DIN 17753-2002 Wires of wrought nickel and nickel alloys - Properties《精制镍和镍合金线材 性能》.pdf

《DIN 17753-2002 Wires of wrought nickel and nickel alloys - Properties《精制镍和镍合金线材 性能》.pdf》由会员分享，可在线阅读，更多相关《DIN 17753-2002 Wires of wrought nickel and nickel alloys - Properties《精制镍和镍合金线材 性能》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、ICS 77.150.40Drhte aus Nickel und Nickelknetlegierungen EigenschaftenIn keeping with current practice in standards published by the International Organization for Standardization(ISO), a comma has been used throughout as the decimal marker.Ref. No. DIN 17753 : 2002-09English price group 06 Sales No.

2、 000603.03DEUTSCHE NORM September 200217753 No part of this translation may be reproduced without the prior permission ofDIN Deutsches Institut fr Normung e.V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).Translation by DIN-Sprac

3、hendienst.In case of doubt, the German-language original should be consulted as the authoritative text.Wrought nickel and nickel alloy wireRequirements and testingContinued on pages 2 to 6.SupersedesFebruary 1983 edition.ForewordThis standard has been prepared by the Normenausschuss Nichteisenmetall

4、e (Nonferrous Metals StandardsCommittee), Technical Committee Nickelwerkstoffe.See Other relevant standards for further standards covering requirements for nickel semi-finished products.AmendmentsThis standard differs from the February 1983 edition in that it has been revised in form and substance a

5、nd15 grades have been included.Previous editionsDIN 17753: 1973-12, 1983-02.1 ScopeThis standard specifies requirements for the mechanical properties of wrought nickel and nickel alloy wirehaving the dimensions specified in table 1, and gives details on the relevant methods of test.Where products ar

6、e to have dimensions other than those covered by this standard, this shall be subject toagreement.ContentsPage1 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Normative references . . . . . . . . . . . . . . . . . . . . . . .

7、. . . . . . . . . . . . . . . . . . . . 23 Ordering details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Mechanical properties at ambient temperature . . . . . . . . . . . . . . . . . . . . . . 25 Chemical composition . . . . . . . . . . . . . .

8、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Dimensions and tolerances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Other relevan

9、t standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Page 2DIN 17753 : 2002-092 Normative referencesThis standard incorporates, by dated or undated reference, provisions from other publications. These norma-tive references are cited at the appropriate pl

10、aces in the text and the titles of the publications are listed below.For dated references, subsequent amendments to or revisions of any of these publications apply to thisstandard only when incorporated in it by amendment or revision. For undated references, the latest edition ofthe publication refe

11、rred to applies.DIN 1333 Presentation of numerical dataDIN 17740 Wrought nickel Chemical compositionDIN 17741 Low-alloy wrought nickel alloys Chemical compositionDIN 17742 Wrought nickel-chromium alloys Chemical compositionDIN 17743 Wrought nickel-copper alloys Chemical compositionDIN 17744 Wrought

12、nickel-chromium-molybdenum alloys Chemical compositionDIN 59780 Hot rolled wrought nickel and nickel alloy round wire Dimensions and tolerancesDIN 59781 Drawn wrought nickel and nickel alloy round wire Dimensions and tolerancesDIN EN 10002-1 Metallic materials Tensile testing Method of test at ambie

13、nt temperature (includingCorrigendum AC 1 : 1990)3 Ordering detailsThe grade and the form of product supplied is at the purchasers discretion. It is recommended that the intendeduse of the product and any further processing be indicated at the time of ordering. For designating the product,the design

14、ation specified in the relevant dimensional standard shall be used.Any properties the products are to have shall be specified when ordering, together with the relevant testmethods.4 Mechanical properties at ambient temperatureThe products shall have the properties specified in table 1.5 Chemical com

15、positionThe chemical composition of wrought nickel and nickel alloy wire shall be as specified in the relevant standardsreferred to in table 1.6 Dimensions and tolerancesDimensions and tolerances for wrought nickel and nickel alloy wire shall be as specified in DIN 59780 orDIN 59781.7 TestingTensile

16、 strength, proof strength and percentage elongation after fracture shall be tested in accordance withDIN EN 10002-1.When expressing the result, rounding shall be in accordance with DIN 1333, to the same number of places asis given in table 1.Page 3DIN 17753 : 2002-09Table 1: Mechanical propertiesDes

17、ignationName NumberMaterialTemperHeattreatmentcondition1)Size,in mm2)From ToOverMin.tensilestrength,RmMin.percentageelongationafter fractureA5AL = 100(continued)Wrought nickel (with composition as in DIN 17740)Low-alloy wrought nickel alloys (with composition as in DIN 17741)Soft annealedSoft anneal

18、edSoft annealedSoft annealedHalf-hardHalf-hardHalf-hardHalf-hardHardHardHardHardSoft annealedSoft annealedSoft annealedSoft annealedHalf-hardHalf-hardHalf-hardHalf-hardSoft annealedSoft annealedSoft annealedSoft annealedHalf-hardHalf-hardHalf-hardHalf-hardHardHardHardHardSoft annealedSoft annealedSo

19、ft annealedSoft annealedHalf-hardHalf-hardHalf-hardHalf-hardSoft annealedSoft annealedSoft annealedSoft annealedSoft annealedSoft annealedSoft annealedSoft annealedPage 4DIN 17753 : 2002-09Table 1 (continued)DesignationName NumberMaterialTemperHeattreatmentcondition1)Size,in mm2)From ToOverMin.tensi

20、lestrength,RmMin.percentageelongationafter fractureA5AL = 100(continued)Soft annealedSoft annealedSoft annealedSoft annealedSoft annealedSoft annealedSoft annealedSoft annealedSoft annealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnneale

21、dAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedNickel-chromium alloys (with composition as in DIN 17742)Page 5DIN 17753 : 2002-09Table 1 (concluded)DesignationName NumberMaterialTemperHeattreatm

22、entcondition1)Size,in mm2)From ToOverMin.tensilestrength,RmMin.percentageelongationafter fractureA5AL = 100SoftSoftSoftSoftHalf-hardHalf-hardHalf-hardHalf-hardHardHardHardHardSoftSoftSoftSoftAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnea

23、ledAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedAnnealedNickel-copper alloys (with composition as in DIN 17743)Nickel-chromium-molybdenum alloys (with composition as in DIN 1774

24、4)1) Heat treatment condition as declared by manufacturer.2) Values refer to the diameter of round wire and to square, hexagonal and rectangular wire of the samecross section.Page 6DIN 17753 : 2002-09Other relevant standardsDIN 17745 Wrought nickel-iron alloys Chemical compositionDIN 17750 Wrought nickel and nickel alloy sheet, plate and strip Requirements and testingDIN 17751 Wrought nickel and nickel alloy pipes and tubes Requirements and testingDIN 17752 Wrought nickel and nickel alloy rod and bars Requirements and testing