BS ISO 16858-2013 Ships and marine technology Loose gear of lifting appliances on ships Pulleys《船舶和海洋技术 船舶用起重设备可拆卸零部件 滑轮装置》.pdf

《BS ISO 16858-2013 Ships and marine technology Loose gear of lifting appliances on ships Pulleys《船舶和海洋技术 船舶用起重设备可拆卸零部件 滑轮装置》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 16858-2013 Ships and marine technology Loose gear of lifting appliances on ships Pulleys《船舶和海洋技术 船舶用起重设备可拆卸零部件 滑轮装置》.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS ISO 16858:2013Ships and marine technology Loose gear of liftingappliances on ships PulleysCopyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-

2、BS ISO 16858:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 16858:2013.The UK participation in its preparation was entrusted to TechnicalCommittee SME/32/-/4, Ships and marine technology - Outfitting anddeck machinery.A list of organizations represented o

3、n this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 75011 3IC

4、S 47.020.40; 47.020.50Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 28 February 2014.Amendments issued since publicationDate Text affectedCopyright British Stand

5、ards Institution Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS ISO 16858:2013 ISO 2013Ships and marine technology Loose gear of lifting appliances on ships PulleysNavires et technologie maritime Access

6、oires mobiles des appareils de levage sur les navires PouliesINTERNATIONAL STANDARDISO16858First edition2013-12-15Reference numberISO 16858:2013(E)Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking permitted

7、without license from IHS-,-,-BS ISO 16858:2013ISO 16858:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2013All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanica

8、l, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax

9、+ 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandCopyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS ISO 16858:2013ISO 16858:2013(E) ISO

10、2013 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Sheave components . 14 Designation of sheaves . 35 Technical requirements 35.1 Materials . 35.2 Ranges 35.3 Process . 35.4 Assembly requirements 45.5 Accuracy requirements 45.6 Special explanations . 76 Test req

11、uirements . 77 Inspection rules . 78 Package, transportation, and storage . 88.1 Package 88.2 Transportation 88.3 Storage . 89 Use, maintenance, and scrapping standards of sheaves 8Annex A (informative) Common hot-rolled sheave ranges . 9Bibliography .14Copyright British Standards Institution Provid

12、ed by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS ISO 16858:2013ISO 16858:2013(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO membe

13、r bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmenta

14、l and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance ar

15、e described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is

16、drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or

17、on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity asses

18、sment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 8, Ships and marine technology, Subcommittee SC 4, Outfitting and deck ma

19、chinery.iv ISO 2013 All rights reservedCopyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS ISO 16858:2013INTERNATIONAL STANDARD ISO 16858:2013(E)Ships and marine techn

20、ology Loose gear of lifting appliances on ships Pulleys1 ScopeThis International Standard specifies the structural types, basic parameters, technical requirements, test methods, inspection rules, marking, storage, and transportation of sheaves, loose gear of lifting appliances on ships.This Internat

21、ional Standard is applicable to hot-rolled sheaves of lifting appliances on ships.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undat

22、ed references, the latest edition of the referenced document (including any amendments) applies.ISO 16855, Ships and Marine Technology Loose gear of lifting appliances on ships General requirements3 Sheave componentsFor the components and basic dimensions of hot-rolled sheaves, see Figure 1. ISO 201

23、3 All rights reserved 1Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS ISO 16858:2013ISO 16858:2013(E)Key1 rim2 plate3 hub4 bolt5 spacer6 spacer sleeve7 bearing8 d

24、ust washer (optional)Figure 1 Sheave components2 ISO 2013 All rights reservedCopyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS ISO 16858:2013ISO 16858:2013(E)4 Desig

25、nation of sheavesFigure Example5 Technical requirements5.1 MaterialsThe materials of sheave components shall comply with the provisions in Table 1.Table 1 Requirements of component materialsComponent name MaterialsRim, plate, hub s 235 MPa for common carbon steelSpacer s 235 MPa for common carbon st

26、eel or b 160 MPa for gray cast-ironSpacer sleeve s 600 MPa for quality carbon steelBolt Above grade 8,8 specified in ISO 898Dust cover Wool felt5.2 RangesFor the ranges of sheaves, see Annex A.5.3 Process5.3.1 Rims and webThe rims and web of sheaves shall be manufactured from a single steel piece, w

27、ith groove produced by hot rolling process.5.3.2 Welding and weld5.3.2.1 Welding materials used for sheaves shall match the strength of welded materials, in accordance with International Standards.5.3.2.2 The rims and hubs of sheaves shall be welded with groove weld, with double groove preferred. Th

28、e types of weld shall be in accordance with the related provisions of ISO.5.3.2.3 The appearance shall have no quality defects such as steel pits, splashes, slag, undercuts, and surface cracks after welding. ISO 2013 All rights reserved 3Copyright British Standards Institution Provided by IHS under

29、license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS ISO 16858:2013ISO 16858:2013(E)5.3.2.4 After welding of rims and hubs, and before machining of sheaves, the sheave weld shall be adequately stabilized through thermal or vibrato

30、ry stress relief, to ensure dimensional stability.5.3.3 Surface treatment5.3.3.1 The surface roughness of rope grooves shall not be less than 12,5; their surface hardness shall be HB260 minimum.5.3.3.2 Machining positions of sheaves and open positions such as spacer sleeves shall be painted with ant

