BS ISO 21009-1-2008 Cryogenic vessels - Static vacuum-insulated vessels - Design fabrication inspection and tests《低温容器 静压真空绝缘容器 设计、制造、检验和试验》.pdf

《BS ISO 21009-1-2008 Cryogenic vessels - Static vacuum-insulated vessels - Design fabrication inspection and tests《低温容器 静压真空绝缘容器 设计、制造、检验和试验》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 21009-1-2008 Cryogenic vessels - Static vacuum-insulated vessels - Design fabrication inspection and tests《低温容器 静压真空绝缘容器 设计、制造、检验和试验》.pdf（136页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO21009-1:2008ICS 23.020.40NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDCryogenic vessels Static vacuum-insulated vesselsPart 1: Design, fabrication, inspectionand testsThis British Standardwas published under the authority of theStandards Policy andStrat

2、egy Committee on 31 BSI 2008ISBN 978 0 580 57349 1Amendments/corrigenda issued since publicationDate CommentsBS ISO 21009-1:2008National forewordThis British Standard is the UK implementation of ISO 21009-1:2008.The UK participation in its preparation was entrusted to TechnicalCommittee PVE/18, Cryo

3、genic vessels.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer im

4、munityfrom legal obligations.October 2008BS ISO 21009-1:2008Reference numberISO 21009-1:2008(E)ISO 2008INTERNATIONAL STANDARD ISO21009-1First edition2008-09-01Cryogenic vessels Static vacuum-insulated vessels Part 1: Design, fabrication, inspection and tests Rcipients cryogniques Rcipients isols sou

5、s vide statiques Partie 1: Exigences de conception de fabrication, dinspection, et dessais BS ISO 21009-1:2008ISO 21009-1:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless

6、 the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark o

7、f Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In t

8、he unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, el

9、ectronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightis

10、o.org Web www.iso.org Published in Switzerland ii ISO 2008 All rights reservedBS ISO 21009-1:2008ISO 21009-1:2008(E) ISO 2008 All rights reserved iiiContents Page Foreword. v 1 Scope 1 2 Normative references 1 3 Terms and definitions .2 4 Symbols 5 5 General requirements7 6 Mechanical loads .7 6.1 G

11、eneral7 6.2 Load during the pressure test7 7 Chemical effects 8 8 Thermal conditions8 9 Material .8 9.1 Selection of materials8 9.2 Inspection certificate.9 9.3 Materials for outer jackets and service equipment9 10 Design .9 10.1 Design options.9 10.2 Common design requirements.9 10.3 Design by calc

12、ulation16 11 Fabrication43 11.1 General43 11.2 Cutting 43 11.3 Cold forming.47 11.4 Hot forming.49 11.5 Manufacturing tolerances .50 11.6 Welding .53 11.7 Non-welded permanent joints 54 12 Inspection and testing.54 12.1 Quality plan 54 12.2 Production control test plates56 12.3 Non-destructive testi

13、ng.57 12.4 Rectification .60 12.5 Pressure testing.60 13 Marking and labelling 61 14 Final assessment.62 15 Periodic inspection62 Annex A (normative) Elastic stress analysis 63 Annex B (normative) Additional requirements for 9 % Ni steel 72 Annex C (normative) Pressure strengthening of vessels from

14、austenitic stainless steels 74 Annex D (informative) Pressure limiting systems .85 Annex E (normative) Further use of the material cold properties to resist pressure loads86 Annex F (informative) Specific weld details .90 BS ISO 21009-1:2008ISO 21009-1:2008(E) iv ISO 2008 All rights reservedAnnex G

15、(normative) Additional requirements for flammable fluids 94 Annex H (informative) Relief devices 95 Annex I (normative) Outer jacket relief devices 96 Annex J (informative) Increased material property for austenitic stainless steel . 97 Annex K (normative) Base materials 98 Annex L (normative) Cylin

16、drical shells subject to external pressure (pressure on the convex surface) Calculation . 107 Annex M (normative) Design of openings in cylinders, spheres and cones Calculation 112 Annex N (normative) Design of ends for internal pressure . 122 Bibliography . 124 BS ISO 21009-1:2008ISO 21009-1:2008(E

