BS ISO 702-3-2007 Machine tools - Connecting dimensions of spindle noses and work holding chucks - Bayonet type《机床 主轴头和工件卡盘的连接尺寸规格 卡口型》.pdf

《BS ISO 702-3-2007 Machine tools - Connecting dimensions of spindle noses and work holding chucks - Bayonet type《机床 主轴头和工件卡盘的连接尺寸规格 卡口型》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 702-3-2007 Machine tools - Connecting dimensions of spindle noses and work holding chucks - Bayonet type《机床 主轴头和工件卡盘的连接尺寸规格 卡口型》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS ISO 702-3:2007Machine tools Connecting dimensions of spindle noses and work holding chucks Part 3: Bayonet typeICS 25.060.20g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37

2、g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS ISO 702-3:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2007 BSI 2007ISBN 978 0 580 55952 5National forewordThis British Standard is the UK implementation of ISO 702-3:2007.The U

3、K participation in its preparation was entrusted to Technical Committee MTE/1, Machine tools.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsibl

4、e for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsReference numberISO 702-3:2007(E)INTERNATIONAL STANDARD ISO702-3Second edition2007-10-15Machine tools Connecting dimensions of spind

5、le noses and work holding chucks Part 3: Bayonet type Machines-outils Dimensions dassemblage des nez de broches et des mandrins porte-pices Partie 3: Type baonnette BS ISO 702-3:2007ii iiiContents Page Foreword iv 1 Scope . 1 2 Interchangeability . 1 3 Sizes for interchangeability . 2 3.1 Spindle no

6、ses 2 3.2 Bayonet disc 4 3.3 Face plates 6 3.4 Studs with nuts and collars . 8 Bibliography . 10 BS ISO 702-3:2007iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Stand

7、ards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also ta

8、ke part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees i

9、s to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibili

10、ty that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 702-3 was prepared by Technical Committee ISO/TC 39, Machine tools, Subcommittee SC 8, Work holding spindles and chucks. This second

11、 cancels and replaces the first edition (ISO 702-3:1975), of which all the clauses, tables and figures have been technically revised. ISO 702 consists of the following parts, under the general title Machine tools Connecting dimensions of spindle noses and work holding chucks: Part 1: Conical connect

12、ion Part 2: Camlock type Part 3: Bayonet type Part 4: Cylindrical connection BS ISO 702-3:20071Machine tools Connecting dimensions of spindle noses and work holding chucks Part 3: Bayonet type 1 Scope This part of ISO 702 specifies the sizes for interchangeability of bayonet-type lathe spindle noses

13、 and corresponding face plates. NOTE The “conical connection”, “camlock type” and “cylindrical connection” are dealt with in ISO 702-1, ISO 702-2 and ISO 702-4, respectively. 2 Interchangeability In this part of ISO 702, all the dimensions and tolerances are expressed in millimetres. BS ISO 702-3:20

14、072 3 Sizes for interchangeability 3.1 Spindle noses Key 1 size Nos. 3 and 4, No. 3 without button 2 size Nos. 5 to 8 3 size Nos. 11 to 20 aAll holes. Figure 1 Spindle noses BS ISO 702-3:20073Table 1 Dimensions of spindle noses Size No. Dimension 3 4 5 6 8 11 15 20 nom. 53,975 63,513 82,563 106,375

15、139,719 196,869 285,775 412,775 d1 tol. +0,008 0 +0,008 0 +0,010 0 +0,010 0 +0,012 0 +0,014 0 +0,016 0 +0,020 0 d275 85 104,8 133,4 171,4 235 330,2 463,6 d3102 112 135 170 220 290 400 540 d421 21 21 23 29 36 43 43 d5 H8/h8 14,25 15,9 19,05 23,8 28,6 34,9 41,3 d66,4 6,4 6,4 8,4 10,5 10,5 13 13 d710,4

16、 10,4 10,4 13,5 16,5 16,5 19 19 e 11 11 13 14 16 18 19 21 f 16 20 22 25 28 35 42 48 g 5 5 5 6 8 8 8 h 10 10 10 11 12 13 15 15 w 0,2 0,2 0,2 0,2 0,2 0,2 0,3 0,3 NOTE General tolerance for untoleranced dimensions: 0,4 mm. BS ISO 702-3:20074 3.2 Bayonet disc Key 1 size Nos. 3 and 4 2 size Nos. 5 to 8 3

