BS ISO 5446-2017 Ferromanganese Specification and conditions of delivery《锰铁 交货规格和条件》.pdf

《BS ISO 5446-2017 Ferromanganese Specification and conditions of delivery《锰铁 交货规格和条件》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 5446-2017 Ferromanganese Specification and conditions of delivery《锰铁 交货规格和条件》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、Ferromanganese Specification and conditions of deliveryBS ISO 5446:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06 ISO 2017Ferromanganese SpecificationandconditionsofdeliveryFerro-manganse Spcifications et conditions de livraisonINTERNATIONALSTANDARDISO5446Secon

2、d edition2017-07Reference numberISO 5446:2017(E)National forewordThis British Standard is the UK implementation of ISO 5446:2017. The UK participation in its preparation was entrusted to Technical Committee ISE/102, Methods of Chemical Analysis for Iron and Steel.A list of organizations represented

3、on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 86249

4、 6ICS 77.100Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS

5、ISO 5446:2017 ISO 2017Ferromanganese Specification and conditions of deliveryFerro-manganse Spcifications et conditions de livraisonINTERNATIONAL STANDARDISO5446Second edition2017-07Reference numberISO 5446:2017(E)BS ISO 5446:2017ISO 5446:2017(E)ii ISO 2017 All rights reservedCOPYRIGHT PROTECTED DOC

6、UMENT ISO 2017, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written

7、 permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 5446:2017ISO

8、5446:2017(E)ii ISO 2017 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying

9、, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11F

10、ax +41 22 749 09 47copyrightiso.orgwww.iso.orgISO 5446:2017(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Information for ordering . 15 Requirements 15.1 Constitution of consignment . 15.2 Chemical composition 25.3 Particle size ranges 25.4 Extraneous contamination . 2

11、6 Testing . 26.1 General . 26.2 Sampling for chemical analysis and sieve analysis 26.3 Analysis 36.4 Contradictory analysis 36.5 Arbitral analysis . 37 Dispatch and storage 4Annex A (informative) Arbitral analysis . 7Bibliography 9 ISO 2017 All rights reserved iiiContents PageBS ISO 5446:2017ISO 544

12、6:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for w

13、hich a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all

14、 matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. Thi

15、s document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any

16、or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of u

17、sers and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barri

18、ers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.This document was prepared by Technical Committee ISO/TC 132, Ferroalloys.This second edition cancels and replaces the first edition (ISO 5446:1980), which has been technically revised to update the chemical composition and

19、 the particle size of ferromanganese.iv ISO 2017 All rights reservedBS ISO 5446:2017ISO 5446:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally c

20、arried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the wor

21、k. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the diffe

22、rent approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).Attention is drawn to the possibility that some of the elements of this document

23、may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/

24、patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information a

25、bout ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.This document was prepared by Technical Committee ISO/TC 132, Ferroalloys.This second edition cancels and replaces the first edition

26、 (ISO 5446:1980), which has been technically revised to update the chemical composition and the particle size of ferromanganese.iv ISO 2017 All rights reserved INTERNATIONAL STANDARD ISO 5446:2017(E)Ferromanganese Specification and conditions of delivery1 ScopeThis document specifies requirements an

27、d conditions of delivery for ferromanganese usually supplied for steelmaking and foundry use.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cit

28、ed applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 4552-1, Ferroalloys Sampling and sample preparation for chemical analysis Part 1: Ferrochromium, ferrosilicochromium, ferrosilicon, ferrosilicomanganese, ferromanganeseISO 8954-1,

29、 Ferroalloys Vocabulary Part 1: Materials3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 8954-1 apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at h t t p :/ www .e

30、lectropedia .org/ ISO Online browsing platform: available at h t t p :/ www .iso .org/ obp4 Information for orderingOrders for ferromanganese shall include the following information:a) quantity;b) constitution of consignment;c) chemical composition in accordance with the designations given in Tables

31、 1 to 6;d) particle size ranges in accordance with the classes given in Table 7;e) necessary requirements for analysis reports packing, etc., as appropriate.5 Requirements5.1 Constitution of consignmentA consignment of a ferromanganese may consist of one or more lots or parts of a lot, which are def

32、ined in ISO 8954-1. In one consignment, one of the following types of lots may be used:a) tapped lot;b) graded lot; ISO 2017 All rights reserved 1BS ISO 5446:2017ISO 5446:2017(E)c) blended lot.5.2 Chemical composition5.2.1 The chemical composition of ferromanganese shall be as specified in Tables 1

