BS ISO 11093-4-2016 Paper and board Testing of cores Measurement of dimensions《纸和纸板 芯层试验 第1部分 尺寸测量》.pdf
《BS ISO 11093-4-2016 Paper and board Testing of cores Measurement of dimensions《纸和纸板 芯层试验 第1部分 尺寸测量》.pdf》由会员分享,可在线阅读,更多相关《BS ISO 11093-4-2016 Paper and board Testing of cores Measurement of dimensions《纸和纸板 芯层试验 第1部分 尺寸测量》.pdf(22页珍藏版)》请在麦多课文档分享上搜索。
1、BS ISO 11093-4:2016Paper and board Testing ofcoresPart 4: Measurement of dimensionsBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 11093-4:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 11093-4:2016.It supersedes BS
2、 ISO 11093-4:1997 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PAI/11, Methods of test for paper, board and pulps.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to in
3、clude all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 85931 1ICS 85.060Compliance with a British Standard cannot confer immunity fromlegal obligations.This Britis
4、h Standard was published under the authority of theStandards Policy and Strategy Committee on 30 June 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 11093-4:2016 ISO 2016Paper and board Testing of cores Part 4: Measurement of dimensionsPapier et carton Essais d
5、es mandrins Partie 4: Mesurage des dimensionsINTERNATIONAL STANDARDISO11093-4Second edition2016-06-01Reference numberISO 11093-4:2016(E)BS ISO 11093-4:2016ISO 11093-4:2016(E)ii ISO 2016 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in SwitzerlandAll rights reserved. Unless othe
6、rwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
7、below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 11093-4:2016ISO 11093-4:2016(E)Foreword iv1 Scope . 12 Normative references 13 Terms
8、and definitions . 14 Sampling 25 Conditioning 26 Measurement of internal diameters 26.1 General . 26.2 Method A 36.2.1 Apparatus . 36.2.2 Procedure . 36.3 Method B 36.3.1 Apparatus . 36.3.2 Procedure . 36.4 Method C 36.4.1 Apparatus . 36.4.2 Procedure . 36.5 Calculation 47 Measurement of external di
9、ameters . 47.1 General . 47.2 Method D 47.2.1 Apparatus . 47.2.2 Procedure . 47.3 Method E 57.3.1 Apparatus . 57.3.2 Procedure . 57.4 Method F . 57.4.1 Apparatus . 57.4.2 Procedure . 58 Measurement of wall thickness 68.1 General . 68.2 Method G 68.2.1 Apparatus . 68.2.2 Procedure . 68.3 Method H 68.
10、3.1 Apparatus . 68.3.2 Procedure . 68.4 Calculation 79 Measurement of length 79.1 Apparatus 79.2 Procedure 710 Test report . 7Annex A (informative) Example of an internal-tri-point micrometer . 8Annex B (informative) Examples of vernier callipers . 9Annex C (informative) Other examples .11 ISO 2016
11、All rights reserved iiiContents PageBS ISO 11093-4:2016ISO 11093-4:2016(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO tec
12、hnical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closel
13、y with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria nee
14、ded for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
15、rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in
16、this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers
17、 to Trade (TBT) see the following URL: Foreword - Supplementary information.The committee responsible for this document is ISO/TC 6, Paper, board and pulps.This second edition cancels and replaces the first edition (ISO 11093-4:1997), which has been technically revised.ISO 11093 consists of the foll
18、owing parts, under the general title Paper and board Testing of cores: Part 1: Sampling Part 2: Conditioning of test samples Part 3: Determination of moisture content using the oven drying method Part 4: Measurement of dimensions Part 5: Determination of characteristics of concentric rotation Part 6
19、: Determination of bending strength by the three-point method Part 7: Determination of flexural modulus by the three-point method Part 8: Determination of natural frequency and flexural modulus by experimental modal analysis Part 9: Determination of flat crush resistanceiv ISO 2016 All rights reserv
20、edBS ISO 11093-4:2016INTERNATIONAL STANDARD ISO 11093-4:2016(E)Paper and board Testing of cores Part 4: Measurement of dimensions1 ScopeThis part of ISO 11093 specifies test methods for the determination of the internal diameter, the external diameter, the wall thickness and the length, of paper and
21、 board cores.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (includi
22、ng any amendments) applies.ISO 13385-1, Geometrical product specifications (GPS) Dimensional measuring equipment Part 1: Callipers; Design and metrological characteristicsISO 3611, Geometrical product specifications (GPS) Dimensional measuring equipment: Micrometers for external measurements Design
23、and metrological characteristicsISO 11093-1, Paper and board Testing of cores Part 1: SamplingISO 11093-2, Paper and board Testing of cores Part 2: Conditioning of test samples3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.3.1internal diameterddim
24、ension of the internal width of the cylindrical coreNote 1 to entry: See Figure 1.3.2external diameterDdimension of the external width of the cylindrical coreNote 1 to entry: See Figure 1.3.3wall thicknesssdistance between the inner and outer surfaces of the coreNote 1 to entry: See Figure 1. ISO 20
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSISO1109342016PAPERANDBOARDTESTINGOFCORESMEASUREMENTOFDIMENSIONS 纸板 试验 部分 尺寸 测量 PDF

链接地址:http://www.mydoc123.com/p-583473.html