17、 size Nos. 11 to 20 4 thrust socket 5 hexagon-socket head screw aAll holes. Figure 2 Bayonet disc BS ISO 702-3:20075Table 2 Dimensions of bayonet disc Size No. Dimension 3 4 5 6 8 11 15 20 d175 85 104,8 133,4 171,4 235 330,2 463,6 d250 60 80 100 130 185 270 400 d3110 120 145 180 230 300 410 550 d421

18、 21 21 23 29 36 43 43 d5 M6 M6 M6 M8 M10 M10 M12 M12 d6 11 11 11 13 17 17 22 22 d716 16 16 19 25 25 32 32 e 11,5 11,5 11,5 14 18 23 27 27 f 11,5 11,5 11,5 14 18 18 23 23 g0 0,1 5 6 8 10 12 16 18 22 h 8 9 12 15 18 22 26 30 h1 +0,2 0 5,2 6,2 8,2 10,2 12,2 16,2 18,3 22,3 s 0 0,2 14 14 14 17 22 22 27 27

19、 w 0,2 0,2 0,2 0,2 0,2 0,2 0,3 0,3 Hexagon-socket head screw M6 15 M6 20 M6 25 M8 30 M10 35 M10 45 M12 55 M12 65 NOTE General tolerance for untoleranced dimensions: 0,4 mm. BS ISO 702-3:20076 3.3 Face plates Figure 3 Face plates BS ISO 702-3:20077Table 3 Dimensions of face plates Size No. Dimension

20、3 4 5 6 8 11 15 20 d1 nom. 53,975 63,513 82,563 106,375 139,719 196,869 285,775 412,775 tol. Type 1a+0,003 0,005 +0,003 0,005 +0,004 0,006 +0,004 0,006 +0,004 0,008 +0,004 0,010 +0,004 0,012 +0,005 0,015 tol. Type 2 a+0,008 0 +0,008 0 +0,010 0 +0,010 0 +0,012 0 +0,014 0 +0,016 0 +0,020 0 d275 85 104

21、,8 133,4 171,4 235 330,2 463,6 d351,5 61 79,6 103,2 136,2 192,9 281,5 408 d4102 112 135 170 220 290 400 540 d5M10 M10 M10 M12 M16 M20 M24 M24 d6 +0,1 0 14,7 16,3 19,45 24,25 29,4 35,7 42,1 d7 11 11 11 14 18 22 26 26 e 10 10 12 13 14 16 17 19 f 15 15 15 18 24 30 36 36 g 18 18 18 22 28 34 40 40 h 6,5

22、6,5 6,5 8 10 10 10 w 0,2 0,2 0,2 0,2 0,2 0,2 0,3 0,3 Stud M10 34 M10 39 M10 43 M12 50 M16 60 M20 75 M24 90 M24 100 NOTE General tolerance for untoleranced dimensions: 0,4 mm. aType identification shall be marked. BS ISO 702-3:20078 3.4 Studs with nuts and collars Key 1 stud 2 nut with collars Figure

23、 4 Stud bolt with collar nut BS ISO 702-3:20079Table 4 Dimensions of studs with nuts and collars Size No. Dimension 3 4 5 6 8 11 15 20 d1M10 M10 M10 M12 M16 M20 M24 M24 d2 h11 19,5 19,5 19,5 21,5 27 34 41 41 d3 7,7 7,7 7,7 9,4 13 16,4 19,6 19,6 h112 12 12 14 18 22 27 27 h23 3 3 3 3 4 4 4 l134 39 43

24、50 60 75 90 100 l220 22 24 28 35 44 52 56 l318 18 18 20 25 30 36 36 l412 12 12 15 20 25 30 30 l55 8 10 12 12 15 20 26 r 0,6 0,6 0,6 1 1 1 1,6 1,6 s 17 17 17 19 24 30 36 36 NOTE General tolerance for untoleranced dimensions: 0,4 mm. BS ISO 702-3:200710 Bibliography 1 ISO 702-1, Machine tools Connecti

25、ng dimensions of spindle noses and work holding chucks Part 1: Conical connection 2 ISO 702-2, Machine tools Connecting dimensions of spindle noses and work holding chucks Part 2: Camlock type 3 ISO 702-4, Machine tools Connecting dimensions of spindle noses and work holding chucks Par 4: Cylindrica

26、l connection BS ISO 702-3:2007blankBS ISO 702-3:2007BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporate

27、d by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone findin

28、g an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called

29、PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards a

30、re also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of inform

31、ation on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax:

32、+44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 89

33、96 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyrigh

34、t, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise

35、without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.