BS ISO 702-2-2007 Machine tools - Connecting dimensions of spindle noses and work holding chucks - Camlock type《机床 主轴头和工件卡盘的连接尺寸规格 凸轮锁紧型》.pdf

《BS ISO 702-2-2007 Machine tools - Connecting dimensions of spindle noses and work holding chucks - Camlock type《机床 主轴头和工件卡盘的连接尺寸规格 凸轮锁紧型》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 702-2-2007 Machine tools - Connecting dimensions of spindle noses and work holding chucks - Camlock type《机床 主轴头和工件卡盘的连接尺寸规格 凸轮锁紧型》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS ISO 702-2:2007Machine tools Connecting dimensions of spindle noses and work holding chucks Part 2: Camlock typeICS 25.060.20g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37

2、g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Incorporating October 2009corrigendum National forewordThis British Standard is the UK implementation of ISO 702-2:2007, incorporating corrigendum October 2009. The UK participation in its preparation was entrusted to Technical Committee MTE/1, Machine tool

3、s. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity

4、from legal obligations.BS ISO 702-2:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2007 BSI 2010 Amendments/corrigenda issued since publicationDate Comments 28 February 2010 Implementation of ISO corrigendum October 2009, igu

5、re 2 repl ced and Tables 1 and 8 modifiedISBN 978 0 580 69577 3F aReference numberISO 702-2:2007(E)INTERNATIONAL STANDARD ISO702-2Second edition2007-10-15Machine tools Connecting dimensions of spindle noses and work holding chucks Part 2: Camlock type Machines-outils Dimensions dassemblage des nez d

6、e broches et des mandrins porte-pices Partie 2: Type Camlock BS ISO 702-2:2007ii iiiContents Page Foreword iv 1 Scope . 1 2 Interchangeability . 1 3 Sizes for interchangeability . 2 3.1 Spindle noses 2 3.2 Cams 4 3.3 Studs 6 3.4 Face plates 8 3.5 Accessories for spindle noses and face plates. 9 Bibl

7、iography . 11 BS ISO 702-2:2007iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body int

8、erested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnic

9、al Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the

10、technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.

11、ISO shall not be held responsible for identifying any or all such patent rights. ISO 702-2 was prepared by Technical Committee ISO/TC 39, Machine tools, Subcommittee SC 8, Work holding spindles and chucks. This second edition cancels and replaces the first edition (ISO 702-2:1975), of which all the

12、clauses, tables and figures have been technically revised. ISO 702 consists of the following parts, under the general title Machine tools Connecting dimensions of spindle noses and work holding chucks: Part 1: Conical connection Part 2: Camlock type Part 3: Bayonet type Part 4: Cylindrical connectio

13、n BS ISO 702-2:20071Machine tools Connecting dimensions of spindle noses and work holding chucks Part 2: Camlock type 1 Scope This part of ISO 702 specifies the sizes for interchangeability of cylindrical spindle noses and corresponding connecting faces of face plates or work holding chucks. NOTE Th

14、e “conical connection”, “bayonet type” and “cylindrical connection” are dealt with in ISO 702-1, ISO 702-3 and ISO 702-4, respectively. 2 Interchangeability In this part of ISO 702, all the dimensions and tolerances are expressed in millimetres. Although internal mounting components and assembly scr

15、ews are not respectively interchangeable, as they may conform with either the metric or inch series, there is complete interchangeability between metric spindle noses and face plates in inches and vice versa. BS ISO 702-2:20072 3 Sizes for interchangeability 3.1 Spindle noses Key 1 size No. 3 2 size

16、 No. 4 3 size Nos. 5 to 20 aReference line. Figure 1 Spindle noses BS ISO 702-2:20073Table 1 Dimensions of spindle noses Size No. Dimension 3 4 5 6 8 11 15 20 nom. 53,975 63,513 82,563 106,375 139,719 196,869 285,775 412,775 d1 tol. +0,008 0 +0,008 0 +0,010 0 +0,010 0 +0,012 0 +0,014 0 +0,016 0 +0,0

17、20 0 d265 82 114 172 258 380 d370,6 82,6 104,8 133,4 171,4 235,0 330,2 463,6 d492 117 146 181 225 298 403 546 d5 +0,05 0 15,1 16,7 19,8 23,0 26,2 31,0 35,7 42,1 d6H8 19 19 22 26 29 32 35 42 d7M8 M8 M6 M8 M8 M8 M10 M10 d815,5 15,5 10,5 13,5 13,5 13,5 16,5 16,5 e 11 11 13 14 16 18 19 21 f min. 32 34 3

