BS ISO 11093-6-2007 Paper and board - Testing of cores - Determination of bending strength by the three-point method《纸和纸板 纸芯的试验 用三点法测定抗弯强度》.pdf

《BS ISO 11093-6-2007 Paper and board - Testing of cores - Determination of bending strength by the three-point method《纸和纸板 纸芯的试验 用三点法测定抗弯强度》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 11093-6-2007 Paper and board - Testing of cores - Determination of bending strength by the three-point method《纸和纸板 纸芯的试验 用三点法测定抗弯强度》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58strength by the three-point methodICS 85.060Paper and board Testing of cores Part 6: Determination

2、of bending BRITISH STANDARDBS ISO 11093-6:2005BS ISO 11093-6:2005This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 March 2007 BSI 2007ISBN 978 0 580 50432 7Amendments issued since publicationAmd. No. Date Commentscontract. Users are responsi

3、ble for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations. National forewordThis British Standard was published by BSI. It is the UK implementation of ISO 11093-6:2005. It supersedes BS ISO 11093-6:1996 which is withdrawn.The UK participation in

4、 its preparation was entrusted to Technical Committee PAI/11, Methods of test for paper, board and pulps.A list of organizations represented on PAI/11 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a Reference numberISO 11093-

5、6:2005(E)INTERNATIONAL STANDARD ISO11093-6Second edition2005-05-01Paper and board Testing of cores Part 6: Determination of bending strength by the three-point method Papier et carton Essais des mandrins Partie 6: Dtermination de la rsistance la flexion par la mthode des trois points BS ISO 11093-6:

6、2005ii iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for

7、 which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on a

8、ll matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are

9、 circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held re

10、sponsible for identifying any or all such patent rights. ISO 11093-6 was prepared by Technical Committee ISO/TC 6, Paper, board and pulps. This second edition cancels and replaces the first edition (ISO 11093-6:1996), which has been technically revised. ISO 11093 consists of the following parts, und

11、er the general title Paper and board Testing of cores: Part 1: Sampling Part 2: Conditioning of test samples Part 3: Determination of moisture content using the oven drying method Part 4: Measurement of dimensions Part 5: Determination of characteristics of concentric rotation Part 6: Determination

12、of bending strength by the three-point method Part 7: Determination of flexural modulus by the three-point method Part 8: Determination of natural frequency and flexural modulus by experimental modal analysis Part 9: Determination of flat crush resistance BS ISO 11093-6:2005blank1Paper and board Tes

13、ting of cores Part 6: Determination of bending strength by the three-point method 1 Scope This part of ISO 11093 specifies a three-point method for the determination of the bending strength of cylindrical board cores which meet the following criteria: internal diameter: 50 mm to 300 mm; minimum wall

14、 thickness: 5 mm; minimum test length of core (span): 1 100 mm. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced documen

15、t (including any amendments) applies. ISO 7500-1, Metallic materials Verification of static uniaxial testing machines Part 1: Tension/compression testing machines Verification and calibration of the force-measuring system ISO 11093-1, Paper and board Testing of cores Part 1: Sampling ISO 11093-2, Pa

16、per and board Testing of cores Part 2: Conditioning of test samples 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 bending strength maximum resistance of a test piece of given dimensions against bending until breakage under specified conditi

17、ons 4 Principle The core test piece is considered as a “beam“ in the mechanics of material approach. During the test, the test piece is stressed by a vertical force (F) at the midpoint of its length while being supported at each end only (see Figure 1). For the determination of the bending strength,

18、 stress is applied until the test piece breaks. BS ISO 11093-6:20052 F applied force L test length of the core (span) Figure 1 Three-point method of beam loading 5 Apparatus The following apparatus shall be used. 5.1 Load-testing machine The load-testing machine shall be capable of applying a load a

19、t a constant relative speed of (25 2,5) mm/min and shall be calibrated and verified to conform to the requirements of ISO 7500-1. The switch-off limit for the breaking force F for a testing machine with an automatic break detection is defined by 30 N, or 3 % from the true value. The direction of the

20、 load application is perpendicular to the test piece axis and shall be adjusted with an accuracy of 1. 5.2 Two prism supports The two prism supports (see Figure 2), shall each have an angle between the two faces supporting the core test piece of 120 2. The length (l), parallel to the core length, sh

21、all be (50 1) mm. The width (b) shall be large enough to allow the core test piece to rest on the supporting faces and not on the outer edges of the prism. The support edges shall be rounded to a radius (r) of (0,5 0,1) mm. The prism support shall be positioned on pivots on each side of the prism, s

22、o as to ensure uniform contact of the test piece on the prism and a constant measuring length during the test. BS ISO 11093-6:20053Figure 2 Schematic drawing of prism support 5.3 Load prism The load prism is used to apply the load to the core surface and is of the same basic shape and dimensions as

23、the prism supports (5.2), except that its length l (see Figure 2) parallel to the core length L (see Figure 1), shall be (100 1) mm. 6 Sampling and preparation Ensure that the test pieces used are representative of the sample received. If the determination is to represent a lot, the sampling procedu

24、re shall be carried out in accordance with ISO 11093-1. Prepare at least three test pieces such that their lengths are 100 mm greater than the test length of the core, L (see Figure 1). Condition the test pieces in accordance with ISO 11093-2. 7 Procedure Carry out the test under the same atmospheri

25、c conditions as those used to condition the test pieces. Arrange the test assembly such that the test piece is located centrally on the prism supports to within 5 mm, and the load prism is positioned centrally between the support prisms to within 2 mm and diametrically opposed to them. The distance

26、between the two axes of the support prisms is the test length of the core, L (see Figure 1). The test length of the core shall be in accordance with Clause 6 and shall be known to an accuracy of 2 mm. BS ISO 11093-6:20054 Apply the load at a constant rate of (25 2,5) mm/min until the test piece brea

27、ks. Record the maximum load value, in kilonewtons, as the bending strength. Repeat the test procedure for the remaining test pieces. Calculate the mean bending strength. 8 Test report The test report shall include the following information a) a reference to this part of ISO 11093; b) complete identi

28、fication of the samples tested and the sampling method used; c) date and place of sampling; d) date and place of testing, name and signature of tester; e) number of test pieces; f) core dimensions, i.e. length, internal diameter, external diameter; g) test length of core (L); h) individual and avera

29、ge values, expressed in kilonewtons, for bending strength; i) any departure from the procedure specified in this part of ISO 11093 and any circumstances that may have affected the results. BS ISO 11093-6:2005blankBS ISO BSI389 Chiswick High RoadLondonW4 4AL11093-6:2005BSI British Standards Instituti

30、onBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should ma

31、ke sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee res

32、ponsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for al

33、l BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI po

34、licy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service.

35、 Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and rece

36、ive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can

37、 be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright,

38、Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standar

39、d, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.