN 12613: 2001-07 2 EUROPEAN STANDARD NORME EU

8、ROPENNE EUROPISCHE NORM EN 12613 June 2009 ICS 13.320; 83.140.99 Supersedes EN 12613:2009 English Version Plastics warning devices for underground cables and pipelines with visual characteristics Dispositifs avertisseurs caractristiques visuelles, en matire plastique, pour cbles et canalisations ent

9、errs Warneinrichtungen aus Kunststoff mit visuellen Eigenschaften fr erdverlegte Kabel und Rohrleitungen This European Standard was approved by CEN on 20 May 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandar

10、d the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French,

11、German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech

12、 Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPE

13、N DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12613:2009: EEN 12613:2009 (E) 2 Contents PageForeword 3Introduction .41 Sc

14、ope 52 Normative references 53 Terms and definitions .54 Material .65 Requirements .65.1 Colour .65.2 Appearance and colour fastness .65.3 Dimensional characteristics .65.4 Laying characteristics .75.4.1 General 75.4.2 Tensile withstand strength .75.4.3 Transversal rigidity 75.4.4 Flatness 75.5 Visu

15、al warning characteristics .75.6 Resistance against micro-organisms 75.7 Resistance to UV-light .75.8 Temperature stability 85.9 Resistance of printing .85.10 Marking .86 Test methods 86.1 Test pieces and test conditions .86.2 Colour fastness 86.3 Tensile withstand strength .86.3.1 Test pieces .86.3

16、.2 Apparatus .96.3.3 Procedure .96.4 Transversal rigidity 96.5 Flatness . 107 Factory production control tests 108 Test report . 11Annex A (normative) Determination of visual warning characteristics by simulation of trench opening 12A.1 Principle . 12A.2 Apparatus 12A.3 Test pieces 16A.4 Conditionin

17、g and test temperature . 16A.5 Procedure 16A.6 Test conditions for warning devices wider than 500 mm . 16Annex B (normative) Chemical resistance to ammonium sulphide . 17B.1 Apparatus 17B.2 Preparation of test pieces 17B.3 Procedure 17DIN EN 12613:2009-09 EN 12613:2009 (E) 3 Foreword This document (

18、EN 12613:2009) has been prepared by Technical Committee CEN/TC 249 “Plastics”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2009, and conflicti

19、ng national standards shall be withdrawn at the latest by December 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document

20、 supersedes EN 12613:2001. This document is a revision of EN 12613:2001 with the following modifications: review of the test method for assessing the visual characteristics of the warning devices (Annex A) while keeping the principle and the functional features specified in EN 12613:2001; addition o

21、f test conditions for assessing the visual characteristics of the warning devices wider than 500 mm; updating of the normative references; improvement of the subclauses for the laying characteristics; improvement of the subclauses for the resistance against micro-organisms, to UV-light and temperatu

22、re stability. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ir

23、eland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. DIN EN 12613:2009-09 EN 12613:2009 (E) 4 Introduction Visual warning devices are used for the manual or mechanized laying of cabl

24、es and piping buried in ground such as electrical power cables, communication cables, pressure and non-pressure piping systems. The purpose of warning devices is to warn of the presence of a pipe or a cable, when opening a trench, to indicate its orientation and to identify the equipment protected.

25、The warning devices are expected to last at least the lifetime of the equipments with which they are associated. DIN EN 12613:2009-09 EN 12613:2009 (E) 5 1 Scope This European Standard specifies the material, mechanical and functional (fitness for purpose) requirements for warning devices with visua

26、l characteristics manufactured from plastics, intended to indicate the presence of cables and piping systems buried in ground when opening trenches and more generally during digging work. This European Standard also specifies the test methods referred to in this document. This European Standard is a

27、pplicable to two types of visual warning devices: tapes (type 1) and meshes (type 2). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of

28、the referenced document (including any amendments) applies. EN 60898-1:2003, Electrical accessories Circuit breakers for overcurrent protection for household and similar installations Part 1: Circuit-breakers for a.c. operation (IEC 60898-1:2002, modified) EN ISO 175, Plastics Method of test for det

29、ermination of the effects of immersion in liquid chemicals (ISO 175:1999) EN ISO 846, Plastics Evaluation of the action of microorganisms (ISO 846:1997) EN ISO 4892-1, Plastics Methods of exposure to laboratory light sources Part 1: General guidance (ISO 4892-1:1999) 3 Terms and definitions For the

30、purposes of this document, the following terms and definitions apply. 3.1 type 1 warning device strip manufactured from plastics to warn of the presence of underground cables or pipes during excavation 3.2 type 2 warning device mesh/net manufactured from plastics to warn of the presence of undergrou

31、nd cables or pipes during excavation 3.3 nominal width of a warning device (W0) overall width of the warning device, as declared by the manufacturer, in millimetres 3.4 longitudinal direction direction corresponding to the extrusion direction, parallel to the length of the reel 3.5 transversal direc

