BS ISO 10263-5-2009 Earth-moving machinery - Operator enclosure environment - Windscreen defrosting system test method《土方机械 操作室环境 挡风玻璃除霜系统试验方法》.pdf

《BS ISO 10263-5-2009 Earth-moving machinery - Operator enclosure environment - Windscreen defrosting system test method《土方机械 操作室环境 挡风玻璃除霜系统试验方法》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 10263-5-2009 Earth-moving machinery - Operator enclosure environment - Windscreen defrosting system test method《土方机械 操作室环境 挡风玻璃除霜系统试验方法》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO10263-5:2009ICS 53.100NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDEarth-movingmachinery Operatorenclosure environmentPart 5: Windscreen defrosting systemtest methodThis British Standardwas published under theauthority of the StandardsPolicy and Strateg

2、yCommittee on 30 April2009 BSI 2009ISBN 978 0 580 57409 2Amendments/corrigenda issued since publicationDate CommentsBS ISO 10263-5:2009National forewordThis British Standard is the UK implementation of ISO 10263-5:2009. Itsupersedes BS 6912 22.5:1996 which is withdrawn.The UK participation in its pr

3、eparation was entrusted to TechnicalCommittee B/513/1, Earth moving machinery (International).A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible

4、 for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.-BS ISO 10263-5:2009Reference numberISO 10263-5:2009(E)ISO 2009INTERNATIONAL STANDARD ISO10263-5Second edition2009-02-01Earth-moving machinery Operator enclosure environment Part 5: Windscree

5、n defrosting system test method Engins de terrassement Environnement de lenceinte de loprateur Partie 5: Mthode dessai du systme de dgivrage du pare-brise BS ISO 10263-5:2009ISO 10263-5:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, t

6、his file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secre

7、tariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ens

8、ure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this publicati

9、on may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20

10、 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reservedBS ISO 10263-5:2009ISO 10263-5:2009(E) ISO 2009 All rights reserved iiiContents Page Foreword iv 1 Scope . 1 2 Normative references . 1 3 Terms and definition

11、s. 1 4 Test equipment . 2 5 Test conditions . 2 6 Test procedure 3 7 Minimum performance requirements . 4 8 Test report . 4 Annex A (informative) Example of report form for windscreen defrosting test. 9 Bibliography . 10 BS ISO 10263-5:2009ISO 10263-5:2009(E) iv ISO 2009 All rights reservedForeword

12、ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical

13、committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of elect

14、rotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the

15、member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for ident

16、ifying any or all such patent rights. ISO 10263-5 was prepared by Technical Committee ISO/TC 127, Earth-moving machinery, Subcommittee SC 2, Safety, ergonomics and general requirements. This second edition cancels and replaces the first edition (ISO 10263-5:1994), which has been technically revised.

17、 ISO 10263 consists of the following parts, under the general title Earth-moving machinery Operator enclosure environment: Part 1: Terms and definitions Part 2: Air filter element test method Part 3: Pressurization test method Part 4: Heating, ventilating and air conditioning (HVAC) test method and

18、performance Part 5: Windscreen defrosting system test method Part 6: Determination of effect of solar heating BS ISO 10263-5:2009INTERNATIONAL STANDARD ISO 10263-5:2009(E) ISO 2009 All rights reserved 1Earth-moving machinery Operator enclosure environment Part 5: Windscreen defrosting system test me

19、thod 1 Scope This part of ISO 10263 specifies a test method to determine the performance of windscreen defrosting systems of earth-moving machinery, fitted with an operator enclosure and a device for defrosting the windscreen. It includes tests that can be conducted with test equipment in commercial

20、ly available laboratory facilities, as well as in an appropriate outdoor environment. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of

21、the referenced document (including any amendments) applies. ISO 5353:1995, Earth-moving machinery, and tractors and machinery for agriculture and forestry Seat index point ISO 9249, Earth-moving machinery Engine test code Net power ISO 10263-1, Earth-moving machinery Operator enclosure environment P