31、irust oil to prevent corrosion; non-machining positions shall be painted with antirust paint after the surface removal of rust.5.4 Assembly requirements5.4.1 Components can be assembled only after they pass tests.5.4.2 Rolling bearings shall be cleaned before assembly, with clean, rustless, and burr

32、-free contact surface.5.4.3 The fit between outer rings of rolling bearings and hubs of sheaves is N7; the fit between inner rings and shafts is n6.5.4.4 After assembly, sheaves can turn flexibly around the shaft without blocking, when manually moved.5.5 Accuracy requirements5.5.1 For the requiremen

33、ts on the limit deviation of outside diameter D1, see Table 2.Table 2 Requirements on limit deviation of outside diameter D1Dimension in millimetresOutside diameter D1Limit deviation t1250 0,5250500 1,05001 000 1,51 0001 200 2,01 2001 500 2,51 5001 800 3,01 8002 000 3,55.5.2 For the requirements on

34、the limit deviation of groove minor diameter D, see Table 3.4 ISO 2013 All rights reservedCopyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS ISO 16858:2013ISO 16858:2

35、013(E)Table 3 Requirements on limit deviation of groove minor diameter DDimension in millimetresGroove minor diameter DLimit deviation t2250 +2,5250500 +3,05001 000 +4,01 0001 200 +5,01 2001 500 +6,01 5001 800 +7,01 8002 000 +8,05.5.3 For the requirements on the limit deviation of groove radius R, s

36、ee Table 4.Table 4 Requirements on limit deviation of groove radius RDimension in millimetresBasic dimensions RLimit deviation t315 +1,01530 +1,55.5.4 For the limit deviation of rim width (W + 2 m), see Table 5.Table 5 Limit deviation of rim width (W + 2 m) Dimension in millimetresRim width (W + 2 m

37、)Limit deviation t450 +275 +3108 +4136 +55.5.5 The lateral run-out tolerance of grooves (see Figure 2) shall comply with the requirements given in Table 6.Table 6 Lateral run-out tolerance of groovesDimension in millimetresGroove minor diameter DLimit deviation t5250 2,0250500 2,55001 000 3,01 0001

38、200 4,01 2001 500 5,01 5001 800 6,0 ISO 2013 All rights reserved 5Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS ISO 16858:2013ISO 16858:2013(E)Figure 2 Lateral r

39、un-out tolerance of grooves5.5.6 Cycle run-out t6at the minor diameter D of sheaves shall comply with Formula (1) (see also Figure 3):tD6251000,(1)5.5.7 Cylindricity tolerance t7at the hub bore D0shall comply with Formula (2) (see also Figure 3):t7 tolerancezoneof D02(2)5.5.8 Profile tolerance t8of

40、a line within the tolerance zone of groove radius shall comply with Formula (3) (see also Figure 3):t8 limit deviation t3of groove radius R (3)6 ISO 2013 All rights reservedCopyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproductio

41、n or networking permitted without license from IHS-,-,-BS ISO 16858:2013ISO 16858:2013(E)Figure 3 Cylindricity tolerance t7at hub bore D05.6 Special explanationsFor other hot-rolled sheaves (different from that in 5.1, 5.2, 5.3, and 5.4 in terms of components, materials, process, assembly requiremen

42、ts, and accuracy requirements), strength shall be calculated during the design and the result shall meet the test requirements of Clause 6, and such sheaves can also be used in lifting appliances on ships, with the special consent of related organizations (such as classification societies) or as agr

43、eed on by the supplier and the purchaser.6 Test requirementsTest requirements should be in accordance with the test requirements for blocks in ISO 16855.7 Inspection rulesSheaves shall be inspected and tested by the quality control department of the manufacturer according to the technical requiremen

44、ts and test methods of this International Standard. Inspection shall be made with the items listed in Table 8. ISO 2013 All rights reserved 7Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking permitted withou

45、t license from IHS-,-,-BS ISO 16858:2013ISO 16858:2013(E)Table 8 Inspection items of sheavesNo. Inspection items1 Limit deviation t1of outside diameter D12 Deviation t2of groove minor diameter D3 Limit deviation t3of groove radius R4 Limit deviation t4of rim width (W + 2 m)5 Lateral run-out toleranc

46、e t5of grooves6 Cycle run-out t6at minor diameter D of sheaves7 Cylindricity tolerance t7of hub bores D08 Profile tolerance t8of a line within the tolerance zone of groove radius9 Surface hardness of grooves10 Appearance quality of welds11 Internal quality of welds8 Package, transportation, and stor

47、age8.1 PackageThe package of sheaves shall protect them from damage or corrosion in accordance with International Standards.8.2 TransportationCollision that makes sheaves distorted or damaged is strictly prohibited during transportation.8.3 StorageSheaves shall be stored at dry and well-ventilated p

48、laces, away from acid, alkaline, or other corrosive substances, and protected against erosion of rain, snow, and water, as well as long-time exposure to sunlight.9 Use, maintenance, and scrapping standards of sheaves9.1 Upon installation on the appliances, the rotation and wear of sheaves shall be checked before each use, with major check items as follows:a) wear of rope grooves;b) prese