17、) ISO 2008 All rights reserved vForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body inter

18、ested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical

19、 Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the te

20、chnical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IS

21、O shall not be held responsible for identifying any or all such patent rights. ISO 21009-1 was prepared by Technical Committee ISO/TC 220, Cryogenic vessels. ISO 21009 consists of the following parts, under the general title Cryogenic vessels Static vacuum-insulated vessels: Part 1: Design, fabricat

22、ion, inspection and tests Part 2: Operational requirements: BS ISO 21009-1:2008BS ISO 21009-1:2008INTERNATIONAL STANDARD ISO 21009-1:2008(E) ISO 2008 All rights reserved 1Cryogenic vessels Static vacuum-insulated vessels Part 1: Design, fabrication, inspection and tests 1 Scope This part of ISO 2100

23、9 specifies requirements for the design, fabrication, inspection and testing of static vacuum-insulated cryogenic vessels designed for a maximum allowable pressure of more than 0,5 bar. This part of ISO 21009 applies to static vacuum-insulated cryogenic vessels for fluids as specified in 3.4 and doe

24、s not apply to vessels designed for toxic fluids. For static vacuum-insulated cryogenic vessels designed for a maximum allowable pressure of not more than 0,5 bar this International Standard may be used as a guide. 2 Normative references The following referenced documents are indispensable for the a

25、pplication of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 4126-2, Safety devices for protection against excessive pressure Part 2: Bursting disc safety devices ISO 4

26、136, Destructive tests on welds in metallic materials Transverse tensile test ISO 9016, Destructive tests on welds in metallic materials Impact tests Test specimen location, notch orientation and examination ISO 9606-1, Approval testing of welders Fusion welding Part 1: Steels ISO 9606-2, Qualificat

27、ion test of welders Fusion welding Part 2: Aluminium and aluminium alloys ISO 9712, Non-destructive testing Qualification and certification of personnel ISO 10474, Steel and steel products Inspection documents ISO 14732, Welding personnel Approval testing of welding operators for fusion welding and

28、of resistance weld setters for fully mechanized and automatic welding of metallic materials ISO 15607, Specification and qualification of welding procedures for metallic materials General rules ISO 15613, Specification and qualification of welding procedures for metallic materials Qualification base

29、d on pre-production welding test ISO 15614-1, Specification and qualification of welding procedures for metallic materials Welding procedures test Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys BS ISO 21009-1:2008ISO 21009-1:2008(E) 2 ISO 2008 All rights reservedIS

30、O 15614-2, Specification and qualification of welding procedures for metallic materials Welding procedure test Part 2: Arc welding of aluminium and its alloys ISO 17636, Non-destructive testing of welds Radiographic testing of fusion-welded joints ISO 21010, Cryogenic vessels Gas/materials compatibi

31、lity ISO 21013-3, Cryogenic vessels Pressure-relief accessories for cryogenic service Part 3: Sizing and capacity determination ISO 21028-1 Cryogenic vessels Toughness requirements for materials at cryogenic temperature Part 1: Temperatures below -80 C ISO 21028-2 Cryogenic vessels Toughness require

32、ments for materials at cryogenic temperature Part 2: Temperatures between -80 C and -20 C ISO 23208, Cryogenic vessels Cleanliness for cryogenic service ISO 21009-2, Cryogenic vessels Static vacuum insulated vessels Part 2: Operational requirements ISO 21011, Cryogenic vessels Valves for cryogenic s

33、ervice EN 10028-7, Flat products made of steels for pressure purposes Part 7: Stainless steels EN 13068-3, Non-destructive testing Radioscopic testing Part 3: General principles of radioscopic testing of metallic materials by X- and gamma rays ASME Boiler and Pressure Vessel Code, Section V: Nondest

34、ructive Examination 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 accessories service equipment which has a safety related function with respect to pressure containment and/or control EXAMPLE Accessories include protective or limiting devic

35、es, controlling and monitoring devices, valves and indicators. 3.2 automatic welding welding in which the parameters are automatically controlled NOTE Some of these parameters may be adjusted to a limited extent, either manually or automatically, during welding to maintain the specified welding cond