22、art 1: Terms and definitions 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 10263-1 and the following apply. 3.1 windscreen defrosting system means intended to defrost the windscreen 3.2 daylight opening DLO maximum unobstructed opening through any

23、glazed aperture, with trim mouldings and mounting seals adjoining the glazed surface 3.3 defrosted area area of the windscreen consisting of dry cleared surface and melted or partially melted (wet) test coating, and excluding that area of the windscreen covered with dry test coating of ice NOTE For

24、further explanation of defrosted areas, see Figure 1. BS ISO 10263-5:2009ISO 10263-5:2009(E) 2 ISO 2009 All rights reserved3.4 heat transfer medium HTM means through which defroster system heating is achieved 3.5 defrosting removal and maintenance of an ice/frost-free window area for visibility 3.6

25、seat index point SIP point in the central, vertical and longitudinal plane of the SIP measuring device NOTE Adapted from ISO 5353:1995, definition 3.1. 4 Test equipment 4.1 Environmental chamber sufficiently large to contain the base machine or machine operator enclosure with provision for circulati

26、ng air. NOTE In lieu of an environmental chamber, the test may be conducted outside under test conditions similar to those in an environmental chamber (see 5.2). 4.2 Means of recording boundaries of windscreen areas defrosted. 4.3 Device to measure rotational frequency (rpm) with a measuring accurac

27、y of 2 % of observed value. 4.4 Stopwatch or other timing device. 4.5 Thermometers or other temperature measuring devices, with a measuring accuracy of 0,5 C. 4.6 Throttle control device (remote or auxiliary, if desired). 4.7 Spray device, to apply mist to the windscreen, with the following characte

28、ristics: a) fluid: distilled water; b) liquid nozzle size diameter: 1,7 mm; c) recommended operating gauge pressure: (345 20) kPa; d) spray pattern at 200 mm from spray nozzle: (300 50) mm wide. 4.8 Device to measure quantity of water provided by the spray device 2,5 %. 4.9 Auxiliary power supply fo

29、r heater blower motor when bench-testing operator enclosure only. 4.10 Anemometer to measure wind speed, within a measuring accuracy of 0,5 m/s. 5 Test conditions 5.1 The maximum ambient temperature for the heating system test shall be 15 C at a maximum ambient wind speed of 5 m/s. 5.2 If it is not

30、practical to test the base machine due to physical size limitations, the operators enclosure may be bench-tested, simulating the heat loads and system parameters imposed by the base machine on the enclosure. If this laboratory procedure is used, supplementary field testing should be carried out to c

31、onfirm the test results. BS ISO 10263-5:2009ISO 10263-5:2009(E) ISO 2009 All rights reserved 35.3 The machine shall be operated in accordance with the manufacturers recommended warm-up procedure, and then at rated speed under a maximum load of no more than 20 % of the maximum rated net engine power,

32、 determined in accordance with ISO 9249. 5.4 The HTM flow shall come from engine operation or from an independent HTM flow. The HTM flow shall result from engine operation as specified in 5.3. The independent HTM flow and temperature shall be the same as that resulting from operation of the machine

33、engine, in accordance with the requirement of 5.3. Following are three typical examples of HTM: liquid engine coolant; hydraulic oil; air/liquid obtained from an auxiliary heat source, i.e., gas-fired heater or oil-fired heater. 5.5 The HTM temperature shall be measured as close as possible to the i

34、nlet pipe of the heating unit. For those systems using more than one heater, it shall be measured at the inlet pipe of the heating unit receiving the first coolant flow. The HTM flow may be measured at any suitable point. The ambient outside air temperature and wind speed shall be measured at a loca

35、tion where it is not affected by the machine, and at a height equivalent to the air intake height on the operator enclosure, but no further than 10 m away. At the beginning of the test, the HTM shall be at ambient temperature. 5.6 Windscreen wiper blades and arms shall not come into contact with the

