DIN 1469-2012 Grooved pins half length grooved with gorge《半身长纹道带凹槽的插沟销》.pdf
《DIN 1469-2012 Grooved pins half length grooved with gorge《半身长纹道带凹槽的插沟销》.pdf》由会员分享,可在线阅读,更多相关《DIN 1469-2012 Grooved pins half length grooved with gorge《半身长纹道带凹槽的插沟销》.pdf(11页珍藏版)》请在麦多课文档分享上搜索。
1、 May 2012 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 21
2、.060.50!$|Z“1895561www.din.deDDIN 1469Grooved pins, half length grooved with gorgeEnglish translation of DIN 1469:2012-05Passkerbstifte mit HalsEnglische bersetzung von DIN 1469:2012-05Goupilles canneles gorgeTraduction anglaise de DIN 1469:2012-05SupersedesDIN 1469:2011-02www.beuth.deIn case of dou
3、bt, the German-language original shall be considered authoritative.Document comprises 11 pages05.12 DIN 1469:2012-05 2 A comma is used as the decimal marker. Contents Page Foreword . 3 1 Scope . 4 2 Normative references . 4 3 Dimensions 5 4 Masses . 8 5 Technical delivery conditions . 9 6 Designatio
4、n . 9 Annex A (informative) Examples of application 10 Bibliography . 11 DIN 1469:2012-05 3 Foreword This standard has been prepared by Working Committee NA 067-00-09 AA Verbindungselemente ohne Gewinde of the Normenausschuss Mechanische Verbindungselemente (Fasteners Standards Committee). Attention
5、 is drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN shall not be held responsible for identifying any or all such patent rights. Amendments This standard differs from DIN 1469:1978-11 as follows: a) normative references have been updated;
6、b) the standard has been editorially revised; c) Clause 4 “Technical delivery conditions” has been included; d) limit deviations for nominal dimension l have been specified. Compared with DIN 1469:2011-02 the following corrections have been made: a) in Table 2 and in item d) of the Amendments clause
7、, l2 has been changed to read l; b) in Tables 1 and 2 and in Clause 2, the normative reference to DIN EN ISO 286-2 has been corrected. Previous editions DIN 1469: 1966-09, 1978-11, 2011-02 DIN 1469:2012-05 4 1 Scope This standard applies to grooved pins, half-length grooved with gorge (press-fit fas
8、teners) used for holding retaining rings, retaining washers, springs, etc., the pin being seated firmly in a drilled hole of appropriate size. Such pins have a nominal diameter d1of 1,5 mm to 25 mm. A distinction is made between pins of type A (with slot for retaining rings as in DIN 471), type B (w
9、ith slot for retaining washers as in DIN 6799) and type C (with rounded slot). NOTE Tolerance class H11 is recommended for the hole into which the pin is to be inserted (see DIN EN ISO 8750). 2 Normative references The following referenced documents are indispensable for the application of this docu
10、ment. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. DIN 471, Retaining rings for shafts Normal type and heavy type DIN 6799, Retaining washers for shafts DIN EN 12476, Phosphate conversi
11、on coatings of metals Method of specifying requirements DIN EN ISO 3269, Fasteners Acceptance inspection DIN EN ISO 4042, Fasteners Electroplated coatings DIN EN ISO 8750, Spring-type straight pins Coiled, standard duty DIN EN ISO 286-2, Geometrical product specifications (GPS) ISO code system for t
12、olerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts DIN ISO 2768-1, General tolerances Tolerances for linear and angular dimensions without individual tolerance indications DIN ISO 8992, Fasteners General requirements for bolts, screws, st
13、uds and nuts DIN 1469:2012-05 5 3 Dimensions The dimensions of grooved pins shall be as specified in Figure 1, Table 1 and Table 2. Unless otherwise specified, general tolerances shall be class m tolerances as in ISO 2768-1. Commercial lengths of grooved pins are those given in the zone between the
14、stepped lines. Intermediate lengths are permitted but should be avoided if possible. aThe grooving angle 70 3 and the expanded diameter d2apply only to grooved pins made of free-cutting steel (St). Figure 1 Dimensions of grooved pin with gorge (notation) See Annex A for examples of application for t
15、he following pin types: type A with slot for retaining rings as in DIN 471; type B with slot for retaining washers as in DIN 6799; type C with rounded slot. DI N 1469: 2012 - 05 6 Ta bl e 1 D i m e ns i ons of groov e d pi n s w i t h gorge D ime n s i o n s i n mil l ime t r e s d1No m i n al siz e
16、 2 2,5 3 4 5 6 8 10 12 14 16 20 25 m a x. 2,0 2,5 3,0 4,0 5,0 6,0 8,0 10,0 12,0 14,0 16,0 20,0 25,0 m i n. 1,975 2,475 2,975 3,925 4,925 5,925 7,910 9,910 11,890 13,890 15,890 19,870 24,870 ( per m . dev . ) h9 h11 d2per m . dev . + 0,050 0,05 0,1 a + 1 0 0,7 1,0 1,0 1,4 1,5 2,0 2,0 2,5 2,5 2,5 2,5
17、3,0 3,0 c 0,25 0,3 0 0, 4 0 0,5 0 0,6 0 0,8 0 1 ,00 1,2 0 1,6 0 1,6 0 2 ,00 2,5 0 3 ,00 T yp e A gbm a x. 2,8 3,8 4,8 5,7 7,6 9,6 11,5 13,4 15,2 19 ,0 23,9 m i n. 2,740 3,725 4,725 5,625 7,510 9,510 11,390 13,290 15,090 18,870 23,770 mcm a x. 0,64 0,64 0,84 0,94 1,04 1,24 1,24 1,24 1,24 1,44 1,44 m
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DIN14692012GROOVEDPINSHALFLENGTHGROOVEDWITHGORGE 半身 长纹道带 凹槽 插沟销 PDF

链接地址:http://www.mydoc123.com/p-653236.html