18、8 45 50 60 70 82 g 0,05 22,6 27,0 h 0,2 30 40 j 17,5 17,5 20,6 23,8 27,0 31,8 36,5 42,9 k 0,1 11,1 11,1 13,5 15,9 18,25 21,45 24,6 28,6 l+0,2 0 27,5 36 46 57 64 75 84 94 m 7 9 9 9 11 11 w 0,1 0,15 0,15 0,15 0,15 0,15 0,15 0,15 x 0,2 0,2 0,2 0,2 0,2 0,2 0,2 0,2 18 18,6 15 36 14 55 13 46 12 18 10 30 8

19、 35 7 05 NOTE General tolerance for untoleranced dimensions: 0,4 mm. BS ISO 702-2:20074 BS ISO 702-2:20073.2 Cams aReference line. Figure 2 Cams 5Table 2 Dimensions of cams Size No. Dimension 3 4 5 6 8 11 15 20 a min. 13 17 22 25 28 32 37 43 b0 0,2 13,4 11,9 14,2 16,7 18,9 21,2 23,5 27,8 c 7 10 10 1

20、0 10 10 d+0,3 0 1,65 1,60 1,45 2,56 2,46 2,44 2,35 3,10 e+0,1 0 0,15 0,15 0 0,45 0,36 0,28 0,20 0,50 h0 0,1 26,5 35 45 56 63 73 82 92 i 0,1 2,2 2,2 3,0 4,2 5,3 8,7 6,0 6,0 j 3,6 0,05 3,6 0,05 5,0 0,1 6,5 0,1 6,5 0,1 6,5 0,1 8,5 0,1 8,5 0,1 k e8 19 19 22 26 29 32 35 42 l 13 0,2 13 0,2 14 17 21 24 27

21、33 m 0,05 4,5 6 6 6 8 8 n 0,1 2,0 2,85 3,95 7,35 5,2 5,2 o 0,2 14,9 16,7 22,4 30,2 33,2 39,5 43,6 48,4 p 21,4 26,5 35,0 43,0 49,0 59,0 62,0 69,0 q D12 8 10 11 12 14 17 17 22 r 7,5 9,5 11,1 12,7 14,2 16,7 19,0 22,2 s 13 15 15 15 15 15 t 8 9 11 12 14 16 16 20 u 1,2 1,2 Slope on v a1,60 1,90 1,90 2,64

22、2,64 2,64 2,64 3,18 15 10 10 10 10 15 15 15 15 15 15 20 20 20 20 20 NOTE General tolerance for untoleranced dimensions: 0,4 mm. aSee tolerance on dimensions d and e. BS ISO 702-2:20076 3.3 Studs Dimensions in millimetres Key 1 size Nos. 4 to 20 2 size No. 3 aCircular reference line for setting posit

23、ion of stud. Figure 3 Studs BS ISO 702-2:20077Table 3 Dimensions of studs Size No. Dimension 3 4 5 6 8 11 15 20 a 0,1 12,7 13,5 16,5 19,6 23,2 26,8 32,0 38,5 b 0,2 4,2 4,8 4,8 4,8 4,8 6,4 6,4 6,4 c0 0,1 14,3 15,9 19,0 22,2 25,4 30,2 34,9 41,3 d M10 1 M10 1 M12 1 M16 1,5 M20 1,5 M22 1,5 M24 1,5 M27 2

24、 e 0,1 8,7 9,5 11,9 14,3 16,7 20,6 24,6 28,6 g 35 37 43 49 55,5 67 76 89 h 19 19 22 27 30,5 35 40 44 k 11 11 11 14 14 14 14 14 l 0,2 30,0 31,0 35,7 40,5 44,5 53,2 58,7 69,0 r 9,5 9,5 11,25 12,7 14,3 15,9 17,5 20,6 NOTE General tolerance for untoleranced dimensions: 0,4 mm. BS ISO 702-2:20078 3.4 Fac