33、to 6. The limits stated correspond to particle size ranges in Tables 1 to 6 in accordance with Table 7.5.2.2 Special requirements, such as special ranges for the specified elements, or other requirements for unspecified elements, should be agreed upon between the purchaser and the supplier.5.2.3 The

34、 content of manganese, which is given in Tables 1 to 6, corresponds to the precision of sampling and analysis for ferromanganese (see Clause 6).For other elements, the number of significant digits is set, taking into account the existing methods of analysis and may be agreed upon between the supplie

35、r and the purchaser.5.3 Particle size ranges5.3.1 Ferromanganese is supplied in lumps or as crushed and screened particles. The particle size ranges and tolerances shall be in accordance with Table 7. The undersize values shall be valid at the point of delivery to the purchaser.The particle sizes sp

36、ecified refer to screening on a steel sieve with square openings; see ISO 565.5.3.2 If the purchaser requires particle size ranges and/or tolerances other than those given in Table 7, those shall be agreed upon between the supplier and the purchaser.5.4 Extraneous contaminationThe material shall be

37、as free as possible from extraneous contamination.6 Testing6.1 General6.1.1 The supplier shall establish and supply with the ferromanganese an analysis certificate for the manganese content and, if agreed with the purchaser, for the contents of the other elements either specified in Tables 1 to 6 or

38、 additionally agreed. Upon the request of the purchaser, a sample representative of the consignment shall also be provided.6.1.2 If necessary, the purchaser may conduct routine tests of the chemical and granulometric composition of the party. The following two options can be used when controlling th

39、e chemical composition:a) carry out the analysis of samples provided by the supplier along with the consignment;b) conduct independent sampling of consignment.6.2 Sampling for chemical analysis and sieve analysis6.2.1 Sampling for chemical analysis and sieve analysis should be carried out by the met

40、hods specified in ISO 3713, ISO 4551 and ISO 4552-1, but other methods of sampling having similar precision may also be used.2 ISO 2017 All rights reservedBS ISO 5446:2017ISO 5446:2017(E)c) blended lot.5.2 Chemical composition5.2.1 The chemical composition of ferromanganese shall be as specified in

41、Tables 1 to 6. The limits stated correspond to particle size ranges in Tables 1 to 6 in accordance with Table 7.5.2.2 Special requirements, such as special ranges for the specified elements, or other requirements for unspecified elements, should be agreed upon between the purchaser and the supplier.

42、5.2.3 The content of manganese, which is given in Tables 1 to 6, corresponds to the precision of sampling and analysis for ferromanganese (see Clause 6).For other elements, the number of significant digits is set, taking into account the existing methods of analysis and may be agreed upon between th

43、e supplier and the purchaser.5.3 Particle size ranges5.3.1 Ferromanganese is supplied in lumps or as crushed and screened particles. The particle size ranges and tolerances shall be in accordance with Table 7. The undersize values shall be valid at the point of delivery to the purchaser.The particle

44、 sizes specified refer to screening on a steel sieve with square openings; see ISO 565.5.3.2 If the purchaser requires particle size ranges and/or tolerances other than those given in Table 7, those shall be agreed upon between the supplier and the purchaser.5.4 Extraneous contaminationThe material

45、shall be as free as possible from extraneous contamination.6 Testing6.1 General6.1.1 The supplier shall establish and supply with the ferromanganese an analysis certificate for the manganese content and, if agreed with the purchaser, for the contents of the other elements either specified in Tables

46、1 to 6 or additionally agreed. Upon the request of the purchaser, a sample representative of the consignment shall also be provided.6.1.2 If necessary, the purchaser may conduct routine tests of the chemical and granulometric composition of the party. The following two options can be used when contr

47、olling the chemical composition:a) carry out the analysis of samples provided by the supplier along with the consignment;b) conduct independent sampling of consignment.6.2 Sampling for chemical analysis and sieve analysis6.2.1 Sampling for chemical analysis and sieve analysis should be carried out b

48、y the methods specified in ISO 3713, ISO 4551 and ISO 4552-1, but other methods of sampling having similar precision may also be used.2 ISO 2017 All rights reserved ISO 5446:2017(E)6.2.2 Sampling is usually carried out at the suppliers stockyard, unless otherwise agreed. Wherever sampling is carried

49、 out, representatives of both the supplier and the purchaser may be present.6.2.3 If required, arbitration sampling shall be carried out by an arbitrator chosen by mutual agreement between the supplier and the purchaser. Sampling should be carried out by the method specified in ISO 3713, ISO 4551 and ISO 4552-1, but other methods of sampling having similar precision may be agreed upon between the supplier, the purchaser and the arbitrator.The sample obtained by arbitration shall be accepted by both parties.6.3 Analysis