36、itions. 3.3 bursting disc device non-reclosing pressure relief device ruptured by differential pressure NOTE The bursting disc device is the complete assembly of installed components including, where appropriate, the bursting disc holder. BS ISO 21009-1:2008ISO 21009-1:2008(E) ISO 2008 All rights re

37、served 33.4 cryogenic fluid refrigerated liquefied gas gas which is partially liquid because of its low temperature NOTE This includes totally evaporated liquids and supercritical fluids. EXAMPLE In ISO 21009, the (refrigerated, but) non-toxic gases, and mixtures of them, shown in Table 1, are refer

38、red to as cryogenic fluids. Table 1 Refrigerated but non toxic gases classification code Identification number, name and description 3 A Asphyxiant gases 1913 Neon, refrigerated liquid 1951 Argon, refrigerated liquid 1963 Helium, refrigerated liquid 1970 Krypton, refrigerated liquid 1977 Nitrogen, r

39、efrigerated liquid 2187 Carbon dioxide, refrigerated liquid 2591 Xenon, refrigerated liquid 3136 Trifluoromethane, refrigerated liquid 3158 Gas, refrigerated liquid, not otherwise specified (NOS) 3 O Oxidizing gases 1003 Air, refrigerated liquid 1073 Oxygen, refrigerated liquid 2201 Nitrous oxide, r

40、efrigerated liquid, oxidizing 3311 Gas, refrigerated liquid, oxidizing, NOS 3 F Flammable gases 1038 Ethylene, refrigerated liquid 1961 Ethane, refrigerated liquid 1966 Hydrogen, refrigerated liquid 1972 Methane, refrigerated liquid or natural gas, refrigerated liquid, with high methane content 3138

41、 Ethylene, acetylene and propylene mixture, refrigerated liquid, containing at least 71,5 % ethylene with not more than 22,5 % acetylene and not more than 6 % propylene 3312 Gas, refrigerated liquid, flammable, NOS The flammable gases and mixtures of them may be mixed with: helium, neon, nitrogen, a

42、rgon, carbon dioxide. Oxidizing and flammable gases may not be mixed. NOTE The classification code, identification number, name and description are according to UN codes. BS ISO 21009-1:2008ISO 21009-1:2008(E) 4 ISO 2008 All rights reserved3.5 documentation technical documents delivered by the manuf

43、acturer to the owner consisting of: all certificates establishing the conformity with this part of ISO 21009 (e.g. material, pressure test, cleanliness, safety devices); a short description of the vessel (including characteristic data, etc.); a list of fluids and their net mass for which the cryogen

44、ic vessel is designed; an operating manual (for the user) that contains a short description of the vessel (including characteristic data, etc.), a statement that the vessel is in conformity with this part of ISO 21009, and the instructions for normal operation. 3.6 gross volume of the inner vessel i

45、nternal volume of the inner vessel , excluding nozzles, pipes etc. determined at minimum design temperature and atmospheric pressure 3.7 handling loads loads exerted on the static cryogenic vessel in all normal transport operations including loading, unloading, pressure loading during transportation

46、, installation, etc. 3.8 inner vessel pressure vessel intended to contain the cryogenic fluid to be stored 3.9 manufacturer of the static cryogenic vessel company that carries out the final assembly, including the final acceptance test, of the static cryogenic vessel 3.10 maximum allowable pressure

47、maximum pressure permissible at the top of the vessel in its normal operating position 3.11 net volume of the inner vessel volume of the inner vessel, below the inlet to the relief devices, excluding nozzles, pipes etc., determined at minimum design temperature and atmospheric pressure 3.12 normal o

48、peration intended operation of the vessel either up to the maximum allowable pressure or subjected to handling loads 3.13 outer jacket gas-tight enclosure which contains the inner vessel and enables the vacuum to be established 3.14 piping system tubes, pipes and associated components which can come

49、 in contact with cryogenic fluids including valves, fittings, pressure relief devices, and their supports BS ISO 21009-1:2008ISO 21009-1:2008(E) ISO 2008 All rights reserved 53.15 pressure gauge pressure pressure relative to atmospheric pressure 3.16 relief plate plate retained by atmospheric pressure which allows relief of excess internal pressure, generally from the vacuum jacket 3.17 relief plug plug retained by atmospheric press