25、e plates Key 1 size Nos. 3 and 4 2 size Nos. 5 to 20 aReference line. Figure 4 Face plates BS ISO 702-2:20079Table 4 Dimensions of face plates Size No. Dimension 3 4 5 6 8 11 15 20 d153,975 63,513 82,563 106,375 139,719 196,869 285,775 412,775 tol. Type 1 a+0,003 0,005 +0,003 0,005 +0,004 0,006 +0,0

26、04 0,006 +0,004 0,008 +0,004 0,010 +0,004 0,012 +0,005 0,015 tol. Type 2 a +0,008 0 +0,008 0 +0,010 0 +0,010 0 +0,012 0 +0,014 0 +0,016 0 +0,020 0 d270,6 82,6 104,8 133,4 171,4 235,0 330,2 463,6 d392 117 146 181 225 298 403 546 d4M10 1 M10 1 M12 1 M16 1,5 M20 1,5 M22 1,5 M24 1,5 M27 2 d514,6 16,2 19

27、,4 22,6 25,8 30,6 35,4 41,6 d6M6 M6 M6 M8 M8 M8 M8 M8 d710,5 10,5 10,5 13,5 13,5 13,5 13,5 13,5 f min. 13 13 15 16 18 20 21 23 g 10 10 12 13 14 16 17 19 h 26 28 30 35 38 45 50 55 j 7 8 8 9,5 9,5 13 13 13 l 11,0 11,0 12,5 15,5 17,5 18,7 21,5 24,8 m 7 7 7 9 9 9 9 9 w 0,1 0,15 0,2 0,2 0,2 0,2 0,2 0,2 x

28、 0,2 0,2 0,2 0,2 0,2 0,2 0,2 0,2 18 18,6 15 36 14 55 13 46 12 18 10 30 8 35 7 05 NOTE General tolerance for untoleranced dimensions: 0,4 mm. aThe type identification shall be marked. 3.5 Accessories for spindle noses and face plates 3.5.1 Hexagon-socket head screw for studs Table 5 Dimension of hexa

29、gon-socket head screw for studs Size No. Dimension 3 4 5 6 8 11 15 20 d M6 M6 M6 M8 M8 M8 M8 M8 d110 10 10 13 13 13 13 13 k 6 6 6 8 8 8 8 8 l 12 12 12 14 14 14 14 14 BS ISO 702-2:200710 3.5.2 Hexagon-socket head screw for cams Table 6 Dimension of hexagon-socket head screw for cams Size No. Dimensio

30、n 3 4 5 6 8 11 15 20 d M6 M8 M8 M8 M10 M10 d110 13 13 13 16 16 d2max. 4,5 6 6 6 8 8 k 6 8 8 8 10 10 l 19 20 23 28 30 35 l14 5 5 5 5 5 3.5.3 Stop-bolt for cams Table 7 Dimension of stop-bolt for cams Size No. Dimension 3 4 5 6 8 11 15 20 b 0 0,05 3,5 3,5 c 0,8 0,8 d 6,3 6,3 l 0 0,2 14,4 14,4 l14,8 4,

31、8 3.5.4 Cheese head screw for cams Table 8 Dimension of cheese head screw for cams Size No. Dimension3 4 5 6 8 11 15 20 d M8 M8 d1 max. 15 15 k max. 5,6 5,6 l 0,2 8 18 BS ISO 702-2:200711Bibliography 1 ISO 702-1, Machine tools Connecting dimensions of spindle noses and work holding chucks Part 1: Co

32、nical connection 2 ISO 702-3, Machine tools Connecting dimensions of spindle noses and work holding chucks Part 2: Bayonet type 3 ISO 702-4, Machine tools Connecting dimensions of spindle noses and work holding chucks Part 4: Cylindrical connection BS ISO 702-2:2007BSI GroupHeadquarters 389 Chiswick

33、 High Road, London, W4 4AL, UK Tel +44 (0)20 8996 9001 Fax +44 (0)20 8996 7001 standardsBSI - British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorpora

34、ted by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone find

35、ing an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service calle

36、d PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001 Email: You may also buy dire

37、ctly using a debit/credit card from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide rang

38、e of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact Information Centre. Tel: +44 (0)20 8996 7111

39、 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 70

40、01 Email: Information regarding online access to British Standards via British Standards Online can be found at http:/ information about BSI is available on the BSI website at http:/ CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of

41、the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from

42、 BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager. Tel: +44 (0)20 8996 7070 Email: BS ISO 702-2:2007