BS ISO 1203-1998 Photography - Roll film cameras - Back window location《摄影技术 胶卷摄影机 后窗位置》.pdf

《BS ISO 1203-1998 Photography - Roll film cameras - Back window location《摄影技术 胶卷摄影机 后窗位置》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 1203-1998 Photography - Roll film cameras - Back window location《摄影技术 胶卷摄影机 后窗位置》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 1203:1998 Photography Roll film cameras Back window location ICS 37.040.10BSISO1203:1998 This British Standard, having been prepared under the directionof the Consumer Products and Services Sector Committee, was published underthe authority ofthe Standards Committee andcomesi

2、nto effect on 15 December 1998 BSI 05-1999 ISBN 0 580 30773 5 National foreword This British Standard reproduces verbatim ISO1203:1998 and implements it as the UK national standard. The UK participation in its preparation was entrusted to Technical Committee CPW/42, Photography, which has the respon

3、sibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A li

4、st of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “Internatio

5、nal Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a Briti

6、sh Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the ISO title page, pages ii to iv, page 1 and a back cover. This standard has been updated (see copyright date) and may have had amen

7、dments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSISO1203:1998 BSI 05-1999 i Contents Page National foreword Inside front cover Foreword iii Text of ISO 1203 1ii blankBSISO1203:1998 ii BSI 05-1999

8、 Contents Page Foreword iii 1 Scope 1 2 Back window location 1 Figure 1 Location of back window 1 Table 1 Locating dimensions for back window 1BSISO1203:1998 BSI 05-1999 iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO

9、member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, govern

10、mental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the

11、member bodies for voting. Publication as an International Standard requires approval by at least75% of the member bodies casting a vote. International Standard ISO1203 was prepared by Technical Committee ISO/TC42, Photography. This fourth edition cancels and replaces the third edition (ISO1203:1984)

12、, of which it constitutes a technical revision. The picture sizes in the third edition have been transferred to ISO1754:1998. Descriptors: Photography, photographic equipment, cameras, roll films, windings, inspection devices, position (location), dimensions.iv blankBSISO1203:1998 BSI 05-1999 1 1 Sc

13、ope This International Standard specifies the location of back windows of roll film cameras in relation to the number of exposures and film sizes they are designed to accommodate. 2 Back window location The locating dimensions shown in Figure 1 are given in Table 1. Table 1 Locating dimensions for b

14、ack window Figure 1 Location of back window Dimensions in millimetres Trade designation of nominal negative size Exposure per roll film size X Y 4,5 6 16 120 0 + 18,0 6 6 12 120 0 0 6 9 8 120 + 35,5 19,5 The tolerance for dimensions X and Y are1,6mm. The diameter of the back window is9,0mm minimum.B

15、S ISO 1203:1998 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions Briti

16、shStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while

17、 using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically re

18、ceive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementati

19、on of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic informatio

20、n services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For de

21、tails of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyrig

22、ht, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the st

23、andard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.