32、tion direction parallel to the width (at right angle to the length) DIN EN 12613:2009-09 EN 12613:2009 (E) 6 4 Material The material shall be made of any thermoplastic material, e.g. polyethylene (PE) or polypropylene (PP), to which are added those additives necessary for the manufacture of warning

33、devices conforming to the requirements of this standard. The use of own or external reprocessable materials or recyclable materials shall be permitted for the manufacture of warning devices conforming to the requirements of this standard. The material, additives, colour masterbatches and inks for pr

34、inting, if added, shall have no detrimental effect on the environment. 5 Requirements 5.1 Colour The colour of the warning device shall be as agreed between the manufacturer and the purchaser. 5.2 Appearance and colour fastness The appearance, colouring and marking of the warning device shall not ex

35、hibit any change when tested in accordance with 6.2. No discoloration or change of the initial colour shall be permitted. Only a change in surface appearance (e.g. gloss/matt) shall be permitted. For a given type of warning device (design, width), the colour fastness shall be tested for each colour.

36、5.3 Dimensional characteristics The nominal width, W0, of the warning device shall be as agreed between the manufacturer and the purchaser. For type 1 warning devices, each individual value of the width shall be equal or greater than 50 mm and the outside edges of the warning device shall be straigh

37、t and parallel. The deviation of each outside edge, towards outside or inside relatively to the mean line, shall be less or equal to 2 mm. For type 2 warning devices, the dimensional characteristics shall conform to Table 1 and it is recommended that the minimum reel length is equal or greater than

38、100 m or as agreed between the manufacturer and the purchaser. Table 1 Dimensional characteristics Characteristics Unit Requirements Width (W) mm (W0 0,1W0 W W0+ 0,1W0) and W 50 (W0 10 W W0+ 10) W0 100 W0 100 Internal perimeter of an opening mm 360 Strand width mm 1 for an internal perimeter 160 2 f

39、or an Internal perimeter 160 DIN EN 12613:2009-09 EN 12613:2009 (E) 7 5.4 Laying characteristics 5.4.1 General For ease of use, the warning devices need sufficient rigidity, flatness and longitudinal mechanical strength to maintain their shape. 5.4.2 Tensile withstand strength When tested in accorda

40、nce with 6.3, the type 1 warning device shall withstand a load of 200 N during 5 min in the longitudinal direction, without starting of the separation of the weak points, if any, and shall not exhibit a reduction of more than 20 % of its width after removal of the load. When tested in accordance wit

41、h 6.3, the type 2 warning device shall withstand a load of 300 N during 5 min in longitudinal direction, without starting of the separation of the weak points, if any, and shall not exhibit a reduction of more than 20 % of its width after removal of the load. 5.4.3 Transversal rigidity When tested i

42、n accordance with 6.4, the deflection of outsides edges of the warning device shall be less or equal to W0 /4. If the nominal width of the warning device is greater than 500 mm, this requirement shall not apply. 5.4.4 Flatness When tested in accordance with 6.5, the warning device shall not exhibit

43、at any point a separation with respect to the reference surface greater than W0 /4. 5.5 Visual warning characteristics The visual characteristics of the warning devices are assessed by means of a test which simulates the opening of a trench with the bucket of an excavator. See A.1. When tested in ac

44、cordance with Annex A, the warning device shall exhibit at least one single part of a minimum length of 200 mm outside of the movable plate (which simulates the bucket) and at least one single part of a minimum length of 200 mm in the frame (which simulate the trench). The width of the visible parts

45、 of warning device shall be greater or equal to 2 mm. 5.6 Resistance against micro-organisms The resistance against micro-organisms shall be determined only for the warning devices made from materials other than polyethylene (PE) or polypropylene (PP). When tested in accordance with EN ISO 846 and t

46、he test conditions as specified by the purchaser, the warning device shall not exhibit any change. 5.7 Resistance to UV-light If required, the warning device shall be resistant to UV-light. When tested in accordance with the guidance provided by EN ISO 4892-1 and its subsequent parts, and the test m

47、ethod and conditions as specified by the purchaser, the warning device shall conform to the requirement as specified by the purchaser. If the warning device is not resistant to UV-light, it shall be protected by suitable packaging, as agreed between manufacturer and purchaser. DIN EN 12613:2009-09 E

48、N 12613:2009 (E) 8 5.8 Temperature stability If required, the temperature stability of the warning device shall conform to the requirement, as agreed between the manufacturer and the purchaser. 5.9 Resistance of printing If required, the permanence of print (or printing) on the warning device shall

49、be determined in accordance with 9.3 of EN 60898-1:2003 and shall fulfil the requirements specified in 9.3 of EN 60898-1:2003. 5.10 Marking The visual warning devices shall be marked at intervals not exceeding 1 m. The marking shall be legible when viewed without magnification, durable and shall include at least the following information: a) name or t