36、 windscreen glazed surface during ice application. Windscreen wipers may be used during the test. If windscreen wipers are used, the number of swipes and times are to be listed in the report. 5.7 Defroster and/or heating system blower(s) shall be on and at maximum speed. 5.8 The voltage at the termi

37、nals of the blower motor shall be no more than 15 % above the nominal rating of the system (for example 13,8 V for a 12 V system or 27,6 V for a 24 V system). 5.9 The temperature controls shall be at maximum heat position. 5.10 All engine, heating and defroster units shall be standard production par

38、ts or equivalent, adjusted within specified limits. 5.11 The engine bonnet (hood), doors and windows shall be closed. 5.12 If an auxiliary heater(s) is part of the standard heating and defroster system, it may be operated. 5.13 Auxiliary means of preheating the engine, etc. are permissible, providin

39、g they do not heat the HTM. Similarly, no simulated or actual solar heat load shall be allowed to strike the windscreen. 5.14 An operator may be in the enclosure throughout the duration of the test. 6 Test procedure 6.1 Thermally soak the machine until instrumentation can confirm that the HTM, winds

40、hield, HVAC system, duct work and enclosure temperatures are 15 C or below. BS ISO 10263-5:2009ISO 10263-5:2009(E) 4 ISO 2009 All rights reserved6.2 Following the machine soak period, form a coating of ice on the windscreen(s) by spraying (0,050 0,005) ml of water per square centimetre of glazed sur

41、face with a spray device. Apply coating in even, horizontal overlapping layers (to the outside surface) until the specified quantity of liquid has been applied. Upon completion of the icing process, allow an additional soak period of 30 min to 40 min. NOTE Measuring and applying spray to multiple pi

42、ece windshields as distinct separate steps will better ensure the correct ice thickness for each section. 6.3 Start the engine or heat source. Put the defrosting system into action, maintaining the test conditions specified in Clause 5 throughout the test period. Every 5 min for 1 h, outline the def

43、rosted areas on the inside surface of the windscreen. See also 8 d). 7 Minimum performance requirements The windscreen areas that shall be defrosted are defined in Table 1 for various families of earth-moving machines. Each area is defined by angles from the operators eye point 660 mm above and 20 m

44、m in front of the SIP as defined in ISO 5353. In the side view, the upper and lower boundaries of the areas are established by the intersection of two planes and the windshield glazing surface; the two planes being seen as lines converging at the eye point. The planes are fixed by angles above and b

45、elow the XX line. In the plane (top) view, the left and right boundaries of the areas are established by the intersection of two vertical planes and the windshield glazing surface; the two planes being seen as lines converging at the eye point. The planes are fixed by angles to the left and right of

46、 the XX line. See Figure 2. If any of the four planes, or portions of them established by the angles in Table 1, do not intersect the windscreen glazed surface but fall outside of the DLO, then relocate that part of the plane until it just intersects the windscreen glazed surface along a line which

47、lies entirely on the DLO and touches the moulding or frame. The areas used in determining the percentage of defrosted area are those areas on the outside glazed surface which are not within 25 mm of the edge of the DLO (pillars, division bar, header, etc.). The percentage is the ratio of defrosted a

48、rea to the defined area. Figure 2 illustrates all of these areas on a typical windscreen. After 60 min of testing, the percentage of defrosted area shall meet the minimum requirements specified in Table 2. The non-defrosted portions shall be located only along the windscreen frame or moulding. 8 Tes

49、t report The test report shall contain the following information: a) model and product identification number of the machine tested; b) ambient conditions outside the operator enclosure i.e. dry bulb temperature, moisture content (kg H2O/kg dry air), and wind speed; c) time necessary at the specified ambient temperature to defrost the minimum requirement area given in Table 2 for each area; d) the pattern of the defrosted area transferred to a transparent material by tracing, marked to