BS ISO 12044-2014 Rolling bearings Single-row angular contact ball bearings Chamfer dimensions for outer ring non-thrust side《滚动轴承 单列角面接触的滚珠轴承 外圈无止推侧面倒角尺寸》.pdf

《BS ISO 12044-2014 Rolling bearings Single-row angular contact ball bearings Chamfer dimensions for outer ring non-thrust side《滚动轴承 单列角面接触的滚珠轴承 外圈无止推侧面倒角尺寸》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 12044-2014 Rolling bearings Single-row angular contact ball bearings Chamfer dimensions for outer ring non-thrust side《滚动轴承 单列角面接触的滚珠轴承 外圈无止推侧面倒角尺寸》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS ISO 12044:2014Rolling bearings Single-rowangular contact ball bearings Chamfer dimensions forouter ring non-thrust sideBS ISO 12044:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 12044:2014. It supersedes BS ISO 12044:1995 whic

2、h is withdrawn.The UK participation in its preparation was entrusted to Technical Committee MCE/7, Rolling bearings.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contrac

3、t. Users are responsible for its correct application. The British Standards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 77274 0ICS 21.100.20Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the author

4、ity of the Standards Policy and Strategy Committee on 31 May 2014.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 12044:2014 ISO 2014Rolling bearings Single-row angular contact ball bearings Chamfer dimensions for outer ring non-thrust sideRoulements Roulements bille

5、s contact oblique une range Dimensions des arrondis des bagues ct non chargINTERNATIONAL STANDARDISO12044Second edition2014-05-01Reference numberISO 12044:2014(E)BS ISO 12044:2014ISO 12044:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwis

6、e specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address belo

7、w or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 12044:2014ISO 12044:2014(E) ISO 2014 All rights reserved iiiContents PageForeword

8、 iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Symbols 15 Chamfer dimensions . 2Bibliography 4BS ISO 12044:2014ISO 12044:2014(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of

9、 preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental

10、, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO

11、/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibili

12、ty that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of pat

13、ent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as info

14、rmation about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 4, Rolling bearings, Subcommittee SC 12, Ball bearings.This second edition cancels and replaces

15、 the first edition (ISO 12044:1995), which has been technically revised.iv ISO 2014 All rights reservedBS ISO 12044:2014INTERNATIONAL STANDARD ISO 12044:2014(E)Rolling bearings Single-row angular contact ball bearings Chamfer dimensions for outer ring non-thrust side1 ScopeThis International Standar

16、d specifies chamfer dimensions for outer ring, non-thrust side of single-row angular contact ball bearings, where the dimensions differ from those specified in ISO 15.1It is applicable to bearings in the diameter series 9, 0, and 2 for contact angles, up to and including 30, and in the diameter seri

17、es 2 and 3 for contact angles over 30.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the ref

18、erenced document (including any amendments) applies.ISO 5593, Rolling bearings VocabularyISO 15241, Rolling bearings Symbols for physical quantities3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 5593 apply.4 SymbolsFor the purposes of this document,

19、the symbols given in ISO 15241 and the following apply.The symbols shown in Figure 1 and the values given in Table 1 denote nominal dimensions, unless specified otherwise.d bearing bore diameterr1chamfer dimension of outer ring non-thrust sider1s minsmallest single chamfer dimension of outer ring no

20、n-thrust side contact angle ISO 2014 All rights reserved 1BS ISO 12044:2014ISO 12044:2014(E)r1r1dNOTE 1 For tandem mounting, check that there is sufficient contact area between the mating ring faces.NOTE 2 The figure shows an example of design.Figure 1 Chamfer dimension for outer ring non-thrust sid

21、e of single-row angular contact ball bearing5 Chamfer dimensionsThe chamfer dimensions for outer ring non-thrust side of single-row angular contact ball bearings are given in Table 1.Chamfer dimension, r1, applies at the corner indicated in Figure 1 and specified with r1s minin Table 1. See ISO 5822

22、for the corresponding largest single chamfer dimensions to the r1s minin Table 1.Table 1 Chamfer dimensionsDimensions in millimetresdr1s minDiameter series Diameter series9 0 2 2 3 30 308 0,1 0,1 0,15 0,15 0,159 0,1 0,1 0,15 0,15 0,310 0,1 0,1 0,3 0,3 0,312 0,1 0,1 0,3 0,3 0,615 0,1 0,1 0,3 0,3 0,62

23、 ISO 2014 All rights reservedBS ISO 12044:2014ISO 12044:2014(E)dr1s minDiameter series Diameter series9 0 2 2 3 30 3017 0,1 0,1 0,3 0,6 0,620 0,15 0,3 0,3 0,6 0,625 0,15 0,3 0,3 0,6 0,630 0,15 0,3 0,3 0,6 0,635 0,15 0,3 0,3 0,6 140 0,15 0,3 0,6 0,6 145 0,15 0,3 0,6 0,6 150 0,15 0,3 0,6 0,6 155 0,3 0

24、,6 0,6 1 160 0,3 0,6 0,6 1 1,165 0,3 0,6 0,6 1 1,170 0,3 0,6 0,6 1 1,175 0,3 0,6 0,6 1 1,180 0,3 0,6 1 1 1,185 0,6 0,6 1 1 1,190 0,6 0,6 1 1 1,195 0,6 0,6 1,1 1,1 1,1100 0,6 0,6 1,1 1,1 1,1105 0,6 1 1,1 1,1 1,1110 0,6 1 1,1 1,1 1,1120 0,6 1 1,1 1,1 1,1130 0,6 1 1,1 1,1 1,5140 0,6 1 1,1 1,1 1,5150 1

25、1 1,1 1,1 1,5160 1 1 1,1 1,1 1,5170 1 1,1 1,5 1,5 1,5180 1 1,1 1,5 1,5 2190 1 1,1 1,5 1,5 2200 1 1,1 1,5 1,5 2220 1 1,1 1,5 1,5 2240 1 1,1 1,5 1,5 2Table 1 (continued) ISO 2014 All rights reserved 3BS ISO 12044:2014ISO 12044:2014(E)Bibliography1 ISO 15, Rolling bearings Radial bearings Boundary dime

26、nsions, general plan2 ISO 582, Rolling bearings Chamfer dimensions Maximum values4 ISO 2014 All rights reservedBS ISO 12044:2014BS ISO 12044:2014ISO 12044:2014(E) ISO 2014 All rights reservedICS 21.100.20Price based on 4 pagesThis page deliberately left blankBSI is the national body responsible for

27、preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High

28、Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined thr

29、ough our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website

30、 at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international

31、and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British St

32、andards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on t

33、he purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more

34、 about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can

35、be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a

36、 British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used

37、 (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by

38、any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW